Loewe Modus L42 Plasma Operating Instructions

							11 -
First installation
Remote control
Batteries
To insert or change the batteries, press on the arrow. Slide the battery compart-
ment cover downwards and remove it. Insert LR 03 alkaline-manganese batteries 
(AAA) and ensure that the + and - ends are positioned correctly.
Then push the cover back on from the bottom.
Note on disposing batteries:
The batteries provided contain no harmful materials such as 
cadmium, lead or mercury.
Regulations concerning used batteries stipulate that batteries 
may no longer be thrown out with the household rubbish. 
Deposit any used batteries free of charge into the designated 
collection containers set up at commercial businesses. 
Setting up the remote control for operating the TV
Press the TV button
How to operate other Loewe equipment is described on page 39.
Connection
Power mains
Remove the cover for the connections.
Connect the TV set to a 220-240V/50- 60 hertz power outlet. For the LCD sets, 
plug the small plug of the mains cable into the mains socket on the rear of the 
TV set; plug the large mains plug into a mains socket. For Plasma sets, the mains 
cable is permanently connected to the set.
Antennas
Plug the antenna plug of your antenna/cable system or the room antenna for DVB-
T into the ANT-TV socket (Tuner 1).
ANT-TVANT-SAT220-240V~
50/60Hz
TV
R
Xelos A32/37
        Modus L32/37
89352.001SERVICEVGA/XGA HDTV IN AUDIO OUT
AUDIO DIGI TA L
INLR
OUT AUDIO IN
L
SD/HD-COMPONENT IN
C/PrrY C/PbbR C
AV  2
RGB / YUV (                    ) AV  1 ANT -TVANT -SAT
13/18 V        /350 mA
5 V        /80 mAHDMI  DVI(        )
Xelos A42
Modus L42
ANT-TV ANT-SAT220-240V~
50/60Hz
Xelos A 26
AAA  LR03
AAA  LR03
BA32789_021XelosModusRel_5_GB.in11   11BA32789_021XelosModusRel_5_GB.in11   1115.01.2007   16:53:5915.01.2007   16:53:59
 
						

							- 12
First installation
If the reception conditions are good, then a room antenna may be used for DVB-T. 
Passive and active room antennas are available on the market. The power is sup-
plied for an active antenna via the antenna connection. For automatic programming 
or in “TV Menu – Connections – Antenna DVB – Antenna DVB-T,“ the distribution 
voltage (5 volts) is to be set correspondingly.
It may be practical to use a nondirectional antenna. If the location is outside the 
normal transmitting range, then a unidirectional antenna may also be used to 
improve the reception quality.
You can find out more on the digital stations that can be received in your area at 
your specialist dealer.
If a set was retrofitted with a PIP tuner or if this is already integrated in a set with a 
digital recorder, then plug the antenna into the antenna input of the PIP tuner and 
connect the PIP tuner output with the ANT-TV socket (Tuner 1). See illustrations on 
page 6/7.
Set-specific equipment and retrofitting options for PIP and satellite tuners, see 
pages 44 and 45.
If a Digital Satellite Tuner 1 has been retrofitted, connect your satellite antenna 
system to the ANT-SAT socket.
If a Digital Satellite Tuner 2 has been retrofitted, connect one antenna cable each, 
for example from the antenna switch or from the twin LNC, to both SAT sockets.
 
When laying the cable, use the cable clips affixed beneath the TV set.
Replace the connection cover on the TV set.
Use of the binders for Xelos A42 and    
Modus L 42
The enclosed binders are intended 
for holding the connection cables 
together and fastening them to the 
rear panel. 
The binders can be opened again by 
pressing on the binder latch.
Using the conditional access module
In order to be able to receive encrypted digital stations, a Conditional Access 
module (CA-module (1) and a Smart Card (1, if necessary, must be inserted into the 
corresponding slot of your TV set. You can find the Common Interface slot (CI-Slot) 
on the back of your TV set, see the illustration on pages 5 –7.
1.  Make sure the TV set is switched off with the mains switch on the set.
2.   First push the smart card into the CA module as far as it will go. Insert it so 
that the side with the 
golden contact chip faces 
the side of the module 
printed with the supplier‘s 
brand logo. Printed arrows 
indicate how to insert the 
card. Also follow the instal-
lation instructions included 
with the smart card.
3.   Slide the CA module 
(1 carefully into the slot with the 
contact side facing the front. When you are standing 
in front of the TV set, the logo on the CA module 
must face the rear.
  Make sure the module is not twisted in the process. 
Do not use force. 
  When the module locks, the eject button is pressed 
outwards.
(1  The CA module and the smart card are not included 
in the scope of delivery for this set; you can usually 
obtain them at your specialist dealer.
Switching on
Press the mains switch. The indicator lamp on the set now turns 
red (standby mode). 
Switch on the set using the switch integrated in the indicator. 
The indicator on the TV set lights up and turns green (indicator 
lamp).
Contact side
Eject button 
CA moduleCI-Slot
)
BA32789_021XelosModusRel_5_GB.in12   12BA32789_021XelosModusRel_5_GB.in12   1215.01.2007   16:54:0315.01.2007   16:54:03
 
