Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Administration For Network Connectivity Instructions Manual

QSIG 
371
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
B  Private Networking
Setting Up QSIG
Begin
Steps
1
Verify with your sales representative or project manager what QSIG capabilities 
the system should have. The following capabilities apply:
2Determine whether the system is using ISDN-PRI, ISDN-BRI, or ATM for the 
QSIG network connections. Your sales representative or project manager should 
know this. (If the system is using ATM trunking for QSIG, see...

QSIG B  Private Networking
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
372
3Enter display system-parameters customer-options on the command line 
of your system administration screen.
4On page 1, verify fields as follows:
~G3 Version field is V8 or later.
5If the system is using ATM for QSIG, go to page 2 and verify the following field:
~Async. Transfer Mode (ATM) Trunking field is y.
6On page 3, verify fields as follows:
If the system is using ISDN-BRI for...

QSIG 
373
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
B  Private Networking
10Administer or check the QSIG ISDN trunk group(s) (PRI or BRI) connected to 
the DS-1 or BRI circuit pack (see Appendix A). Check for the following field 
entries on Page 1:
•Group type - isdn
•Supplementary service protocol- b or d where: 
(For Supplementary Services with or without Rerouting) 
•Outgoing Display? - y
•QSIG Value-Added Lucent - y
On Page 2 (Also for Supplementary Services...

QSIG B  Private Networking
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
374
Setting Up QSIG 
Supplementary 
Services
Begin
Steps
1
Administer or check the ISDN Numbering - Public/Unknown screen (see 
Appendix A).
2Administer or check the ISDN Numbering - Private screen (see Appendix A).
3Administer or check the Signaling Group screen (see Appendix A). Check for the 
following field entries to ensure proper operation of Call Completion:
•Supplementary Service...

QSIG 
375
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
B  Private Networking
Call Completion
In addition to the Basic QSIG Supplementary Services administration described 
above, complete the following administration:
•On the Trunk Group screen, page 1, set the Supplementary Service Protocol field 
to b and administer the trunk for Call Independent Signalling Connections.
Transfer into Voice Mail
In addition to the Basic QSIG Supplementary Services administration...

QSIG B  Private Networking
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
376
Setting Up QSIG VALU 
Call Coverage 
Begin
Steps
1
Enable the QSIG Basic Supplementary Services on the Customer Options screen, 
page 6, described above.
2Enable (enter y) Value-Added Lucent (VALU) on the System-Parameters 
Customer-Options screen, page 6, as described above.
3On a Trunk Group screen, enter y in the QSIG Value-Added Lucent field, page 1, 
and sent b in the supplementary...

QSIG 
377
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
B  Private Networking
•Maintain SBA at Principal - Enter y to allow the user who originally 
receives the call to have simulated bridged appearance capability in the 
event the coverage point(s) are unavailable.  This capability allows the 
user to break into the call before it is answered by a coverage endpoint.
Note:If Maintain SBA at Principal is enabled (y), then Path Replacement 
is disabled.
5Define the...

QSIG B  Private Networking
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
378
See the Octel Serenade documentation for Serenade administration.
Begin
Steps
1
(Local node message center switch only) Complete the Processor Channel 
Assignment screen (see Appendix A).
2(Local node message center switch only) Complete the Message Waiting 
Indication Subscriber Number Prefixes screen (see Appendix A).
3(Local node message center switch only) Complete the Station screen...

QSIG 
379
Administration for Network Connectivity
555-233-504— Issue 1 — April 2000 CID: 77730
B  Private Networking
QSIG Interactions
Call Forwarding 
(Diversion)The interactions that apply to the standard DEFINITY ECS Call Forwarding features 
also apply to Call Forwarding (Diversion) with QSIG. The following are additional 
interactions.
•Alternate Facilities Restriction Levels
The AFRL of the original call is the AFRL used for Call Forwarding with 
Reroute.
•Authorization Codes
Call Forwarding with...

QSIG B  Private Networking
Administration for Network Connectivity
CID: 77730 555-233-504 — Issue 1 — April 2000
380
Call Transfer •Call Forwarding (Diversion)
When a call is forwarded and transferred or transferred and forwarded, the 
forwarding indication displays to the caller until the call is answered. This display 
includes the trunk group name and word “forward.” When the call is answered, 
the word “forward” is removed and the name and number of the answering party 
displays.
•Distributed...