Loewe Individual 26 Lcd Operating Instructions

							11 -  
First installation
If a set was retrofitted with a PIP tuner or if this is already integrated in a set 
with a digital recorder, then plug the antenna into the antenna input of the PIP 
tuner and connect the PIP tuner output with the ANT-TV socket (Tuner 1). See 
illustration on pages 5/6.
Set-specific equipment and retrofitting options for PIP and satellite tuners, see 
pages 44 and 45.
If a Digital Satellite Tuner 1 has been retrofitted, connect your satellite antenna 
system to the ANT-SAT socket.
If a Digital Satellite Tuner 2 has been retrofitted, connect one antenna cable 
each, for example from the antenna switch or from the twin LNC, to both SAT 
sockets.
Handling the fabric hose (optional)
Use the fabric hose for tidy 
laying of the power cables, 
antenna cables or cables of 
other electronic components 
and lay the hose with the cables 
to the connecting sockets. This 
provides you with an elegant 
solution when laying cables. 
The diameter of the fabric hose 
increases when you push it together lengthwise (see illustration). This makes it 
easier for you to push through cables with plugs.
You can obtain the fabric hose as an accessory from your Loewe dealer or Loewe 
Customer Service.
Use of the binders
The enclosed binders are 
intended to bind the connect-
ing cables together and fix the 
cables to the mount of the table 
stand (see figure). 
By pressing on the closure of 
the binder, it can be opened 
again.
Replace the connection cover on the TV set.
Using the Conditional Access module
In order to be able to receive encrypted digital stations, a Conditional Access 
module (CA-module (1) and a Smart Card (1, if necessary, must be inserted into 
the corresponding slot of your TV set. You can find the Common Interface slot 
(CI-Slot) on the back of your TV set, see the illustration on pages 5/6.
1.  Make sure the TV set is switched off with the mains switch on the set.
2.   First push the Smart Card into the CA-module as far as it will go. Insert it so 
that the side with the golden 
contact chip faces the side 
of the module printed with 
the supplier‘s brand logo. 
Printed arrows indicate how 
to insert the card. Also follow 
the installation instructions 
included with the Smart 
Card.
3.   Push the CA module carefully into the slot contact 
side first. When you are standing in front of the TV 
set, the logo on the CA module must face the rear.
  Make sure the module is not twisted in the process. 
Do not use force. 
  When the module locks, the eject button is pressed 
outwards.
(1   The CA-module and the Smart Card are not included 
in the scope of delivery of this set; you can usually 
obtain them at your specialist dealer.
Switching on
Press the mains switch, the red indicator on the set now lights 
up (standby mode). 
Switch on the set using the switch integrated in the indicator. 
The green indicator on the set now lights up (for further oper-
ating options see page 13).
Contact side 
Eject button 
CA moduleCI-Slot
 
						

