LG Wd 10160n Owners Manual

P/No.: 3828ER3014P
 

Washing Machine
OWNER’S MANUAL
WD(M)-10160(5)F 
WD(M)-80160F
WD(M)-65160F
 
Thank you for buying a
LG Fully Automatic Washing machine.
Please read your owner’s manual carefully, it provides
instructions on safe installation, use and maintenance.
Retain it for future reference.
Record the model and serial numbers of your washing machine.
 

roduct FeatureP
ontentsC
2
Warnings....................................................................................3
Specification ..............................................................................4
Installation..................................................................................5
Care before washing................................................................11
Adding detergent .....................................................................12
Function...

arningsW
3
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.                   !
READ ALL INSTRUCTIONS BEFORE USE
WARNING!
 Do not install or store the washer where it will 
be exposed to the weather.
 Do not tamper with controls.
 Do not repair or replace any part of the washer 
or attempt any servicing unless specifically
recommended in the user-maintenance...

pecificationS
4
Power plug
Control panel
Door
Lower cover
Adjustable feet
(For detergent and 
fabric softener)Drawer
Drum
Lower cover cap
Drain pump filter
Drain plug
  If the supply cord is damaged,
  it must be replaced by the 
manufacturer or its service agents 
or a similarly qualified person in 
order to avoid a hazard.
Name : Front loading washing machine
Power supply  : 220-240V~, 50Hz
Size : 600mm(W)
600mm(D)850mm(H)
Weight / Max.Watt : 67kg / 2200W
Wash capacity : 7.0kg
Spin speed : No...

nstallationI
5
1. To prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove 
the bolts along with the rubber bungs.
 If they are not removed, it may cause heavy
vibration, noise and malfunction.3. Take out the 4 bolts along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future use.
 Whenever the appliance is transported, the
transit bolts must be refitted. The appliance is fitted with transit bolts to...

nstallationI
6
Level floor :
Allowable slope under entire washer is 1
Power outlet :
Must be within 1.5 meters of either side of location
of washer. Do not overload the outlet with more
than one appliance.
Additional Clearance :
For wall, door and floor modeling is required.
(10cm : rear /2cm:right & left side)
Do not place or store laundry products on top of
washer at any times. 
They can damage the finish or controls.
Installation place requirement
Laundry
Tub Washer
approx.
2cmDrain Hose
BS Plug...

7
nstallationI
Water supply pressure must be between
30kPa and 1000kPa (0.3~10kgf/cm2)
Don’t strip or crossthread when connecting
Inlet hose to the valve.
If the water supply pressure is more than
1000kPa, a decompression device should be
installed.
 Two rubber seals are supplied with the
water inlet hoses these are in order to
prevent water leaks.
 Check water tightness of washing
machine connections by turning the tap
completely on.
 Periodically check the condition of the
hose and replace the hose...

8
nstallationI
Normal Tap without thread & screw type inlet hose
Normal Tap without thread & one touch type inlet hose (Single inlet models)
1.Unscrew the fixing screw to
attach the tap.2.Push the connector up till the
rubber packing is in tight contact
with the tap. Then tighten the 4
screws.3.Push the water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
1.Untighten the upper connector...

9
nstallationI
Installation of drain hose
max. 100 cm
min. 60 cmca. 105 cmca. 145 cmca. 100 cm
 
max. 100cm
min. 60cm
Hose
Retainer Laundry tub
Tie
strapmax. 100cm
min. 60cm
max. 100 cm
ca. 105 cm ca. 145 cm ca. 100 cm
min. 60 cm
 The drain hose should not be placed
higher than 100 cm above the floor.
 Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
 When the drain hose is too long, do
not force back into the washer. This
will cause abnormal noise. When...