LG W2363d Owners Manual

www.lg.com
OWNER’S MANUAL
LCD MONITOR 
LCD MONITOR MODELS
W2363D
Please  read  this  manual  carefully  before  operating  your  set  and 
retain it for future reference.
ENGLISH
   

1
This unit has been engineered and manufactured to ensure your personal safety,
however improper use may result in potential electrical  shock or fire hazards. In
order to allow the proper operation of all safeguards incorporated in this display,
observe the following basic rules for its installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may...

Important Precautions
3
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a soft
cloth to prevent scratching. Do not clean with a wet cloth or spray water or other
liquids directly onto the product. An electric shock may occur. (Do not use
chemicals such as benzene,...

4
Accessories
!!! Thank for selecting LGE products !!! 
Please make sure the following items are included with your
monitor. If any items are missing, contact your dealer.
OWNERS MANUAL/CardsPower Cord
(Depending on the country)
DVI-D Signal Cable(Dual)
IMPORTANTThis accessories may look different from those shown here.
User must use shielded signal interface cables (DVI-D cable) with ferrite cores to maintain
standard compliance for the product.
Requirements for 3D (3 Dimensional) imagery
1. NVIDIA®...

5
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off. 
Connecting and Disassembling the stand
1.Place the monitor face down on the soft cloth.
2.Assemble the Stand Baseinto the Stand Bodyin the correct direction.
Make sure you push the Stand Baseuntil the end.
Stand Base Stand Body
The Stand Basemay
fall and get damaged
or cause injury.
Good ConnectionBad Connection
 

6
Connecting the Display
IMPORTANTThis picture depicts the general model of connection. Your monitor may differ from the
items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may fall
and get damaged or cause injury.
4.Then fold the screw handle flat. 5.Once assembled take the monitor
up carefully and face the front side.
6.To disconnect the Stand Basefrom the Stand Body, unfold the screw handle
and turn it to the left. 
3.Turn the screw to the right to...

7
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor,
the computer system, and other attached devices is turned off. 
Positioning your display
After installation, adjust the angle as shown below. 
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range:-5˚  to 15˚                            
ERGONOMIC
It is recommended that in order to maintain an ergonomic and comfortable viewing position,
the forward tilt angle of the monitor should not...

8
Connecting the Display
AConnect DVI-D (Digital signal) Cable
Connect HDMI Cable (HDMI1, HDMI2)
1.Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.  
2.Connect signal input cable         and power cord        in order, then tighten the
screw of the signal cable.
Connecting with the PC/AV equipment
12
NOTEThis is a simplified representation of the rear view.
This rear view represents a general model; your display may differ...

9
Control Panel Functions
Front Panel Controls
MENU ButtonUse this button to enter or exit the On Screen Display.
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU buttonfor several seconds.
The message OSD LOCKEDshould appear.
You can unlock the OSD controls at any time by pushing
the MENU buttonfor several seconds. The message
OSD UNLOCKEDshould appear.
ButtonUse this button to enter THRU MODE, SRS...