Loewe Art 47 Sl Operating Instructions

							61 -
Calling the PhotoViewer menu 
In the PhotoViewer menu you can make picture settings and select the 
memory medium.
➠ The photo overview is displayed.
Call PhotoViewer menu.
 
Explanations of the setting possibilities:
Within the folder select a photo directly or go to the 
beginning or end of the folder.
With Optimum size the photo is reduced or enlarged in 
size so that the screen is optimally filled.
With Original resolution each pixel of the photo represents 
one pixel on the screen. If the photo resolution is higher 
than that of the screen, then portions of the photo will 
be cropped.
Set the display time per photo in a slide show to between 
3 and 60 seconds.
The loading time of the photo depends on the photo size, 
the number of saved files and the transmission speed of 
the memory medium. Therefore a photo change may 
take longer than specified.
There is a choice of four different photo transitions for 
changing slides. You can also have the photo transitions 
run in sequence.
Display additional information about the picture: Recording 
time and date, resolution and picture size.
The settings correspond to the picture settings in TV mode 
(see page 24).
Select whether or not the previously heard sound is to 
be heard during the PhotoViewer operation.
Select memory medium from which the photos are to be 
reproduced. This menu item is only displayed if at least 
two memory media are available. Open folder
➠  Folders will only be displayed if they were created on the 
memory card / USB stick.
Mark a folder in the photo overview.
 OK Open folder.
The photos in this folder are displayed.
Marking photos for slide show
Mark the photos that you want to display in a slide show.
Navigate to a photo.
Blue button: Mark photo for slide show.
Start slide show
➠  No pictures are marked: All photos of the folder that 
was just opened will be displayed.
➠ Photos marked: Only marked photos will be displayed.
PLAY button: Start / continue slide show.
 OK  calls the photo overview.
PAUSE button: Pause / continue the slide show.
Yellow button: Zoom picture (only in pause mode).
 Rotate picture to left/right in 90º steps (only in 
Pause mode).
 or P+ Next photo.
 or P– Previous photo.
STOP button: End slide show.
Operating additional equipment
Go to...
Picture display
Picture change
Picture 
crossovers
Photo info
Picture settings
Sound
Select memory 
medium
OK
ENDINFOMENUOKP+
P–
USB 1:\Folder _1\                     29 pictures
Open folderSlide show
	~
						

							- 62
Operating additional equipment
MusicBox
You can play music files in MP3 or WMA format which are saved on a 
USB stick or a memory card in a card reader. You can also collect the 
music titles in play lists.
Connection
➠  Certain USB memory media may not be supported by this device.
➠  Your memory medium should not exceed a total capacity of 8 GB. Larger 
memory media may not be supported. The read-in time of the memory 
medium depends on the stored data volume.
➠  The file names must have the extension ".mp3" or ".wma". Alternative 
specifications such as MP3 Surround or similar are not supported.
Plug a card reader (with a USB cable) or a USB stick into the USB port on 
the TV set (see pages 5 to 7).
Starting the MusicBox
Call Assist+
 menu.
 Mark MusicBox,
 OK continue.
If there is only one memory medium the MusicBox is 
started with the MusicBox list (see right column).
If several media are available select memory medium with
and then with
 OK start MusicBox.
Ending the MusicBox 
Remove used memory medium.
Or:
Press END button (while status window is displayed)
Or:
Press TV button.
Or:
Press the ASSIST button and call another function in the 
Assist+
 menu.
➠  If the MusicBox is ended during playback, the MusicBox 
remembers the appropriate place in the title. If the TV 
set is not switched off or the memory medium removed 
in the meantime, the playback continues at this point 
the next time the MusicBox is called. The MusicBox then 
starts immediately on the MusicBox status window (see 
right column).Select/play music
After starting the MusicBox, the content of the memory medium, the 
MusicBox list, is displayed.
Mark folder, scroll with P+/P- if necessary,
 OK  open selected folder.
   You see the music files (titles) and/or sub-folders in 
the opened folder.
One folder level back:
Select 
... and press OK.
 Mark title, scroll with P+/P- if necessary,
 OK  play marked title.
   Then the MusicBox status window opens with informa-
tion about the played title. 
➠  If the file contains additional information (ID3 tags), the 
title, singer, album title etc. are displayed.
ENDINFOMENU
OK
OK
MusicBox                                Files
Backup
MP3
Photo
Video
USB 1:\
Open folder
Play lists
Browse/sort
ENDINFOMENU
OKP+
P  -
OK
MusicBox                               Files
     ..
Title_01.mp3
Title_02.mp3
Title_03.mp3
Title_04.mp3
Title_05.mp3
Title_06.mp3
Title_07.mp3
Title_08.mp3
Title_09.mp3
Title_10.mp3
Title_11.mp3
USB 1:\MP3
play back
Page Play lists
Browse/sort
ENDMENUOKINFO
Volume 30 „Chasing Cars“                 	~
						