							 - 12
First installation
Automatic programming
Automatic programming of the TV set is started the first time you switch it on. 
Follow the menus.
Settings can be selected by pressing one of the directions ...
... and confirm your settings by pressing OK. You then go to 
the next menu. 
Back to the previous menu.
1.  First you have to select the menu language. 
2.  By pressing the OK button, you can call the menu “Connect antenna 
cables(s)“. If you want to receive digital stations via satellite, then choose 
“DVB-S“ - confirm using the yellow coloured key. If you also want to receive 
digital terrestrial stations (DVB-T), 
then select “DVB-T“. Also select 
“Antenna/cable (analogue)“ - this 
way the standard analogue stations 
can also be searched for and saved. 
If you can receive digital stations 
from the cable network, then select 
“DVB-C“ using the yellow coloured key. 
3.  For the country-specific station sorting and for presettings for DVB-T and 
DVB-C, enter the location at which the TV set is operated.
4.  If you have selected “DVB-T“, you then reach the menu “Antenna DVB-T“. If“DVB-T“, you then reach the menu “Antenna DVB-T“. IfDVB-T“, you then reach the menu “Antenna DVB-T“. If 
you use an active antenna, then select “yes (5V)”.
5. If you have selected “DVB-C“, you generally leave the symbol rates andIf you have selected “DVB-C“, you generally leave the symbol rates and 
modulation types unchanged. 
  If other symbol rates are used in your cable network for broadcasting, 
enter the values with the numeric buttons of the remote control. If only one 
symbol rate is used, enter the same value for both symbol rates. If other 
modulation types are used for broadcasting in your cable network, select 
them in the menu. If only one modulation is used, select “none“ for modula-
tion type 2. 
  If necessary, ask your specialist dealer about the necessary settings for your 
cable network.
6.  In the “Select satellite installation“ menu, make the selection that corre-
sponds to your satellite antenna installation.
  Note: If you have any questions on how your satellite antenna installation 
is configured and on the antenna settings, consult your antenna installer or 
your specialist dealer.
7.  Select the satellite the antenna is directed at, such as ASTRA1.
If you only receive one satellite ...
8.  In the following menu, specify whether the station search should take place 
in the high and low band (“Yes“) or only in the low band (“No“). 
Note: For most satellites, a station search is required in both bands.
9.  For the low band and high band, the standard frequencies 9750 MHz (9.75 
GHz) and 10600 MHz (10.6 GHz) are preset. 
If your satellite antenna is equipped with an LNC (LNB) with a divergent 
oscillator frequency, specify the corresponding frequency for low and high 
band respectively.  Note: The correct display of the received frequencies in 
the “TV menu – Settings – Stations – Manual adjustment“ depends upon 
this setting.
10. You should receive a picture with sound with the settings previously made 
(only for ASTRA 1 and HOTBIRD). Then press OK.
11. In the “Pre-programming“ menu, select the factory-set pre-programming to 
programme the satellite stations quickly. 
To ensure all stations that can be currently received are searched for and 
saved, select “No“ at this point. 
Symbol rates: The standard symbol rates 22000 and 27500 are preset. If you 
would like to receive stations with different symbol rates, specify the cor-
responding values here using the numeric buttons on your remote control.
12. Press OK to obtain an overview of the settings with which the automatic 
programming is to take place.
13. Press  the OK button again and the station search will start. The TV set 
searches for, sorts and saves all the TV stations that can be received, accord-
ing to your settings and the antennas connected.
14. When the TV stations are saved, you will receive a corresponding message.
15. Press  the OK button and the set then searches for the radio stations.
16. The TV set searches for, saves and sorts all radio stations which can be 
received with your antenna system. 
17. Then log on your video equipment, decoder and audio system using the 
connection wizard and connect these to the TV according to the connection 
diagram displayed. If you want to connect other equipment later, you can 
find information as of page 31.
You can repeat the initial installation at any time, e.g. after moving house. Call 
the index using the INFO button (in the TV mode, if no menu is opened). Select 
the index item “Repeat initial installation“ (you will find this listed separately 
before the letter A). Press OK to start the initial installation.
Note: For DVB-T stations in GB the stations are tied to “Logical Channel Num-
bers” – “LCN” and sorted from 1-799. Digital stations without “LCN” are stored– “LCN” and sorted from 1-799. Digital stations without “LCN” are stored “LCN” and sorted from 1-799. Digital stations without “LCN” are stored 
from 800 onwards. Analogue stations are stored from 1001.
Station sorting
Note: not with DVB-T stations in GB.
You can change the station sorting that was carried out automatically later at 
any time, see “TV menu – Settings – Stations – Change stations“.Stations – Change stations“. – Change stations“.
Initial installation 
Connect antenna cable(s) 
Proceed 
Back OK Connect/disconnect 
Antenna cable(s) for:  to antenna socket(s): 
Antenna/cable (analogue)  ANT TV 
DVB-T ANT TV 
DVB-C ANT TV 
DVB-S ANT SAT 
 
						

