LG Wd 10160n Owners Manual
Have a look at the manual LG Wd 10160n Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1069 LG manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Washing Machine OWNER’S MANUAL WD(M)-10160(5)F WD(M)-80160F WD(M)-65160F Thank you for buying a LG Fully Automatic Washing machine. Please read your owner’s manual carefully, it provides instructions on safe installation, use and maintenance. Retain it for future reference. Record the model and serial numbers of your washing machine.
roduct FeatureP ontentsC 2 Warnings....................................................................................3 Specification ..............................................................................4 Installation..................................................................................5 Care before washing................................................................11 Adding detergent .....................................................................12 Function ...................................................................................13 How to use washer ..................................................................14 Maintenance ............................................................................21 Troubleshooting guide .............................................................24 Terms of Warranty ...................................................................27 Jumbo drum LG’s jumbo drum can wash about 40% more load than conventional washing machines. A bigger drum improves the wash performance. More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption. Child-Lock The Child-Lock system has been used to prevent children from pressing any button to change the program during operation. Low noise speed control system By sensing the amount of load and balance, it evenly distributes load to minimize the spinning noise level. 40%
arningsW 3 For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. ! READ ALL INSTRUCTIONS BEFORE USE WARNING! Do not install or store the washer where it will be exposed to the weather. Do not tamper with controls. Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user-maintenance instructions or published user-repair instructions that you understand and have the skills to carry out. Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc. Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance. Do not leave the washer door open. An open door could entice children to hang on the door or crawl inside the washer. Never reach into washer while it is moving. Wait until the drum has completely stopped. The laundry process can reduce the flame retardant of fabrics. Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry- cleaning solvents, kerosene, etc.) which may ignite or explode. To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions. Do not slam the washer door closed or try to force the door open when locked. This could result in damage to the washer. To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning. Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug. GROUNDING INSTRUCTIONSThis appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance. Do not use an adapter or otherwise defeat the grounding plug. If you don’t have the proper outlet, consult an electrician. IMPORTANT SAFETY INSTRUCTIONS WARNING:To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following: SAVE THESE INSTRUCTIONS WARNING:Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.
pecificationS 4 Power plug Control panel Door Lower cover Adjustable feet (For detergent and fabric softener)Drawer Drum Lower cover cap Drain pump filter Drain plug If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or a similarly qualified person in order to avoid a hazard. Name : Front loading washing machine Power supply : 220-240V~, 50Hz Size : 600mm(W) 600mm(D)850mm(H) Weight / Max.Watt : 67kg / 2200W Wash capacity : 7.0kg Spin speed : No Spin/400/500/650[WD(M)-65160F] No Spin/400/600/800[WD(M)-80160F] No Spin/400/800/1000[WD(M)-10160(5)F] Water consumption : 67 (9.6/ kg ) Permissible water pressure : 0.3-10kgf/ (30-1000kPa) ❋The appearance and specifications may be varied without notice to raise the units quality. Spanner Accessories
nstallationI 5 1. To prevent internal damage during transport, the special 4 bolts are locked. Before operating the washer, remove the bolts along with the rubber bungs. If they are not removed, it may cause heavy vibration, noise and malfunction.3. Take out the 4 bolts along with the rubber bungs by slightly twisting the bung. Keep the 4 bolts and the spanner for future use. Whenever the appliance is transported, the transit bolts must be refitted. The appliance is fitted with transit bolts to prevent internal damage during transport. 2. Unscrew the 4 bolts with the spanner supplied.4. Close the holes with the caps supplied. Transit bolts Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at all times. Any damage which may be cause by cockroaches or other vermin will not be covered by the appliance guarantee. Removing transit bolts cap
nstallationI 6 Level floor : Allowable slope under entire washer is 1 Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance. Additional Clearance : For wall, door and floor modeling is required. (10cm : rear /2cm:right & left side) Do not place or store laundry products on top of washer at any times. They can damage the finish or controls. Installation place requirement Laundry Tub Washer approx. 2cmDrain Hose BS Plug Safety Details (For U.K. User) IMPORTANTTHE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: GREEN AND YELLOW: EARTH BLUE: NEUTRAL BROWN: LIVE This appliance must be earthed As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured Green or Green and Yellow. The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red. If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse. Green and Yellow(Earth) Brown(Live) Blue(Neutral) Cord gripFuseE L N 650 850 600
7 nstallationI Water supply pressure must be between 30kPa and 1000kPa (0.3~10kgf/cm2) Don’t strip or crossthread when connecting Inlet hose to the valve. If the water supply pressure is more than 1000kPa, a decompression device should be installed. Two rubber seals are supplied with the water inlet hoses these are in order to prevent water leaks. Check water tightness of washing machine connections by turning the tap completely on. Periodically check the condition of the hose and replace the hose if necessary. Make sure that there is no kink on the hose and that it is not crushed. When your washer has two valves, The Inlet hose which has red connector is for the hot water tap. If the washer has two valves, the energy is saved by using hot valve. Washing Machine is to be connected to the water mains using new hose- sets and that old hose-sets should not be used. Connecting water supply hose Rubber seal Hose connector Hot water tap Cold Hot(option)Cold water tap 1. Do not use an extension cord or double adapter. 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard. 3. Always unplug the machine and turn off the water supply after use. 4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible. Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service center Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point. If the appliance is delivered in the winter months and temperatures are below freezing : Store the washing machine at room temperature for a few hours before putting it into operation. Electrical connection
8 nstallationI Normal Tap without thread & screw type inlet hose Normal Tap without thread & one touch type inlet hose (Single inlet models) 1.Unscrew the fixing screw to attach the tap.2.Push the connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws.3.Push the water supply hose vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right. 1.Untighten the upper connector screw.2.Push the upper connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws.3. Connect the water supply hose to the middle connector, pushing the plate down. Your machine comes with only cold water connection. Make sure that there are no kinks in the hose and that it is not crushed. Make sure that the rubber seal is inside the hose connector. Upper ConnectorRubber packing Middle connector Fixing screw Guide plate Connector Rubber seal Hose connector Used the horizontal tap Horizontal tap Extension tap Square tap Rubber packing Upper Connector Middle connectorPlateUpper Connector Water supply hose In case the diameter of the tap is large remove the guide plate. Turn the middle connector not to have water leaked. To separate the water supply hose from the middle connector shut off the tap. Then pull the inlet hose down, pushing the plate down.
9 nstallationI Installation of drain hose max. 100 cm min. 60 cmca. 105 cmca. 145 cmca. 100 cm max. 100cm min. 60cm Hose Retainer Laundry tub Tie strapmax. 100cm min. 60cm max. 100 cm ca. 105 cm ca. 145 cm ca. 100 cm min. 60 cm The drain hose should not be placed higher than 100 cm above the floor. Proper securing of the drain hose will protect the floor from damage due to water leakage. When the drain hose is too long, do not force back into the washer. This will cause abnormal noise. When installing the drain hose sink, secure it tightly with a string. Proper securing of the drain hose will protect the floor from damage due to water leakage. This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of suffocation ! Keep all packaging well away from children