							63 -
Operating additional equipment
Functions of the control buttons
➠ Title is played.
➠ Fast forward and rewind is no possible with WMA files.
STOP button: Once: resume stop, twice: stop.
PLAY button: 
After resume stop: Continue playing at place where 
playback was interrupted.
After stop: Start playing the first title according to the set 
sorting.
For playback: Start the current title from the beginning.
For pause: Continue playback.
PAUSE button: Pause / continue playback.
Short: next title, long: wind.
Short: previous title, long: rewind.
Settings in the MusicBox status window
Red button: Switch off TV screen. 
Press red button, INFO or OK to switch back on.
Reduce info window to one line / maximise again.
 OK Show MusicBox list.
MusicBox – Browse/sort
You can browse or sort the contents of your memory medium with the 
coloured buttons according to certain criteria (file names, titles, artists, 
albums). 
➠ The MusicBox list is displayed.
Blue button: Call Browse/sort.
The MusicBox overview is sorted according to Files at the 
beginning. The sorting is based on the file names of the 
music files regardless of their ID3 tags. 
 Select file/folder and play/open with OK.Sort according to artists
Green button: Show Artists.
All music titles are sorted alphabetically according to 
artists (ID3 tags).
 Mark artist, scroll with P+/P- if necessary or enter 
the initial letter with numeric buttons like a mobile 
phone keypad (see page 16).
 OK Call Albums by ....
The albums of the selected artist are displayed sorted 
alphabetically. 
Mark album and select with OK.
Select title in album and play with
 OK in MusicBox status window.
TEXT: Call Titles by ....
The titles of the selected artist are displayed sorted alpha-
betically.
Select title and play with
 OK in MusicBox status window.
Sorting according to titles
Yellow button: Show All Titles.
All available titles are sorted alphabetically by ID3 tags and 
displayed with the appropriate artist.
Select title and play with
 OK in MusicBox status window.
Sorting according to albums
Blue button: Show All Albums.
All available albums are sorted alphabetically by ID3 tags 
and displayed with the appropriate artist.
Mark album and select with OK.
 Select title in album and play with
 OK in MusicBox status window.
Sorting according to files
Red button: Show file overview.
Exit sorting
Exit search/sorting. The new sorting is retained in the 
MusicBox list.
OK
a
z-OKTEXT
Savatage
Sido
Sinatra Frank
Starship
Steel Pulse
System Of A Down
Texas Lightning
Thin Lizzy
MENU
END
INFO
All Titles
All Albums Files
Select letter Albums by ...
Titles by ...     
Page P+
P -
INFO„Chasing Cars“                  	~
						

							- 64
Operating additional equipment
MusicBox – Play lists
You can save and call your music titles in play lists. Change and create 
play lists as you like.
The play lists are created on the memory medium in the common M3U 
format for simple exchange with the PC.
Call / play play list
➠ The MusicBox list is displayed.
Red button: Call Play lists.
In the play list overview you see the created play lists on 
the left hand side of the dialogue. On the right next to it 
you see the music files in the marked play list.
  