							13 -  
Switching on/off
Your TV is equipped with an eco-standby power supply unit. On standby, the 
power consumption drops to low power. If you want to save even more electric-
ity, switch the set off with the mains switch. However, please bear in mind that 
EPG data (electronic programme guide) will be lost and programmed timer 
recordings will not be performed by the TV.
Switching off
If the TV set is switched on, you can switch it to standby using 
the ON/OFF button O on the remote control or by using the 
indicator field on the set. The red lamp on the TV set lights up. 
If the orange indicator lights up, a timer recording is being 
made, EPG data is being captured or radio operation without 
screen display is active.
Switching on the TV set
From standby, it is best to switch the set back on using the On/
Off button O or by using the numeric buttons of the remote 
control (0 – 99). 
Or use the switch integrated in the indicator on the set. 
The green indicator on the TV set lights up.
Or switch on the TV set with OK, you can then see the station 
list and select a station. 
Switch on the radio
With the RADIO button on the remote control 
or:
Switch on radio using R on the control ring of the TV set.
If you switch off the TV set using the mains switch on the set, the indicator no 
longer lights up. 
If the TV set is switched off via the mains switch, you have to switch it into the 
standby mode first via the mains switch and then switch it on using one of the 
above mentioned methods.
First installation
Directing DVB-T antenna
Note: not with DVB-T stations in GB.
If you use a room antenna to receive one or more DVB-T stations that have 
picture and sound interference, then you should change the location of where 
the antenna is set up.
To help you direct your antenna or to help you determine the most suitable loca-
tion to set up the antenna, your TV set has a display for the signal quality C/N 
and the signal strength Level.
Consult your specialist dealer to find out which channels and frequency bands 
(VHF or UHF) are used to broadcast the digital TV stations in your area.
On any one channel, several digital stations are broadcast.
Select a TV channel
1.  Call the “TV menu“ via the MENU button.
2. Use  to select “Settings“, then use  to select the menu line under-
neath.
3.  Select “Stations“, then use  to select the menu line underneath.
4.  Select “Manual adjustment“ and call the menu using OK (not possible for 
MHEG-5 device versions). 
5.  For digital stations, select “Signal source – DVB-T“.
6. Use the numerical buttons to specify the corresponding channel number.
  Depending on the channel selected and country, the system automatically 
sets the corresponding bandwidth of 7 or 8 MHz. You should only change 
the bandwidth under special circumstances - if the channel raster in your 
area is different from the standard.
  When you receive a digital station, the system displays the signal quality  
C/N via a bar/numeric value and the signal strength via Level. The anten-
na‘s direction or position is best when the largest values possible are 
displayed (long bar) for the signal quality and signal strength.
7.  Direct the antenna so that the largest numerical value/bar size is reached.
8.  If no signal is found in the channel set, you can start the frequency search 
run by pressing the blue button within the band selected (VHF or UHF).
9.  Check the other channels one after another on which digital stations are 
broadcast terrestrially in your area.
  For the weakest station, direct the antenna so that the maximum numerical 
value/bar size is achieved.
10. After you position or direct the antenna, we recommend to search for all the 
stations using the “Search wizard“ (TV menu – Settings – Stations – Search 
wizard).
INFO END 
Manual adjustment                 ... Language
Parental lock  Stations 
Timer functions TV menu 
Settings 
END 
Manual adjustment 
Signal source 
Channel 
F r equen cy 
Name 
Bandwidth 
C/N  96 DVB-T 
E 05 
177.50 MHz 
T es t 
7 MHz 
Level  99 DVB-C Antenna/cable (analogue) 
 
Daily operation
 
						

							 - 14
Changing stations
... with the P+/P- buttons on the remote control
Stations up/down
When changing, the station display is visible for a few seconds.
If additional languages are broadcast with DVB stations, then the set displays 
the language/sound selection under the station display. Call the language/sound 
selection by using the green coloured key and select using .
... with the numeric buttons of the remote control
The set has a dynamic memory with 1680 station memory locations. If up to 9 
stations are stored, you only need to enter one digit; up to 99 stations, two dig-
its are needed; up to 999 stations, three digits are needed (refer to the station 
list to see how many stations have been stored).
1 digit stations
Press buttons 0 -9 for one second, and the station 
changes instantly.
Or press button 0 – 9 briefly, the station then changes 
after 2 seconds (the station changes immediately when 
only 9 stations are saved).
2- and 3-digit stations
After briefly pressing the first numeric button(s), keep the 
last numeric button pressed for one second, the station 
then changes immediately.
Or press all numeric buttons briefly, the station then 
changes after 2 seconds (the station changes immediately 
if up to 99 or 999 stations are saved).
4 digit stations
Press the four numeric buttons briefly, the station then 
changes immediately.
Call last viewed station (for DVB-T stations in GB)
You can switch back and forth quickly between two stations 
using this button.
... via the station list
Use OK to call the station list.
Select the station (if possible, the selected station will be 
displayed as a small picture)
or ...
... select with numeric buttons
call selected station.
Blue coloured key: sort alphabetically/according to bouquets/
numerically.
For an alphabetical display: Enter letters with the numeric button (like on a 
mobile phone keypad), select with  and call with OK.
For bouquet display (sorting according to broadcasting chains, only for DVB 
stations, not for DVB-T stations in GB): Enter bouquet number, select with 
 and call with OK.
Digital DVB-T stations are indicated by , DVB-C stations by  and DVB-S 
stations by . Encrypted stations are additionally indicated by .  
Ask your specialist dealer about decoders or the use of a CA module and a 
Smart Card for the reception of encrypted stations.
Daily operation
0 9 END OK 
  6  3SAT 
  7  S–RTL 
  8  N–TV 
  9  DSF 
10   TM3    
11 PRO7 
12 RTL 2 
13 WDR 3 
14 BR 
15 HR 
16 MDR 3 
17 N 3  COMP. IN 
 HDMI/DVI 
 VGA
 