						

							13 -
First installation
Automatic programming
Automatic programming of the TV set is started the first time you switch it on. Follow 
the menus.
Settings can be selected by pressing one of the directions ...
... and confirm your settings by pressing OK. You then go to the 
next menu. 
Back to the previous menu.
1.  First you have to select the menu language. 
2.  By pressing the OK button, you can call the menu “Connect antenna cable(s)“. If 
you want to receive digital stations via satellite, then choose “DVB-S“ - confirm 
using the yellow coloured key. If you also want to receive digital terrestrial 
stations (DVB-T), then select “DVB-T“. 
Also select “Antenna/cable (analo-
gue)“ - this way the standard analo-
gue stations can also be searched for 
and saved. If you can receive digital 
stations from the cable network, then 
select “DVB-C“ using the yellow 
coloured key. 
3.  For the country-specific station sorting and for presettings for DVB-T and DVB-C, 
enter the location at which the TV set is operated.
4.  If you have selected “DVB-T“, you then reach the menu “Antenna 
DVB-T“. If you use an active antenna, then select “yes (5V)“.
5.  If you have selected “DVB-C“, you generally leave the symbol rates and modulati-
on types unchanged. 
If other symbol rates are used in your cable network for broadcasting, enter the 
values with the numeric buttons of the remote control. If only one symbol rate is 
used, enter the same value for both symbol rates. If other modulation types are 
used for broadcasting in your cable network, select them in the menu. If only one 
modulation type is used, select “none“ for modulation type 2. 
If necessary, ask your specialist dealer about the necessary settings for your cable 
network.
6.  In the “Select satellite installation“ menu, make the selection that corresponds to 
your satellite antenna installation.
Note: If you have any questions on how your satellite antenna installation is 
configured and on the antenna settings, consult your antenna installer or your 
specialist dealer.
7.  Select the satellite the antenna is directed at, such as ASTRA1.If you only receive one satellite...
8.  In the following menu, specify whether the station search should take place in the 
high and low band (“Yes“) or only in the low band (“No“).
Note: For most satellites, a station search is required in both bands.
9.  For the low band and high band, the standard frequencies 9750 MHz (9.75 GHz) 
and 10600 MHz (10.6 GHz) are preset. 
If your satellite antenna is equipped with an LNC (LNB) with a divergent oscillator 
frequency, specify the corresponding frequency for low and high band respective-
ly.
Note: The correct display of the received frequencies in the “TV menu – Settings 
– Channels – Manual adjustment“ depends upon this setting.
10. You should receive a picture with sound with the settings previously made (only 
for ASTRA 1 and HOTBIRD). Then press OK.
11. In the “Pre-programming“ menu, select the factory-set pre-programming to 
programme the satellite stations quickly.
To ensure all stations that can be currently received are searched for and saved, 
select “No“ at this point.
Symbol rates: The standard symbol rates 22000 and 27500 are preset. If you 
would like to receive stations with different symbol rates, specify the correspon-
ding values here using the numeric buttons on your remote control.
12. Press OK to obtain an overview of the settings with which the automatic pro-
gramming is to take place.
13. Press the OK button again and the station search will start. The TV set searches 
for, sorts and saves all the TV stations that can be received, according to your 
settings and the antennas connected.
14. When the TV stations are saved, you will receive a corresponding message.
15. Press the OK button and the set then searches for the radio stations.
16. The TV set searches for, saves and sorts all radio stations which can be received 
with your antenna system. 
17. Then log on your video equipment, decoder and audio system using the connec-
tion wizard and connect these to the TV according to the connection diagram 
displayed. If you want to connect other equipment later, you can find information 
as of page 32.
You can repeat the initial installation at any time, e.g. after moving house. Call the 
index using the INFO button (in the TV mode, if no menu is opened). Select the index 
item “Repeat initial installation“ (you will find this listed separately before the letter 
A). Press OK to start the initial installation.
Note: For DVB-T stations in UK the stations are tied to “Logical Channel Numbers” 
– “LCN” and sorted from 1–799. Digital station without “LCN” are stored from 800 
onwards. Analogue stations are stored from1001.
Station sorting
Note: not with DVB-T stations in UK.
You can change the station sorting that was carried out automatically later at any 
time, see “TV menu – Settings – Stations – Change stations“.
Initial installation
Connect antenna cable(s)
Proceed
BackOKConnect/disconnect
Antenna cable(s) for:  to antenna socket(s):
Antenna/cable (analogue)  ANT TV
DVB-T ANT TV
DVB-C ANT TV
DVB-S ANT SAT
BA32789_021XelosModusRel_5_GB.in13   13BA32789_021XelosModusRel_5_GB.in13   1315.01.2007   16:54:0415.01.2007   16:54:04
 