Select play list, scroll with P+/P- if necessary.
 OK  The play list is played in the MusicBox status 
window starting with the first title. The name of 
the play list is displayed after the title.
 OK  The play list is displayed again.
  Change from list selection to title selection. 
  Select title, scroll with P+/P- if necessary,
 OK  the play list is played in the MusicBox status 
window from the marked title.Create new play list / add title
➠ The play list overview is displayed.
➠  List selection (left column) must be selected.
If not, change the column with .
Blue button: Call Create play list.
A new empty play list is created. The file selection is 
visible on the left.
Mark title/folder, scroll with P+/P- if necessary,
 OK  Adopt marked title to play list or open marked 
folder.
Yellow button: Adopt marked folder to play list. 
Change play lists
You can adapt the play lists as required. It is possible to move the titles in 
the play lists or remove them from the list. The play list can be renamed 
or deleted completely. 
➠ The play list overview is displayed.
Green button: Call Change play list.
Go to the page of the play list (right column).
Green button: Select play list to be changed.
ENDOK
INFO
OK
Build/change play lists
Next play list
Browse/sort Abba
ACDC
Elton John
Eros Ramazzotti
Rolling Stones
Title_1.mp3
Title_2.mp3
Title_3.mp3
Title_4.mp3
Title_5.mp3
Title_6.mp3
Title_7.mp3
Open folder
Adopt to play list
Page 
P+
P  -
FilesPlaylist14
OKINFOEND
OK
Play lists
Change play list
Delete play list
Create play list Alternative          1 Bolero         Maurice Ravel
Instrumental         2 All Night Long      Lionel Richie
Jazz &  Funk         3 Burn          Deep Purple
Metal            4 All The Small Things   Blink 182
Oldies             5 Summer In The City   Joe Cocker
R’n’B / HipHop        6 In The Mood      Glenn Miller
Reggae / Ska         7 Rocket Man       Elton John
Rock            8 Fight For Your Right   Beastie Boys
Playlist 1           9 Paint It Black      Rolling Stones
Playlist 10        10 Me And Bobby Mc...   Janis Joplin
Playlist 11        11  Can’t Buy Me Love       The Beatles
Playlist 12        12 No Woman No Cry    Bob Marley
Playlist 13        13 Bad Moon Rising     CCR
Page 
P+
P -Start play list
MusicBox list
OK
OKINFOENDP+
P -09-
Play lists
Alternative          1 Bolero         Maurice Ravel
Instrumental         2 All Night Long      Lionel Richie
Jazz & Funk          3 Burn          Deep Purple
Metal            4 All The Small Things   Blink 182
Oldies            5 Summer In The City   Joe Cocker
R’n’B / HipHop        6 In The Mood      Glenn Miller
Reggae / Ska         7 Rocket Man       Elton John
Rock            8 Fight For Your Right   Beastie Boys
Playlist 1             9 Paint It Black      Rolling Stones
Playlist 10        10 Me And Bobby Mc...   Janis Joplin
Playlist 11        11  Can’t Buy Me Love       The Beatles
Playlist 12        12 No Woman No Cry    Bob Marley
Playlist 13        13 Bad Moon Rising     CCR
Change play list
Delete play list
Create play list Page Start play list
Select title
MusicBox list
ENDOK
INFO
OK
Build/change play lists
Next play list
Move title
Rename play list Abba
ACDC
Elton John
Eros Ramazzotti
Rolling Stones
Title_1.mp3
Title_2.mp3
Title_3.mp3
Title_4.mp3
Title_5.mp3
Title_6.mp3
Title_7.mp3
Remove from play list
Page 
Clear play list
P+
P  -
FilesPlayliste10
1   Lay it Down
2   Fallin’
3   Do that to Me One More...
4   Hero
5   Insatiable
6   There You’ll Be
7   Let’s Wait a While
8   What If
9   Stillness of Heart
10 Free-One
11 Stop Crying Your Heart
12 Separate Lives
 
						

							65 -
Operating additional equipment
Rename play lists
➠  Play list (right column) must be selected. If not, change 
column with.
Blue button: Starts Rename play list.
Numeric buttons: Enter new name (same procedure as 
for rename station, see page 30).
 OK  Save new name.
Move titles in the play lists / change order
➠   
Play list (right column) must be selected. 
Mark title to be moved.
Yellow button: Starts Move title.
 Select insertion position at which the marked title 
is to be inserted. 
 OK Move title.
Remove titles from play lists / clear play list
➠   
Play list (right column) must be selected. 
Mark title to be deleted.
 OK  Remove marked title from play list.
Or:
Red button: Starts Clear play list.
 OK  Confirm clearing play list. 
Delete play list from memory medium
➠  The play list overview is displayed. 
Mark play list to be deleted.
Yellow button: Starts Delete play list.
 OK  Confirm delete play list. 
Exit play list overview
➠ The play list overview is displayed.
Red button: Call MusicBox list.
Or:
END: Call MusicBox status window.MusicBox – Menu
In the MusicBox menu you make sound settings, can select the memory 
medium and set the repeat mode.
➠ MusicBox must be activated.
Call MusicBox menu.
Explanations of the setting options:
Select memory medium from which the audio files are to 
be used. This menu item is only displayed if at least two 
memory media are available.
The settings correspond to the picture settings in TV mode 
(see page 24).
The settings correspond to the sound settings in TV mode 
(see page 22).
Titles can be repeated in two ways:
Title 
						