 AV S  
 DVD 
 VCR 
    0  VIDEO 
    1  ARD 
    2  ZDF 
    3  SAT.1 
    4  RTL 
    5    VOX 
OK 
Station list                                Numerical 
Switch to ...                      Scan stations  21:00 - 21:45   Eifellandschaft 
...     Select station        Change stations 
Change sorting 
END OK 
OK 
a z 
 CNN INT. 
 CAM 
 
 DELUXE 
 DSF 
 
 EUROSPRT 
 
 HOT 
 HR 
  
 KIKA  COMP. IN 
 HDMI/DVI 
 VGA
 
 AVS 
 DVD 
 VCR 
 
 ARD 
  
 BR-ALPHA 
 BR3 
         
Station list                             Alphabetical 
Switch to ...                      Scan stations  21:00 - 21:45   Eifellandschaft 
...     Select letter        Change stations 
Change sorting 
41  ZDF  Eifellandschaft                   21:00 – 21:45Language/sound selection
all short
short  short  long
long
 
						

							15 -  
Basics about the menu operation
Menus are called via the MENU button or via the button for special menus and 
can be hidden by using these buttons or by using the END button. The menu is 
displayed in the bottom section of the screen. At the top, you can see additional 
information for the menu point selected. In the menus, navigate by using the 
cursor. You can make settings by using . When you exit the 
menu, the settings are adopted.
Example of the menu operation
We shall demonstrate how to navigate with the menus using the TV menu as an 
example. You can see which buttons you can use in the dark blue field on your 
TV set.
Open TV menu (in TV mode).
Select the function in the TV menu, e.g. “Sound“ (for sound 
settings). Use  to move the menu points displayed on the 
right into the dark blue field; use  to move the menu points 
displayed on the left. 
Select the sound function below with  or OK; you will then 
see a list of the sound settings.
In the sound settings, also select the function with , e.g. 
“Bass“ (for increasing or reducing the bass tones).
To set the bass tones, use  or OK to select the setting bar 
underneath.Set the bass tones by using .
If you want to make other sound settings, move up with  
to “Bass“ and select with , e.g. “more...“. You can also 
move up further to “Sound“ by using  and select other set-
tings in the TV menu (such as, picture settings).
Use OK to call additional sound settings. 
Select the sound setting using , e.g. “Auto volume“ and ...
... use  to select the auto volume option. 
Use  to select “on“ and activate the auto volume.
Press the END button to hide the menu.
Apart from the TV menu shown here, other menus can be opened in TV mode 
as follows: 
Call the Sound menu directly.
Quick calls for Image+ 
3, teletext subtitles, personal text 
pages, headphone volume, scan stations and to move the 
picture up and down.
Green coloured key: Call standard settings for picture and 
sound.
Using the volume control, you can also open other sound 
settings, such as Sound via, Sound adjustment, Sound effects 
and Loudness. 
The key  or OK must be pressed for the duration of the 
volume display for this.
Daily operation
Treble             ...
INFOENDTV menuSettings
Connections Recording
SoundPicture
INFO END  more ... 
Bass Treble TV menu 
Sound 4 
INFO END  more ... 
TV menu 
Sound 
Treble Bass 
 6 
INFO END BassTV menu 
6  Sound 
INFO END more ...
Treble   Bass TV menu 
Sound OK 
INFO END Auto voLoudspeaker soundHeadphone volume  TV menu 
Stereo              ...Sound 
Headphone sound  Bass 
INFO END Auto volume TV menu 
Sound  off on 
Picture adjustment        ...
INFOENDSettingsConnectionsRecordingSound TV menuPicture
Picture
Here you can adjust among other things: Contrast, colour, brightness, 
picture adjustment, sharpness, picture format. 
INFO END AV audio signal  Maximum volume sound 
Auto volume TV menu 
Sound 
Balance off              ... 
INFO END Auto volume TV menu 
Sound onoff 
 
