LG Wd 14440fds Owners Manual

30
roduct FeatureP
ontentsC
Warnings ..................................................................................................................31
Specification ..............................................................................................................32
Installation .................................................................................................................33
Care before washing...

31
arningsW
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.                   
READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE 
WARNING!
❊ Do not push down the door excessively, when washer door open.
This could topple over the washer.
• Before installation, check exterior damages. If it has,
do not install. 
• Do not install or store the...

32
pecificationS
Drawer
Inlet hose(1EA)
Spanner
Accessories
Name : Front loading washing machine
Power supply  : 220-240 V~, 50 Hz
Size : 600mm(W) x 640mm(D) x 850mm(H)
Weight : 64 kg  
Wash capacity : 8 kg
Max.Watt : 2100W (Wash) / 1100W (Steam)
Spin speed : /400/600/800/1000/1100/1200 [WD-12440(5)FDS]
/400/600/800/1000/1200/1400 [WD-14440(5)FDS]
/400/600/800/1000/1200/1600 [WD-16440(5)FDS]
Water consumption : 52N(6.5N/ kg)
Permissible water pressure : 0.3-10 kgf/cm
2(30-1000 kPa)
❋The...

33
nstallationI
1. To prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove 
the bolts along with the rubber bungs.
• If they are not removed, it may cause heavy
vibration, noise and malfunction.3. Take out the 4 bolts along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for the future
use.
• Whenever the appliance is transported, the
transit bolts must be refitted.
The appliance is fitted with transit bolts to...

34
nstallationI
Level floor :
Allowable slope under entire washer is 1˚
Power outlet :
Must be within 1.5 meters of either side of location of
washer. Do not overload the outlet with more than one
appliance.
Additional Clearance :
For wall, door and floor modeling is required.
(10cm : rear /2cm:right & left side)
Do not place or store laundry products on top of washer at
any times. 
They can damage the finish or controls.
Installation place requirement
Positioning
Install the washer on a flat hard...

35
nstallationI
Rubber seal Hose connector

36
nstallationI
Normal Tap without thread & screw type inlet hose
Normal Tap without thread & one touch type inlet hose
1.Unscrew the fixing screw to
attach the tap.2.Push the connector up till the
rubber packing is in tight contact
with the tap. Then tighten the 4
screws.3.Push the water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
1.Untighten the upper connector
screw.2.Push the upper...

37
nstallationI
Installation of drain hose
• The drain hose should not be placed higher
than 100 cm above the floor. Water in the
washer does not drain or drains slowly.
• Proper securing of the drain hose will
protect the floor from damage due to water
leakage.
• When the drain hose is too long, do not
force back into the washer. This will cause
abnormal noise.• When installing the drain hose sink,
secure it tightly with a string.
• Proper securing of the drain hose will
protect the floor from damage...

38
nstallationI
Level adjustment
Concrete floors
Wooden floors (Suspended floors)
1. Adjusting the washing machine level properly prevents excessive
noise and vibration.
Install the appliance on a solid and level floor surface, preferably in a
corner of the room.
2. If the floor is uneven, adjust the adjustable feet as required. 
(do not insert pieces of wood etc. under the feet)
Make sure that all four feet are stable and resting on the floor and
then check that the appliance is perfectly level. (use...

39
are before washingC
1. Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment and
how it should be washed.
2. Sorting
To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
Water temperature and spin speed and different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can
occur causing discoloration of white etc. If...