							- 66
Operating Loewe equipment
Using the remote control for the TV mode of the TV set
Press the TV button, the display above it will light for 
approx. 5 seconds.
Using the remote control for additional equipment
Press the REC, DVD or AUDIO button, the display above 
it will light for approx. 5 seconds.
As long as a button is pressed, the display of the selected operating mode 
lights up (TV – REC – DVD – AUDIO). This allows you to check which 
operating mode the remote control is set to every time you press a button.
Setting the remote control for other Loewe devices
Press required device button along with the STOP button at the same time, 
until the associated LED display flashes twice. Then enter the two-digit 
device code from the list.
Device Code Factory setting
Loewe ViewVision 8106 H 10
Loewe Viewvision, Centros 21x2 12
Loewe ViewVision DR+
 DVB-T 13 REC
Loewe Auro 2216 PS/8116 DT 14
Loewe BlutechVision 15
Loewe Soundprojector 17
Loewe TV - digital radio 19 AUDIO
Loewe Mediacenter 20
Loewe BlutechVision Interactive 21 DVD
HDMI CEC mode 22
Loewe Soundprojector 2 23
Loewe AudioVision 24
Resetting to factory setting 99
The associated LED display flashes twice.
➠  The codes shown here only apply for direct operation of the accessory 
device. For operation of the accessory device via the TV set, e.g. with 
concealed installation, see page 51.
Operating additional equipment
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
18
19
20
21
22
23
24
25
26
27
28
29
30
31
33
17
 
						

							67 -
Functions for the Loewe DVD recorder (Centros 1202, 2102 HD, ViewVision DR+
)
TV Sound off/on
LED indicator for current operating mode
Switch over to operate TV set
Switch over to operate Recorder
Timer recording menu; timer recording list menu
STOP: Title List; PLAY: Edit thumbnail;
CARD: Photo-, Music-, Film-Mode
ViewVision DR+
: Timeshift Mode
STOP: Call AV selection (AV1-AV4,DV,TV)
ViewVision DR+
: PLAY: skip 15 Sec.
User interface of loaded DVD
MENU: original / playlist
Show/hide menu
V–/V+ TV Volume down/up
Status display (TV, DVD)
MENU: confirm the menu selection
Green button: ShowView menu
Red button: new chapter marker
PLAY: press short: Start of current chapter/previous chapter;
press long: search back; PAUSE: press short: slow motion back
Record
Pause /single frame
Switch on/off - on stand by
TV Radio Digital
Switch over to operate DVD-Player
TV Sound menu
STOP: Select station directly
MENU: enter numbers or letters
MENU: enter numbers or letters
ViewVision DR+
: STOPP: Call AV selection
Card Reader operation
ViewVision DR+
: „Home“ menu
PIP (picture in picture)
Info; PLAY: menu bar
MENU: hide menu
P+/P– PLAY: Next chapter; STOP: Select station up/down
MENU: select/set
Yellow button: Zoom
Blue button: DISC: short: Set marker; long: Marker search
Playback
PLAY: Press short: next chapter; Press long: search forward
PAUSE: Press short: slow motion forward
Stop Functions for the Loewe DVD player (Auro 2216 PS, 8116 DT)
Sound off/on
LED indicator for current operating mode
Switch over to operate TV set
Switch over to operate Recorder
Sleep timer
Set TV picture format; RADIO: Mono/Stereo
DISC: Repeat; RADIO: display RDS name/frequency of station
DISC: User interface of loaded DVD
Show/hide menu; MENU: close window
V–/V+ Volume down/up
DISC: Title/Chapter overview; RADIO: station table
MENU: confirm menu selection
Green button: Title/Chapter selection
Red button: DISC: camera position
DISC: short: beginning of chapter/title previous chapter;
long: search back;
RADIO: short: fine tuning back long: search back
no function
Pause; single frame; slow motion
Switch on/off - on stand by
short: TV Radio Digital; long: Auro FM/AM-Radio
Switch over to operate Auro
Select sound format
DISC: select chapter/title; RADIO: select stored station;
MENU: enter digits
MENU: enter numbers or letters
DISC: Repeat A-B; RADIO: FM/AM-mode
Select external audio source
DISC: menu bar
MENU: context help
DISC: Status display; RADIO: station table
MENU: hide menu
P+/P– DISC: next/previous chapter; RADIO: station forward/back
 DISC: chapter up/down; MENU: select up/down;
 DISC: search back/forward; MENU: select left/right
Yellow button: Zoom
Blue button: Set marker
Playback
DISC: short: next chapter/title; long: search forward
RADIO: short: fine tuning forward; long: search forward
Stop
Operating additional equipment
1
2 
3 
4 
5 
6 
7 
8 
9 
 10 
 11 
 12 
 13 
 14 
 15 
 16 
 17 
 18 
 19 
 20 
 21 
 22 
 23 
 24 
 25 
 26 
 27 
 28 
 29 
 30 
 31 
 32 
 33
1
2 
3 
4 
5 
6 
7 
8 
9 
 10 
 11 
 12 
 13 
 14 
 15 
 16 
 17 
 18 
 19 
 20 
 21 
 22 
 23 
 24 
 25 
 26 
 27 
 28 
 29 
 30 
 31 
 32 
 33
 