						

							- 14
First installation
Directing DVB-T antenna
Note: not with DVB-T stations in UK.
If you use a room antenna to receive one or more DVB-T stations that have picture 
and sound interference, then you should change the location of where the antenna 
is set up. To help you direct your antenna or to help you determine the most suitable 
location to set up the antenna, your TV set has a display for the signal quality C/N 
and the signal strength Level.
Consult your specialist dealer to find out which channels and frequency bands (VHF 
or UHF) are used to broadcast the digital TV stations in your area.
On any one channel, several digital stations are broadcast.
Select a TV channel
1.  Call the “TV menu“ via the MENU button.
2. Use  to select “Settings“, then use  to select the menu line underneath.
3.  Select “Stations“, then use  to select the menu line underneath.
4.  Select “Manual adjustment“ and call the menu using OK (not possible for 
MHEG-5 device versions x27/28). 
5.  For digital stations, select “Signal source – DVB-T“.
6. Use the numerical buttons to specify the corresponding channel number.
  Depending on the channel selected and country, the system automatically sets 
the corresponding bandwidth of 7 or 8 MHz. You should only change the band-
width under special circumstances - if the channel raster in your area is different 
from the standard.
When you receive a digital station, the system displays the signal quality  
C/N via a bar/numeric value and the signal strength via Level. The antenna‘s 
direction or position is best when the largest values possible are displayed (long 
bar) for the signal quality and signal strength.
7.  Direct the antenna so that the largest numerical value/bar size is reached.
8.  If no signal is found in the channel set, you can start the frequency search run 
by pressing the blue coloured key within the band selected.
9.  Check the other channels one after another on which digital stations are broad-
cast terrestrially in your area.
  For the weakest station, direct the antenna so that the maximum numerical 
value/bar size is achieved.
10. After you position or direct the antenna, we recommend to search for all the 
stations using the “Search wizard“ (TV menu – Settings – Stations – Search 
wizard).
INFOEND
Manual adjustment                 ...Language
Parental lock StationsTimer functions TV menu
Settings
END
Manual adjustment
Signal source
Channel
Frequency
Name
Bandwidth
C/N  96DVB-T
E 05
177.50 MHz
Test
7 MHz
Level  99DVB-CAntenna/cable (analogue
Daily operation
Switching on/off
Your TV is equipped with an eco-standby power supply unit. On standby, the 
power consumption drops to low power. If you want to save even more electricity, 
switch the set off with the mains switch. However, please bear in mind that EPG 
data (electronic programme guide) will be lost, and programmed timer recordings 
will not be performed by the TV.
Switching off
If the TV set is switched on, you can switch it to standby using 
the On/Off button O on the remote control or by using the 
indicator field on the set. The red lamp on the TV set lights up. 
If the lamp is orange, a timer recording is being made, EPG data 
is being captured or radio operation without screen display is 
active.
Switching on the TV set
From standby, it is best to switch the set back on using the 
On/Off button O or by using the numeric buttons of the remote 
control (0 – 99). 
Or use the switch integrated in the indicator on the set. 
The green indicator on the TV set lights up.
Or switch on the TV set with OK, you can then see the station 
list and select a station. 
Switching on the radio
With the RADIO button on the remote control 
or 
with R on the control ring of the TV set, you can switch on the 
radio.
If you switch off the TV set using the mains switch on the set, the indicator no 
longer lights up. 
If the TV set is switched off via the mains switch, then you have to first switch it 
into standby mode via the mains switch and then switch it on with the remote 
control or by using the indicator window on the set.
)
)
)
BA32789_021XelosModusRel_5_GB.in14   14BA32789_021XelosModusRel_5_GB.in14   1415.01.2007   16:54:0615.01.2007   16:54:06
 