						

							 - 16
Daily operation
For the info system ...
For each menu point, an info text is displayed at the top of the picture to help 
you with the setting. This saves you from having to refer back to the operating 
instructions. We shall demonstrate this using the station search option as an 
example:
Call the TV menu.
Select “Settings“.
In this example, you can see the options available after “Settings“. 
If you want to search for new stations, for example, use  to 
select “Stations“ in the line below. 
The info text indicates which settings you can make in “Stations“.Use  to select the line below, for example “Search wizard“.
The info text explains how you are to proceed.
Upon delivery, the TV set is configured so that the info texts are always dis-
played (Automatic info “yes“). In this case, you can hide the info texts by using 
the INFO button.
You can also configure the TV set so that you call the info texts when needed by 
using the INFO button (Automatic info “no“). You can find the setting to switch 
the automatic info option on or off via “TV menu under Settings – Miscellane-
ous – On-screen displays – Automatic info – yes/no“.
INFO END 
Stations                ...TV menu 
Settings 
Conne
ections Recording
Sound Picture  Settings 
Here, you can search for the stations automatically or manually as well  
as set the menu language, timer functions, parental lock, on-screen  
displays, etc. 
INFO END 
Search wizard                     ...Timer functions
Parental lock Stations
Language
Mi TV menu 
Settings  Stations 
The menu contains the automatic station search and the manual station  
setting. You can re-sort stations, enter and change station names and  
delete stations. 
INFO END 
Search wizard Manual adjustment Change stations Stations TV menu 
Settings  Search wizard 
Use this menu to search for stations automatically once certain settings  
have been made. 
If you want to search for stations with other than the displayed  
settings, select the "Change settings" menu. 
 
 
						

							17 -  
Daily operation
For the index ...
Using the index, you can access many operational functions directly. You can 
also find a great deal of information on technical terms about television. Before 
the alphabetical sorting, you can find the menu language option, the list of 
features integrated into the TV set and the repeat initial installation option. 
Call the index in the TV mode (without any other on-screen 
displays).
Info on the index item selected is visible at the top of the picture. If the OK 
symbol is displayed in the line selected, you can use the OK button to access 
the menu directly and carry out settings or selections.
This is how to select the index item:
Enter the first letter using the numeric buttons on the remote 
control (like on a mobile phone keypad); 
or
use  to go to the previous/next letter,
or
use P+/P– to scroll up or down through the pages
and use  to go from line to line.For example, you want to have the TV set switch off automatically: 
Select the index item “Switch off“ – “Automatic“.
Use the OK button to call “Switch off“ – “Automatic“.
The corresponding menu “Timer functions“ is displayed (in the TV menu – Set-
tings). You can now choose between “Switch off today only“ and “Switch off 
daily“ and enter the time.
a z 
END OK 
OK 
P+ 
P–   
Index  You can select your language for operating the TV set. Language 
Integrated features 
Repeat initial installation 
* 
Access code 
Active window (PIP) 
Automatic channel programming (ACP) 
AV (Audio/Video) 
  
Activate    Previous/next letter 
...     Select letter           Page / 
a z 
END OK 
OK 
P+ 
P–   
Index  You can set your TV set to switch off to stand-by mode once or every  
day at a given time. Switch off 
 Automatic 
 Manual 
Symbol rate* 
Teletext 
 Activate 
 Character set 
 FLOF 
Activate    Previous/next letter 
...     Select letter           Page / 
INFO END 
no                        ... One-time reminder
Switch off daily Switch off today only 
Wake  TV menu 
Settings 
Timer functions  Switch off today only 
If you want your TV set to switch off once automatically (to stand-by  
mode) select "yes" and enter the time. 
 
