LG W2363d Owners Manual

							20
Troubleshooting
No image appears
Check the following before calling for service.
No image appears
Do you see a OSD LOCKED message on the screen?
• You can secure the current control settings,
so that they cannot be inadvertently changed.
You can unlock the OSD controls at any time
by pushing the MENUbutton for several
seconds: the message “OSD UNLOCKED”
will appear. Do you see “OSD
LOCKED” when you
push MENU button?
Is the power cord of the
display connected?
Is the power indicator
light on?
Is the power indicator
blinking?
Do you see an OUT OF
RANGE message on
the screen?
Do you see a CHECK
SIGNAL CABLE
message on the
screen?• Check and see if the power cord is connected
properly to the power outlet.
• Press the Power button.
• If the display is in power saving mode, try
moving the mouse or pressing any key on the
keyboard to bring up the screen.
• Try to turn on the PC.
• This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
Specifications section of this manual and
configure your display again.
• This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try
again.
 
						

							21
Display image is incorrect
Do you see an Unrecognized monitor, Plug&Play (VESA DDC)
monitor found message?
The Audio function is not working
IMPORTANT
Check Control Panel --> Display --> Settingsand see if the frequency or the resolution were
changed. If yes, readjust the video card to the recommend resolution.
If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the
screen may be dimmed, truncated or biased. Make sure to select the recommend resolution. 
The setting method can differ by computer and O/S (Operation System), and resolution mentioned
above may not be supported by the video card performance. In this case, please ask to the
computer or the video card manufacturer. 
Troubleshooting
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true
color) at Control Panel - Settings.
• Check if the screen is set to interlace mode and
if yes, change it to the recommend resolution.
Have you installed the
display driver?• Be sure to install the display driver from the
display driver CD (or diskette) that comes with
your display. Or, you can also download the
driver from our web site: http://www.lg.com.
• Make sure to check if the video card supports
Plug&Play function.
Picture OK & No sound.• Check whether volume is 0.
• Check whether the cable is correctly connected. 
(DVI-D cable, HDMI cable, Headphone cable, 
Audio cable)
• Check sound format. Not supply to compressed
sound format.
 
						

							22
Specifications
58.4 cm (23.0 inch) Flat Panel Active matrix-TFT LCD 
Anti-Glare coating 
Visible diagonal size: 58.4 cm
0.266 mm x
0.266 mm (Pixel Pitch)
Horizontal Freq. Digital: 30 kHz to 141 kHz
HDMI:  30 kHz to 83 kHz
Vertical Freq.Digital: 56 Hz to 120 Hz
HDMI:  56 Hz to 61 Hz 
Input FormDigital (HDCP, Separate Sync.) 
Signal Input DVI-D Connector (Digital)
19 pin HDMI Connector (Digital)
Input Form Digital, HDMI
MaxVESA1920 x 1080 @ 120 Hz
RecommendVESA 1920 x 1080 @ 60 Hz (2D)
Recommend 1920 x 1080 @ 120 Hz (3D)
DDC 2B (Digital, HDMI)
On Mode : 49 W (Typ.)
Sleep Mode≤1.6 W (DVI-D / HDMI)
Off Mode≤1 W
With Stand Without Stand
Width     55.55 cm (21.87 inch) 55.55 cm (21.87 inch)
Height 41.92 cm (16.50 inch)     40.95 cm (16.12 inch)  
Depth 20.60 cm (  8.11 inch) 7.33 cm (  2.88 inch)
Weight(excl. packing) 5.2 kg (11.46 lb) 
-5˚ to 15˚
AC 100-240 V~ 50/60 Hz 0.8 A
Operating Conditions
Temperature 10 ˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20 ˚C to 60 ˚C
Humidity 5 % to 90 % non-Condensing
Attached (     ), Detached ( O )
Wall-outlet typeDisplay
Sync Input
Video Input
Resolution
Plug&Play
Power
Consumption
Dimensions
& Weight
Tilt Range
Power Input
Environmental
Conditions
Stand Base 
Power cord 
NOTE
Information in this document is subject to change without notice.
 
						

							23
Specifications
Indicator
On Mode
Sleep Mode
Off ModeBlue
Blue Blinking 
Off
LED Color
MODE
Preset Modes (Resolution) - DVI-D(Digital) INPUT
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
12
13
*14
**15
**16
**17640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680 x 1050
1680 x 1050
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 108031.469
31.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
64.674
65.290
67.500
113.721
125.668
137.86070
70
60
75
60
75
60
75
75
60
75
60
60
60
100
110
120
*Recommend Mode
**3D Mode output
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8480P
576P
720P
720P
1080i
1080i
1080P
1080P31.50
31.25
37.50
45.00
28.12
33.75
56.25
67.5060
50
50
60
50
60
50
60
HDMI Vedio INPUT
 
						

							24
Installing the Wall mount plate
This monitor satisfies the specifications of the  Wall mount plate
or the interchange device.
1.Place the monitor face down on the soft cloth.
2.To disconnect the Stand Base from the Stand Body, unfold the screw handle and
turn it to the left.
3.Pull out the Stand Base to remove. 
 
						

							Installing the Wall mount plate
25
4.Install the Wall mount plate.
Wall mount plate(Separate purchase)
This is stand-type or wall mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more details,
which is provided when Wall mount plate is
purchased. 
Kensington Security SlotConnected to a locking cable that
can be purchased separately at
most computer stores.Hole spacing : 100 mm x 100 mm.
NOTE
VESA compatible only with respect to screw mounting interface dimensions and mounting screw     
specifications
Please use VESA standard as below.
* 784.8 mm and under (30.9 inch) 
- Wall Mount Pad Thickness :  2.6 mm
- Screw :   4.0 mm x Pitch 0.7 mm x Length 10 mm    
* 787.4 mm and above (31.0 inch) 
- Please use VESA standard wall mount pad and screws. 
Wall Mount pad
 
						

							Make  sure  to  read  the  Important  Precautions before using the product.Keep  the  User ’s  Guide(CD)  in  an  accessible place for furture reference.The  model  and  serial  number  of  the  SET  is located on the back and one side of the SET. Record it below should you ever need service.
MODEL
SERIAL