						

							15 -
Daily operation
Changing stations
... with the P+/P- buttons on the remote control
        Stations up/down
When changing, the station display is visible for a few seconds.
If additional languages are broadcast with DVB stations, then the set displays 
the language/sound selection under the station display. Call the language/sound 
selection by using the green coloured key and select using .
... with the numeric buttons of the remote control
The set has a dynamic memory with 1680 station memory locations. If up to 9 
stations are stored, you only need to enter one digit; up to 99 stations, two digits 
are needed; up to 999 stations, three digits are needed (refer to the station list to 
see how many stations have been stored).
1-digit stations 
Press buttons 0 – 9 for one second, and the station 
changes instantly.
Or press button 0 – 9 briefly, the station then changes 
after 2 seconds (the station changes immediately when 
only 9 stations are saved).
2-and 3-digit stations
After briefly pressing the first numeric button(s), keep 
the last numeric button pressed for one second, the 
station then changes immediately.
Or press all numeric buttons briefly, the station then 
changes after 2 seconds (the station changes immedia-
tely if up to 99 or 999 stations are saved).
4-digit stations
Press the four numeric buttons briefly, the channel then 
changes immediately.
Call last viewed station (for DVB-T stations in UK)
You can switch back and forth quickly between two stations 
using this button.... via the station list
Use OK to call the station list
Select the station (if possible, the selected station will be dis-
played as a small picture)
or ...
... select with numeric buttons
call selected station
Blue coloured key: sort alphabetically/according to bouquets/
numerically
For an alphabetical display: Enter letters with the numeric button (like on a mobile 
phone keypad), select with  and call with OK.
For bouquet display (sorting according to broadcasting chains, only for DVB sta-
tions, not for DVB-T stations in UK): Enter bouquet number, select with  
and call with OK.
Digital DVB-T stations are indicated by , DVB-C stations by  and DVB-S 
stations by . Encrypted stations are additionally indicated by .
Ask your specialist dealer about decoders or the use of a CA module and a Smart 
Card for the reception of encrypted stations.
09ENDOK
  6  3SAT
  7  S–RTL
  8  N–TV
  9  DSF
10   TM3  
11 PRO7
12 RTL 2
13 WDR 3
14 BR
15 HR
16 MDR 3
17 N 3 COMP. IN
 HDMI/DVI
 VGA
 AV S
 DVD
 VCR
    0  VIDEO
    1  ARD
    2  ZDF
    3  SAT.1
    4  RTL
    5    VOX
OK
Station list                                Numerical
Switch to ...                      Scan stations 21:00 - 21:45   Eifellandschaft
...     Select station        Change stations
Change sorting
long
short short long
     all short
ENDOK
OK
az
 CNN INT.
 CAM
 DELUXE
 DSF
 EUROSPRT
 HOT
 HR
 
 KIKA COMP. IN
 HDMI/DVI
 VGA
 AV S
 DVD
 VCR
 ARD
 
 BR-ALPHA
 BR3
       
Station list                             Alphabetical
Switch to ...                      Scan stations 21:00 - 21:45   Eifellandschaft
...     Select letter        Change stations
Change sorting
41  ZDF  Eifellandschaft                   21:00 – 21:45Language/sound selection
(
(
(
BA32789_021XelosModusRel_5_GB.in15   15BA32789_021XelosModusRel_5_GB.in15   1515.01.2007   16:54:0915.01.2007   16:54:09
 
						

