LG W3000h Users Guide

							A10
Troubleshooting
No image appears
Check the following before calling for service.
No image appears
Is the power cord of the
display connected?
Is the power on and the
power indicator blue or
green?
Is the power indicator
amber?• Check and see if the power cord is connected
properly to the power outlet.
• Adjust the brightness and the contrast.
• If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard to
bring up the screen.
• Try to turn on the PC.
Important
Check Control Panel --> Display --> Settingsand see if the frequency or the
resolution were changed. If yes, readjust the video card to the recommend
resolution.
Reasons for Recommending Optimal Resolution: The aspect ratio is 16:10. 
If the input resolution is not 16:10 (for instance, 16:9, 5:4, 4:3), you might encounter
problems such as blurred letters, blurry screen, cut-off screen display or tilted 
screen. 
The setting method can differ by computer and O/S (Operation System), 
and resolution mentioned above may not be supported by the video card    
performance. In this case, please ask to the computer or the video card  
manufacturer
. 
 
						

							A11
Have you installed the display driver?
Have you installed the
display driver?
Do you see an
Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found
message?
• Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lge.com.
• Make sure to check if the video card supports
Plug&Play function.
Display image is incorrect
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Troubleshooting
 
						

							A12
Specifications        
Display
Sync Input
Video Input
Resolution
Plug&Play
Power
Consumption
Dimensions
&Weight
Tilt Range
Power Input
Environmental
Conditions30 inches (75.6228cm) Flat Panel Active matrix-TFT LCD 
Anti-Glare coating 
30 inches viewable
0.2505 mm pixel pitch
Horizontal Freq. 98.71kHz (Automatic)
Vertical Freq. 59.97 Hz (Automatic)
Input Form Digital(HDCP)
Signal Input DVI - D connector (Digital)
Input Form Digital
M ax VESA 2560 x 1600 @ 60 Hz
Recommend VESA 2560 x 1600 @ 60 Hz
DDC 2B
On Mode: 130W(Typ.),140W(USB Full load)
Sleep Mode≤2 W
Off Mode≤1 W
With Stand Without Stand
Width
70.27 cm / 27.67 inches 70.27 cm / 27.67 inches
Height52.54 cm / 20.69 inches(Min) 47.65 cm / 18.76 inches
62.54 cm / 24.62 inches(Max)
Depth27.02 cm / 10.64 inches 8.30 cm /   3.27 inches
Net 12.3kg (27.12 lbs)
Tilt -5˚~20˚
Swivel range              350˚
Height  range            100 mm / 3.94 inches
AC 100-240V~ 50/60Hz 1.5A 
Operating Conditions
Temperature 10˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity 5 % to 90 % non-Condensing
 
						

							A13
Specifications        
NOTE
Information in this document is subject to change without notice.
Attached (     ), Detached ( O )
Wall-outlet type or PC-outlet type
Standard                     USB 2.0, Self-Power 
Data Rate                Max 480 Mbps
Power Consumption  Max 2.5W x 4Stand Base 
Power cord 
USB
 
						

							A14
Specifications
Preset Modes (Resolution)
*Recommend Mode
Display Modes (Resolution)
Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
*21280 x 800 
2560 x 160049.310
98.71360
60
Indicator
On Mode
Sleep Mode
Off ModeBlue
Amber
Off
LED Color
MODE
 
						

							A15
Installing the Wall mount plate
This monitor satisfies the specifications of the  Wall mount plate or
the interchange device.
Wall mount plate(Separate purchase)
This is stand-type or wall mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more
details, which is provided when Wall mount plate
is purchased.
Kensington Security Slot
Connected to a locking 
cable that can be purchased
separately at most 
computer stores.
1.After moving the product to face
downward, make sure to place it on
a soft cloth or a cushion to avoid
surface damage.  
2. Remove the screw by using a
screwdriver, and pull the Stand
part in the arrow direction. 
Then the Head and Stand parts
are separated.
3.Install the Wall mount plate.
 
						

							Digitally yours