						

							 - 18
Setting the sound
Volume and other frequently used sound settings
Setting the volume
by using  or OK, you can call other sound settings ... 
and select using  ...
use  for the related selection/setting ...
... and use  to make the selection/setting there.
Sound adjustment allows you to adjust the sound characteristics to the station‘s 
sound. The Sound effects settings allow you to expand a Dolby Pro Logic Signal 
to a virtual surround signal by using “Dolby Virtual“; by using “Panorama“, you 
can enhance the foundation of the stereo sound virtually for the loudspeakers. 
Sound off/on
Sound off;
Sound on: Press button again or adjust volume.
Other sound settings:
Call the Sound menu
use  to select the sound function to be set and use for 
the related selection ...
and use  to select/set.
Sound settings: Treble and bass. Different menu items are displayed depend-
ing on the connected audio device (AURO, hi-fi amplifier). Under “more ...“ you 
will find the sound selection for loudspeakers and headphones, auto volume, 
headphone volume, AV audio signal, maximum volume and balance.
Picture settings
Call up TV menu.
Select „Image“ with  and selection with .
Use  to mark image functions to be set.
Use  for setting ...
... and use  to select/set.
Picture settings: Picture adjustment, Contrast, Colour, Brightness, Sharpness. 
Under “more ...“, you can find settings for Image+
3, Picture format, Move 
picture up/down, Auto format and Film quality improvement DMM3.
Direct control on TV set
On page 4, you can find illustrations of the control unit located on the set.
Switching station on the TV set
Station up: with + on the control ring
Station down: with – on the control ring
Switching the radio on/off or switching over to the radio 
Press R to switch the radio on or off.
Additional functions via the menu
In the radio or TV operating modes, you can make settings for Volume, 
Brightness, Contrast, Picture format and Stations. “Service” is intended for the 
customer service department.
use M to call the menu
use – or + to select the function to be set
use R for the related setting/selection
use – or + to set/select.
Use M to move one level up; you can use – or + to select other functions.
Daily operation
Volume             ... 24 
normal Loudness  Sound adjustment 
Sound effects 
VVolume 
Pop Classic  Sound adjustment 
Speech nonormal 
Sound off 
Sound on 
INFOENDmore ... SoundBass Treble4
INFOENDSound
Bass
6
Operating mode Contrast Picture foDirect control on TV set 
TVVolume Brightness 
Volume g mode Contrast Brightness Picture format Stat Direct control on TV set 24 
Volume Direct control on TV set 18 
Sound adjustment  Volume Sound effects Loudness  24 
Picture adjustment        ...
INFO END SettingsConnections RecordingSound TV menu Picture 
INFO END Colour
6 Picture
TV menu
 
						

							19 -  
Operating modes – TV
TV
In initial installation and daily operation, the TV set is in TV mode. This is also 
the case when none of the other modes of operation, such as EPG, Teletext, PIP 
or Radio, have been selected.
Each of these operating modes has a separate menu with separate functions for 
the coloured keys. Call the menu via the MENU button.
How the coloured keys work in TV mode
Note: The coloured keys do not work as described below with DVB-T stations in 
GB, but they operate as described on page 29 (Digital Teletext).
Red: the TV picture freezes. Pressing this button again starts 
the picture moving again. If your TV set is equipped with a 
digital recorder, the DR archive is called.
Green: Call personal settings/factory settings for picture and 
sound, save picture and sound settings as personal settings.
Yellow: call last station viewed. You can switch back and forth 
quickly between two stations using this button.
Blue: call programme info.
Show status display
Show/hide status
In the line above, you can see the name of the station and the sound mode. 
Displayed below are additional options (Time, Sound mode, Alarm time and 
Sleep timer) that can be selected in the “TV menu – Settings – Miscellaneous 
– On-screen displays“.
For the status display, the DVB station providers may offer additional selection 
options for each station. Thus, the corresponding colour key or the TEXT button 
is displayed:
Red: channel selection for multi-channel providers.
Green: language/sound selection.
Yellow: time selection.
Blue: protection of minors.
DVB subtitles.
If you press one of the coloured keys during the status display or you press the 
TEXT button, the related selection menu is displayed.
The status display subtitles refer only to the “DVB subtitles“ and are not 
provided by all stations. The options you see depend on the particular station 
(many stations broadcast subtitles via teletext).
The status display is displayed automatically when a new programme begins 
with options different to the previous one.
Notes: 
•  In the sound mode, Mono! means that you have switched manually from 
stereo to mono, for example.
•  The selection menus are only available as long as the status display is 
displayed. You can call them again at any time by pressing the END button 
on your remote control.
Calling the index
Calling the index
You can find more information on the index on page 17.
Call up factory settings Store as per Standard settings pict./soundOKActivate
ENDINFO
Call up personal settingsOK
ENDDetailed info (teletext)Programme info        14:43
Detailed info
Programme preview (t
   1  ARD      Eifelland  14:30 - 15:15
OK
14:42          Alarm time  20:00          Sleep timer  23:00Language/sound selection
1  ARD       Eifellandschaft  14:30 - 15:15  Stereo
a z 
END OK 
OK 
P+ 
P–   
Index  You can select your language for operating the TV set. Language 
Integrated features 
Repeat initial installation 
* 
Access code 
Active window (PIP) 
Automatic channel programming (ACP) 
AV (Audio/Video) 
  