							- 16
Daily operation
Set the bass tones by using .
If you want to make other sound settings, move up with  to 
“Bass“ and select with , e.g. “more...“. You can also move up 
further to “Sound“ by using  and select other settings in the TV 
menu (such as picture settings).
Use OK to call additional sound settings. 
Select the sound setting using , e.g. “Auto volume“ 
and ...
... use  to select the auto volume option. 
Use  to select “on“ and activate the auto volume.
Press the END button to hide the menu.
Apart from the TV menu shown here, other menus can be opened in TV mode as 
follows: 
Call the Sound menu directly.
Quick calls for Image+
✳, teletext subtitles, personal text pages, 
headphone volume, scan stations and to move the picture up and 
down.
Green coloured key: Call standard settings for picture and 
sound.
Using the volume control, you can also open other sound settings, 
such as Sound via, Sound adjustment, Sound effects and Loud-
ness. 
The key  or OK must be pressed for the duration of the volume 
display for this.
Basics about the Menu operation
Menus are called via the MENU button or via the button for special menus and 
can be hidden by using these buttons or by using the END button. The menu is 
displayed in the bottom section of the screen. At the top, you can see additional 
information for the menu point selected. In the menus, navigate by using the cur-
sor . You can make settings by using . When you exit the menu, 
the settings are adopted.
Example of the menu operation
We shall demonstrate how to navigate with the menus using the TV menu as an 
example. You can see which buttons you can use in the dark blue field on your TV 
set.
Open TV menu (in TV mode).
Select the function in the TV menu, e.g. “Sound“ (for sound 
settings). Use  to move the menu points displayed on the 
right into the dark blue field; use  to move the menu points 
displayed on the left. 
Select the sound function below with  or OK; you will then 
see a list of the sound settings.
In the sound settings, also select the function with , e.g. 
“Bass“ (for increasing or reducing the bass tones).
To set the bass tones, use  or OK to select the setting bar 
underneath.
Treble            ...
INFOENDTV menuSettings
Connections
Recording
SoundPicture
INFOEND more ...
Bass TrebleTV menu
Sound4
INFOEND more ...
TV menu
Sound
Treble Bass
 6
INFOENDBassTV menu
6 Sound
INFOENDmore ...
Treble  BassTV menu
SoundOK
INFOENDAuto voLoudspeaker soundHeadphone volume TV menu
Stereo              ...Sound
Headphone sound Bass
INFOENDAuto volumeTV menu
onSoundoff
Picture adjustment        ...
INFOENDSettingsConnectionsRecordingSound TV menuPicture
Picture
Here you can adjust among other things: Contrast, colour, brightness, 
picture adjustment, sharpness, picture format. 
INFOENDAV audio signal Maximum volumesound
Auto volumeTV menu
off              ...Sound
Balance
INFOENDAuto volumeTV menu
offSoundon
(
BA32789_021XelosModusRel_5_GB.in16   16BA32789_021XelosModusRel_5_GB.in16   1615.01.2007   16:54:3415.01.2007   16:54:34
 
						

							17 -
Daily operation
For the info system ...
For each menu point, an info text is displayed at the top of the picture to help you 
with the setting. This saves you from having to refer back to the operating instruc-
tions. We shall demonstrate this using the station search option as an example:
Call the TV menu.
Select “Settings“.
In this example, you can see the options available after “Settings“. 
If you want to search for new stations, for example, use  to 
select “Stations“ in the line below. 
The info text indicates which settings you can make in “Stations“.Use  to select the line below, for example “Search wizard“.
The info text explains how you are to proceed.
Upon delivery, the TV set is configured so that the info texts are always displayed 
(Automatic info “yes“). In this case, you can hide the info texts by using the INFO 
button.
You can also configure the TV set so that you call the info texts when needed by 
using the INFO button (Automatic info “no“). You can find the setting to switch 
the automatic info option on or off via “TV menu under Settings – Miscellaneous 
– On-screen displays – Automatic info – yes/no“.
INFOEND
Stations                ...TV menu
Settings
Conne ectionsRecording
Sound Picture Settings
Here, you can search for the stations automatically or manually as well 
as set the menu language, timer functions, parental lock, on-screen 
displays, etc.
INFOEND
Search wizard                     ...Timer functions Parental lock Stations
Language Mi TV menu
Settings Stations
The menu contains the automatic station search and the manual station 
setting. You can re-sort stations, enter and change station names and 
delete stations.
INFOEND
Search wizard
Manual adjustment Change stations StationsTV menu
Settings Search wizard
Use this menu to search for stations automatically once certain settings 
have been made.
If you want to search for stations with other than the displayed 
settings, select the Change settings menu.
BA32789_021XelosModusRel_5_GB.in17   17BA32789_021XelosModusRel_5_GB.in17   1715.01.2007   16:54:4815.01.2007   16:54:48
 