						

							- 68
Operating additional equipment
Rotating the TV set (upgradable interface)
Your TV set can be upgraded with the connection for a rotating foot 
control. If the set is assembled with a Loewe stand with motor drive, 
you can align it to suit your sitting position using the remote control.
➠ A motor unit is connected.
➠ In normal TV mode, without other displays.
 Rotate the TV set.
Do not place any objects in the rotation range of the TV set that could 
obstruct the rotation or that could be knocked over by the rotation 
movement.
Setting the range of rotation
You can determine the range of rotation (maximum +/- 40°) of the TV set 
by setting the maximum right and left stop.
Call TV menu.
  Select Settings,
 go to the menu line below.
 Select Miscellaneous,
 go to the menu line below.
 Select Rotate TV,
 go to the menu line below.
 Select Basic adjustment,
 OK  calls the basic adjustment.
Basic adjustment (right)
Turn your TV set as far to the right as the installation 
position allows. This will be the maximum right 
rotation position in future.
 OK  confirms basic adjustment to right.
Basic adjustment (left)
Rotate your TV set as fasr to the left as the installation 
position allows. This will be the maximum left rotation 
position in future.
 OK  ends the basic adjustment.
Close the menu.Specifying the switch off position
This is where you specify the position that the TV will take when it is 
switched off. In order for the TV set to return to the determined switch-
off position when switching it off, this must be activated (see below).
Call TV menu.
  Select Settings,
 go to the menu line below.
 Select Miscellaneous,
 go to the menu line below.
 Select Rotate TV,
 go to the menu line below.
 Select Set switch-off position,
 OK calls Set switch-off position.
Set the desired switch-off position.
The TV set rotates in the process.
 OK  Save the set position as the switch-off position.
Close the menu.
Activating the switch-off position
Call TV menu.
  Select Settings,
 go to the menu line below.
 Select Miscellaneous,
 go to the menu line below.
 Select Rotate TV,
 go to the menu line below.
 Select Activate switch-off position,
 go to the menu line below.
 Select yes.
Close the menu.
If the TV set is switched off with the on/off key on the remote control or with 
the switch integrated in the display then it will turn to the defined siwtch-
off position. When it is switched back on, it returns to the position last set.
END
OK21 Basic adjustment (right) Rotate TV
Proceed
END
OK-30 Basic adjustment (left) Rotate TV
End of basic adjustment
ENDINFO
OK0 Set switch-off position TV menu
Settings
Miscellaneous
Rotate TV
Adopt
 
						

