Home > Lyman > Firearms accessories > Lyman The Mag 2 Press Instructions Manual

Lyman The Mag 2 Press Instructions Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Lyman The Mag 2 Press Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 16 Lyman manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							THE T-MAG II PRESS
    The Lyman T-Mag Press features a powerful
    compound leverage with a unique position index-
    able turret and quick disconnect release system.
    This allows you to mount several die sets, pre-
    cisely locked in and ready to reload at all times.
    You may also mount your powder measure in
    one of the die stations if it is compatible with the
    7⁄8 x 14 threads (as many are).
    The Lyman #55 Powder Measure can be
    mounted to the turret using the Lyman 
    7⁄8 x 14
    Adapter. 
    A long steel handle adapted with a Ball type
    knob adapts easily for left or right hand opera-
    tions.
    Mounting the Press
    Remove the T-Mag Press from the packing box
    and position it against the edge of your bench top in the most convenient location, usually
    near the center of the bench, leaving a work area on each side of the press. Mark the position
    of the mounting holes and drill them; then, using 
    3⁄8 bolts and suitable washers and nuts,
    securely anchor the press.
    The toggle link mechanism and ram have been factory installed. Decide which mode of
    operation you prefer - right or left hand - and install the handle in the appropriate mounting
    hole in the linkage toggle. Be sure to thread the locknut onto the handle first. After the handle
    is screwed into the toggle, lock it in place by turning the locknut to a jam-fit against the tog-
    gle surface.
    NOTE: A positive stop built into the frame blocks handle travel after the ram has passed top
    dead center. No further pressure should be applied, once the stop is reached, to prevent possi-
    ble damage to the press.
    Installation of the Shell Holder
    The shell holder slides into the slotted top of the T-Mag
    ram and is held in place by the integral spring clip.
    To make the shell holder more accessible to your hand,
    turn it slightly to the left if you are right handed; slightly to
    the right if you are left handed. Most reloaders use their
    strongest arm to operate the ram.
    Extra shell holders are available for a wide variety of
    cartridges as indicated in the current annual Lyman
    Catalog.
    Installation and Use of the Priming Arm
    Open the package containing the Lyman Priming Arm.
    It contains a priming arm complete with a large priming
    sleeve and a large, flat primer punch to seat large primers. 
    Figure 6 
    						
    							Should you need to seat small primers, substitute the small
    flat primer punch and sleeve packed separately using the
    enclosed Hex wrench.
    To install, remove the quick release pin from the priming
    arm lug. Position the priming arm as shown in Figure 6.Re-
    insert the quick release pin.
    To use the priming arm, place an unprimed cartridge case in
    the shell holder and a primer (anvil up) into the sleeve of the
    priming punch. Raise the ram to the top of its stroke and push
    the priming arm toward the press. The priming arm will enter
    the slot in the front of the ram and, as the ram is lowered, will
    force the primer into the primer pocket of the case. This opera-
    tion may be done when the cartridge case is being withdrawn from the decapping and resizing
    die, but may be done later if you wish to clean or trim your cases before repriming.
    Changing a Sleeve or Punch
    To change another sleeve size or primer punch, use the hex wrench provided to loosen the
    locking screw on the front of the priming arm, being careful not to lose the spring under the
    priming sleeve. Install the new sleeve and primer punch and retighten the screw.
    Installing the Primer Catcher
    The plastic primer catcher is positioned cupside up, directly under the primer arm lug. Press
    it firmly against the reloading press. Secure the primer catcher to the press by fitting the plas-
    tic retaining bar into the slots provided atop the sidewalls. It will catch and hold spent primers
    that are decapped during the resizing operation.
    Installation and Use of the Primer Feed for “T” Mag Presses (Optional)
    Your automatic primer feed can be equipped with both large and small primer tubes. Small
    rifle and pistol primers fit the small tube while large rifle and pistol primers fit the large tube.
    The careful use of these tubes will speed the priming operation but remember to use extreme
    care when handling primers.
    The first step in installation is to place the primer feed body between the lugs of either loca-
    tion in the turret of the press as shown in Figure 7. Fasten in place using the furnished set
    screws.
    The primer feed body must be adjusted up or down until the drop tube is directly over the
    priming punch sleeve when the priming arm is in the back position (see Figure 7). When this
    adjustment is correct, the priming arm will pick up a single primer and, when pressed into the
    ram, carry it into priming position. The remainder of the primers will be kept in the primer
    tube by the cutoff pin.
    When using the auto-primer feed with the T-Mag press the priming arm must be disen-
    gaged from the primer feed body to turn the turret past the priming station. To return to the
    priming station, the primer arm must be pressed forward, toward the ram, to clear the primer
    feed housing as it is rotated into position.
    Filling the Primer Tube
    To fill the primer tube, first insert one of the two supplied cotter pins through the hole in
    the side of the primer tube. Spread the ends of the cotter pin slightly to keep it from falling
    out. Next, place your primers anvil-side down in a small flatbottomed tray or dish.
    Figure 7
    T-Mag II (continued) 
    						