						

							- 18
Daily operation
For the index ...
Using the index, you can access many operational functions directly. You can also 
find a great deal of information on technical terms about television. Before the 
alphabetical sorting, you can find the menu language option, the DRM mode 
for reducing screen burn-ins (only for TV sets with a plasma screen), the list of 
features integrated into the TV set and the repeat initial installation option. 
Call the index in the TV mode (without any other on-screen 
displays).
Info on the index item selected is visible at the top of the picture. If the OK symbol 
is displayed in the line selected, you can use the OK button to access the menu 
directly and carry out settings or selections.
This is how to select the index item:
Enter the first letter using the numeric buttons on the remote 
control (like on a mobile phone keypad);
or
use  to go to the previous/next letter,
or
use P+/P– to scroll up or down through the pages
and use  to go from line to line.For example, you want to have the TV set switch off automatically: 
Select the index item “Switch off“ – “Automatic“.
Use the OK button to call “Switch off“ – “Automatic“.
The corresponding menu “Timer functions“ is displayed (in the TV menu – Set-
tings). You can now choose between “Switch off today only” and “Switch off daily“ 
and enter the time.
a z 
END OK 
OK 
P+ 
P–   
Index  You can select your language for operating the TV set. Language
DRM (Digital Refresh Mode)
Integrated features
Repeat initial installation
*
Access code
Active window (PIP)
Automatic channel programming (ACP)
Activate     Previous/next letter 
...     Select letter           Page 
						

							19 -
Setting the sound
Volume and other frequently used sound settings
Setting the volume
by using  or OK, you can call other sound settings ... 
and select using  ...
use  for the related selection/setting...
... and use  to make the selection/setting there.
Sound adjustment allows you to adjust the sound characteristics to the station‘s 
sound. The Sound effects settings allow you to expand a Dolby Pro Logic Signal to 
a virtual surround signal by using “Dolby Virtual“; by using “Panorama“, you can 
enhance the foundation of the stereo sound virtually for the loudspeakers. 
Sound off/on
Sound off;
Sound on: Press button again or adjust volume.
Other sound settings:
Call the Sound menu
use  to select the sound function to be set and use  for 
the related selection ...
and use  to select/set.
Sound settings: Treble and bass. Different menu items are displayed depending on 
the connected audio device (AURO, hi-fi amplifier). Under “more ...“ you will find 
the sound selection for loudspeakers and headphones, auto volume, headphone 
volume, AV audio signal, maximum volume and balance.
Picture settings
Open the TV menu
Select Picture with  and selection with .
Use to mark image functions to be set. 
Use  for the related selection/setting...
... and use  to set/select.
Picture settings: Picture adjustment, Contrast, Colour, Brightness and Sharpness. 
Under “more ...“, you can find settings for Image+
✳, Picture format, Move picture 
up/down, Auto format, Film quality improvement DMM✳ and DRM✳ (Digital 
Refresh Mode).
Direct control on TV set
On page 4, you can find illustrations of the control units located on the set.
Switching station on the TV set
Station up: with the button +
Station down: with the button –
Switching the radio on/off or switching over to the radio
Press R to switch the radio on or off.
Additional functions via the menu
In the radio or TV operating modes, you can make settings for Volume, Brightness, 
Contrast, Picture format and Stations. “Service“ is intended for the customer 
service department.
use M  to call the menu
use – or + to select the function to be set
use R for the related setting/selection
use – or + to set/select.
Use M to move one level up; you can use – or + to select other functions.
Daily operation
Volume             ...24
normalLoudness Sound adjustment
Sound effects
VoVolume
PopClassic Sound adjustment
Speechnornormal
Sound off
Sound on
INFOENDmore ... SoundBass Treble4
INFOENDSound
Bass
6
Picture adjustment        ...
INFOENDSettingsConnectionsRecordingSound TV menuPicture
INFO END Colour
6 Picture
TV menu
Operating modeContrastPicture foDirect control on TV set
TVVolume Brightness
Volumeg modeContrastBrightnessPicture formatStatDirect control on TV set
24
VolumeDirect control on TV set18
Sound adjustment VolumeSound effectsLoudness 24
)(
)(
)(
(
(
)
)
BA32789_021XelosModusRel_5_GB.in19   19BA32789_021XelosModusRel_5_GB.in19   1915.01.2007   16:55:0515.01.2007   16:55:05