Linksys Router BEFW11P1 User Manual

You can access this screen at any time by clicking the Advanced button and
then clicking the DMZbutton.
The DMZ feature, when enabled, drops f irewall protection from a device on
your Network, allow in one computer on your Network to be exposed to the
Internet. This enables unrestricted 2-way communication between the “DMZ”
and other Internet users or servers. Without this feature, such access would be
blocked by the Firewall. Any Internet user who knows the DMZ computer’s IP
Address can connect to the...

You can access this screen at any time by clicking the Advanced button and
then clicking the Routingbutton.
If you have a router already attached to your network and are connecting the
Wireless AP + Cable/DSL Router, you will need to utilize the Routing feature
to prevent conflicts.
Any existing entries are listed. To view and edit the details of an existing entry,
select it from the “Routing Table” drop-down menu and click the Get Databut-
ton. After making any changes in the “Properties” f ields, click...

Etherfast
®Wireless AP + Cable/DSL Router with PrintServer
You can access this screen at any time by entering the following IP Address into
your web browser:http://192.168.1.1/MAC_addr.htm
You should see the following screen displayed within your browser:
The MAC address specif ically identif ies the Wireless AP + Cable/DSL Router
on the WAN port. Some ISPs may require you to register this address with
them. When necessary, you can set the MAC Address from this screen and click
the Savebutton to set the...

1. When you see the Welcome screen, click the Nextbutton to continue. This
will bring up the Select Components screen. “User Manual” and “Print Port
Driver” will be selected by default. If either of these is deselected, the
PrintServer drivers will not be installed completely. Click the Nextbutton
to continue.
2. The next screen will ask you to choose a destination location. A default
installation path will appear but you may click the Browsebutton to choose
a different location. Then, click the...

Adding a printer under Windows 95, 98, or Millennium is done in two parts.
First, you’ll identify the printer for the PrintServer and then the printer will be
conf igured. In the example given below, our printer may vary from yours and
it is assumed that no printer has yet been added. Screens, therefore, will vary
depending on the printer you add and if a printer was previously added.
1. After you f inish installing your PrintServer drivers, the following screen
will appear, asking for you to verify that...

For the next part, you will need to con-
f igure your printer to function through
the Wireless AP + Cable/DSL Router’s
Printer port.
1. Go to “Add Printer” by clicking the
Startbutton, selecting Settings, and
clicking Printers.
Then, to begin the conf iguration
process, click the Nextbutton.
2. The next screen will ask how your printer is attached to your computer.
Since your printer is being connected to a network, rather than a single
computer, you will still want to select Local Printer. Do not...

5. The “Print Port Conf iguration” screen will now assign the printer drivers
that you installed to
the printer connect-
ed to the Wireless
AP + Cable/DSL
Router. Click the
Browse Device
button to select the
driver.
6. The driver for the device that you
selected in step 4will automatically
appear with the device number and IP
Address, as shown in this screen as
“SC00007D 192.168.0.1”. (Your port
number may be different.) Make sure
the device is selected and click the
OKbutton to continue.
7. The “Print...

9. Your printer has now been added. To verify that it is functioning properly
through the Wireless AP + Cable/DSL Router, you will want to print a test
page. Click the button beside “Yes (recommended)” to print the test page
and then click the Finishbutton to complete adding your printer.
If you opt to print a test page, a window will appear asking if the test page
printed correctly. If it did, click the Ye sbutton to close the window. If it did not
print correctly, click the Nobutton and you will be...

3. The next screen shows all of the Wireless AP + Cable/DSL Router’s avail-
able ports. The port you will want to conf igure is the printer port, shown in
this screen as “LPT1:SC00007D Shared Port”. (Your port number may be
different.) Make sure this port is selected and click the Configure Portbut-
ton to continue.
4. The “Print Port Conf iguration” screen will now assign the printer drivers
that you installed to the printer connected to the Wireless AP + Cable/DSL
Router. Click the OKbutton to...

Once the correct printer has been selected or the driver’s location has been
specif ied on your driver disk, click the Nextbutton.
7. At this stage, Windows NT will notify you that a driver has already been
installed for this printer. This is due to an idiosyncrasy in Windows NT.
Though you have not already installed printer drivers, you will want to
select Keep Existing Driver (recommended). DO NOTchoose Replace
existing driver. Click the Nextbutton to continue.
54
5. Now that the port has been conf...