    							Force the slotted end of the tube down over each primer. The cotter pin will prevent the
    primers from dropping from the open end of the tube when you turn it over.
    Fill the tube completely, press the bushing (“0 ring”) end firmly into the primer feed body
    and remove the cotter pin. One of the red plastic sleeves supplied should be slipped over the
    open end of the primer tube to prevent injury should your face or arm strike to top of the
    primer tube.
    Lubrication and Care of Your Press
    Before using your press, apply a light film of powdered graphite to the bearing surfaces of
    all moving parts. Pay particular attention to the sides of the ram. Thin oil may also be used for
    this purpose but graphite is more desirable. If your press is to be used in a damp area, it is rec-
    ommended that you also protect unpainted surfaces with a thin film of oil.
    Turret Support
    The screw at the rear of the press serves as a support to the Turret when maximum pressure
    is applied. Rotate the Turret and verify for clearance between the Turret Support screw and
    the Turret. The screw should be adjusted so that it is slightly (about 1/64) below the bottom
    edge of the Turret but not touching the Turret itself. Adjustment can be made by loosening
    the locknut and turning the screw until the proper gap is achieved. Tighten the locknut. Rotate
    the Turret and check for clearance. If the user feels further adjustment is required, the screw
    can be moved in 1/8 turn increments until a satisfactory gap is accomplished.
    A handy multi-purpose press/die accessory wrench is provided for making this adjustment.
    T-Mag II(continued)
    CAUTION
    Use extreme care when handling primers. Never mishandle any primer feed that mal-
    functions. Do not do anything that could cause a primer to explode when cleaning a
    jam. Keep your work area clean, occasionally wiping dust with a damp rag.
    Visit our complete Lyman website at 
    www.lymanproducts.com 
    						
    							INSTRUCTIONS FOR INDEXING AND REMOVING
    THE TURRET OF YOUR T-MAG 11 PRESS
    Your T-Mag II Press is supplied with a turret handle (item #2) which can be used for index-
    ing or removing the turret from the reloading press. For easy indexing. insert the turret handle
    into one of the two holes in the turret (item #3) and turn as desired. To change or remove the
    turret, secure the press to a table or other fixed surface. Insert the turret handle through the
    cross hole in the turret shoulder bolt (item #1). Using the handle as a wrench, loosen the bolt
    in a counterclockwise direction and remove it from the turret. Lift the turret straight off the
    press frame. When dies are installed in the turret it is necessary to rotate the turret slightly so
    that the turret handle can be positioned between two dies. The turret shoulder bolt can then be
    removed by turning both the bolt and turret. To reattach the turret, simply reverse the forego-
    ing steps.
    1Turret Shoulder Bolt 7991458
    2Turret Handle 7991461
    3Turret 7726153
    4Auto Primer Set Screw (4)7726115
    5Locating Turret Collar 7991459
    6Press Frame 7990501
    7Toggle Pin 7726215
    8Ram 7726212
    9Ram Pin 7726213
    10 Shell Holder Clip 7726109
    11 Universal Priming Arm 7728036
    12 Handle/Ball Assembly 799050313 Quick Release Primer Arm Pin 7729230
    14 Power Link (2) 7991463
    15 5/8-18 Handle Jam Nut 7726218
    16 Toggle Pin Clip (4) 7726220P
    17 Toggle 7726210
    18 Turret Support Screw & nut 7990505
    Not Shown:
    Press/Die Wrench 7990116
    Primer Catcher 7726420 Key  Part Description  Part # Key  Part Description  Part #
    T-Mag II(continued) 
    						
    							Parts List for Lymans Universal Primer Arm and
    Auto-Primer Feed Assemblies
    1Large Primer Punch 7992922
    2Small Primer Punch 7992924
    3Large Primer Sleeve 7992918
    4Small Primer Sleeve 7992919
    5Primer Sleeve Spring 7992920
    6Set Screw 7992932
    7Primer Arm Complete 7728036
    1Large Primer Feed Tube7412053
    2Small Primer Feed Tube7412052
    3Cotter Pins (2) 7990050
    4Primer Feed Body 7726128
    5Primer Punch Stop 7992900
    6Compression Spring 7992927
    7Set Screw 2992929
    Primer Feed Complete 7729050
    Universal Primer Arm
    Crusher/T-Mag Auto Primer Feed Key  Part Description  Part #
    Key  Part Description  Part #
    Visit our complete Lyman website at 
    www.lymanproducts.com 
    						
    All Lyman manuals Comments (0)

    Related Manuals for Lyman The Mag 2 Press Instructions Manual