LG Wm2487h M Service Manual

31
Disassemble the top plate assembly.
Pull out the drawer.
Push out the DISPENSER ASSEMBLY afterunscrew 2 screws.
Unscrew the nut at the lower part of the dispenser.
Disassemble the 4 connectors from the valves.
Unscrew 2 screws from the back of the cabinet.
Disassemble two (or three) connectors from 
the NOISE FILTER.
Unscrew a screw from the TOP BRACKET.
Wire Color
Blue Housing (YL-BK)
Red Housing(VT-BK)
White Housing(WH-BK)
Blue Housing(GY-BK)
Red Housing(BL-BK)
5
DISPENSERASSEMBLY
NOISEFILTER 

32
Unscrew the 5 screws from upper of the canbinetcover.
Unscrew the screw from filter cover.
Put a flat ( -) screwdriver or putty knife into the both
sides of the filter cover, and pull it out.
Unscrew the screw from the lower side of the cabinet cover.
CABINETCOVER 

33
Open the door.
Disassemble the clamp assembly.
Tilt the cabinet cover.
Disconnect the door switch connector.
NOTE: When assembling the CABINETCOVER, connect the connector.
Lift and separate the cabinet cover.
Disassemble the clamp assembly.
Disassemble the Gasket. 

34
Open the door.
Unscrew the 7 screws from the HINGE COVER.
Put a flat ( - ) screwdriver into the openng of the hinge,and pull out the hinge cover.
Unscrew a screw from the lower side of door.
Disassemble the door upward.
DOOR
Open the door and disassemble the CLAMPASSEMBLY.
Unscrew the 2 screws.
DOORLOCKSWITCHASSEMBLY
Be careful! The door is heavy.
NOTE 
• Reconnect the connector after replacing the
DOOR SWITCH ASSEMBLY. 

35
Disassemble the cabinet cover.
Separate the pump hose, the bellows 
and the circulation hose assembly from the
pump assembly.
Disassemble the pump assembly in arrowdirection.
Disassemble the cabinet cover.
Separate 2 connectors from the heater.
Loosen the nut and pull out the heater.
Disassemble the cabinet cover.
Unplug the white connector from the thermistor.
Pull it out by holding the bracket of thethermistor.
CAUTION  • When assembling the heater, insert the    heater into the heater clip on the...

36
Disassemble the cabinet cover.
Separate the heater from the tub.
Remove any foreign objects (wire, coin, etc.) byinserting a long bar in the opening.
TOP PLATE ASSEMBLYUnscrew 2 screws on the back of the top plate.
Pull the top plate backward and upward as shown.
Disconnect the connector. 
Disassemble the lamp assembly. 

37
Disassemble the back cover.
Remove the bolt.
Pull out the Rotor.
Unscrew the 2 screws from the tub bracket.
Remove the 6 bolts on the stator.
Unplug the 2 connectors from the stator.
Disassemble the damper hinges from the tuband base.
Separate the dampers.
NOTE  • Once removed, replace the damper with new one. 

38
To check out the fault diagnosis of TSG, in caseof removing the water inside, you can pull out
the plug and let the water drain away. 
Be cautious in case of the TSG is hot
temperature.
Remove the housing coupled the TSG 
(Heater, Water level frequency-sensor,
Thermistor)
Taking out the screw of the TSG and Body
Frame. 

39
Taking out the screws of Body Frame (2EA)
Separate the hoses from the TSG. 
Remove the Body Frame and then, separate theTSG from the washer  

40
10-1. CABINET  & CONTROL PANEL ASSEMBLY
10. EXPLODED VIEW
A105
A201
A220
A303
M410M400