Activate    Previous/next letter 
...     Select letter           Page / 
 
						

							 - 20
Operating modes – TV
Call additional functions
Select additional functions such as Image+ 3, Teletext subti-
tles, Personal teletext pages, Headphone volume,
Scan stations and to move the picture up and down.
Call timer overview
If timer recordings have been programmed, you will see when 
which station is recorded here.
Select picture format
The TV set sets the best picture format automatically when 
Auto format is switched on. If you want to set a different 
format, press this button until the desired format is selected or 
select the format with .
You can switch the panorama picture over to distortion-free representation on 
your TV set. Dark margins are then visible on the left and right of the picture. 
Switching over: Keep the M button on the set pressed, at the same time press 
the ”Picture format” 
  button on the remote control briefly. 
Resetting: Press the same button combination again.
Move picture up/down
To make picture subtitles visible, you can useto move 
the picture up or down with the picture formats “Panorama“, 
“Cinema“ and “Zoom“.
Note: for DVB-T stations in GB you can switch back and forth quickly between 
two stations using this button.
TV menu
Call up the TV menu
You will find a description of the picture and sound settings on page 18. The TV 
menu offers other options for recording, connections and settings of the TV set.
For a recorder that is logged in, you can find the following 
menus in the “Recording“:
Recording wizard - to programme new timer recordings
• Via EPG     • Via teletext     • Manual
You will find further information about timer recording on page 32. 
Timer list
Here you will find a list of programmes programmed for recording. You can 
change the recording data or delete programmed recordings and programme 
new recordings.
Pre-record time and Post record time
For recordings without VPS/PDC, set a lead and lag time here so that the pro-
gramme is fully recorded despite any slight differences in the time. 
Under “Connections“ you will find the following functions:
New devices/modifications (connection wizard)
The connection wizard helps you connect and log in additional equipment such 
as video recorders, DVD players/recorders, camcorders/digital cameras, pay TV 
decoders, equipment with component signals and digital HDMI/DVI signals.
Antenna DVB
• Antenna DVB-T     • Antenna DVB-S 
(1
You can find more information on pages 12 and 13.
Digital Link Plus
Transmission of the station data from the TV set to the video/DVD recorder if a 
recorder with Digital Link Plus is connected.
Miscellaneous (connections)
•  Set AV norm for the connections manually (if it is not recognised automati-
cally).
•  “Assign audio digital signals“ to one of the AV sockets.
•  “Allow switching voltage“ to display the signals of the connected device 
immediately on the screen via Euro AV during playback.
•   RGB insertions at AV2 to play back RGB signals at all station storage locations.
•  Select decoder stations and set sound encoding.
(1 only for sets with DVB-S
Image+ Teletext subtitlesPersonal teletext pages Additional functions off                       ...
INFO END 
Zoom
Cinema  Panorama
16:9Picture format
4:3
END
Timer list           Fri 12.09./14:1212.09.  18:00-18:30  3SAT    Die Köchin, die Putzfrau und d
Detail     New recording      Change
DeleteTEXTINFO
Picture adjustment        ...
INFO END SettingsConnections RecordingSound TV menu Picture