							69 -
Troubleshooting
Problem Possible cause Remedy
All menus are displayed in the wrong language. The menu language was set incorrectly.Set the menu language:
Press the INFO button in TV mode (Index). 
Mark the first key word and call it with OK. 
Then select the language and confirm it with 
OK.
In the TV menu, Connections cannot be called 
(displayed in grey).A timer recording is in progress. Wait until the timer recording ends or delete 
the timer recording (page 58).
The control functions of the Loewe Recorder 
and the Timer are not working or are not 
working properlya) The Digital Link function is not activated or 
not possible in the recorder.
b) EURO-AV cable is not connected.
c) Recorder is not logged in.a) Activate Digital Link in the recorder (see 
operating instructions of the recorder).
b) Connect EURO-AV cable (page 49).
c) Register recorder (page 46).
General problems when connecting external 
devices via an AV input.a)  The device is not logged in to the connection 
wizard or is connected differently than is shown 
in the connection diagram.
b) The AV standard is set incorrectly.
c) The signal type is set incorrectly.a)  In the connection wizard (TV menu  
Connections  New devices/modifications) 
compare the connection diagram with the 
actual installation and connect as illustrated 
(page 46).
b) Set the correct standard (page 18).
c) Set the correct signal type (page 47).
 If for AV standard or AV signal is set to 
"Automatic" then this can cause errors to 
be detected with signals that do not 
comply with standards. In this case 
standard and signal must be set according 
to the information in the operating manual 
of the external device.
The connection of a decoder does not 
function or does not function properly.a) The signal is not decoded because the correct 
decoder stations have not been selected in 
the connection wizard.
b) In decoder mode the sound is missing 
because the wrong decoder sound has been 
assigned in the connection wizard.a) Follow the instructions in the connection 
wizard (
TV menu  Connections  New 
devices/modifications) and select the 
appropriate decoder transmitter (page 46).
b) Follow the instructions in the connection 
wizard and select the right audio source 
(Decoder, TV oder Autom.) (page 46), see 
also decoder instructions.
Errors occurred when running a CA module. Switch the TV set off. Remove the CA-module 
from the TV set. Wait a few seconds. Reinsert 
the CA-module. Switch the TV set on again.
 
						

							- 70
Troubleshooting
Problem Possible cause Remedy
Digital Link Plus does not work. a) EURO-AV cable is not fully wired (pin 10 not 
wired).
b) Some recorders can only adopt stations 
during the initial installation of the TV set.a) Replace the EURO-AV cable. 
b) Restore the recorder to the as-delivered 
state (see recorder's operating manual).
With Teletext various character sets are 
displayed incorrectly.The wrong character set has been set in the 
Teletext menu.Set the right character set: Select Teletext 
menu  Settings  Character set  Standard 
or the appropriate character set.
No sound via the external digital audio 
amplifier.a) The external digital audio amplifier does not 
support the selected sound format (Dolby 
Digital, dts, MPEG).
b) TV set and external digital audio amplifier are 
not connected with each other.a) Set PCM stereo on the DVD player in the 
sound selection. For DVB stations on the 
TV set switch to stereo in the Status display 
(END) – Language/sound (green button).
b) Connect AUDIO DIGITAL OUT from the TV 
set to a digital input of the external digital 
audio amplifier and select the appropriate 
input to this.
The picture of a connected external recorder 
is visible but the timer cannot be called.The device is not registered in the connection 
wizard or is connected differently to shown in 
the connection diagram.In the connection wizard (TV menu  Connections 
 New devices/modifications) compare the 
connection diagram with the actual installation 
and connect as illustrated (page 46).
The picture of a connected external recorder 
is visible but the error message no recorder 
available is still output.The device is not registered in the connection 
wizard or is connected differently to shown in 
the connection diagram.In the connection wizard (TV menu 
 Connections 
 New devices/modifications) compare the 
connection diagram with the actual installation 
and connect as illustrated (page 46).
Photo on the USB stick is not displayed 
correctly in the PhotoViewer or a 
"?“ appears.The photo is not available in a displayable 
format.Convert photo file into a standard JPG format 
on the PC.
A programmed recording was not made.Recording of analogue stations with VPS data:
The programme to be recorded was not (no longer) 
in the programmes offered by the station via 
VPS.
Recording of DVB stations with automatic time 
control:
The provider deleted the programme from the 
EPG data, for example due to a programme 
change.The stations are exclusively responsible for the 
transmission of VPS data (for analogue stations) 
or for the use of the automatic time control (for 
DVB and MHEG-5 stations). The availability of 
the appropriate data cannot be guaranteed.