LG Projector PH150G User Manual

							31
•	When using the remote control, the optimal 
operation range is 6 meters or less (left/right) 
and within a 30 degree arc of the remote control 
IR receiver.
•	 If a cable is connected to the back port, the 
optimal operating range is 3 meters or less (left/
right) and within a 30 degree arc of the remote 
control IR receiver.
•	 For seamless operation, do not block the IR 
receiver.
•	 When you carry the remote control in the portable bag, make 
sure that the buttons on the remote control are not pressed by the 
projector, cables, documents, or any other accessories in the bag. 
Otherwise, it may significantly reduce the battery life.
NOTE
30°   30°
ENGLISH  
						

							32
USING	THE	PROJECTOR
Using	The	Battery
 
The battery is low. Connect a power 
supply for charging.
•	It is displayed when the battery is low (Energy Saving mode will be changed to Maximum and will be disabled).
•	If the screen shows a low battery message, be sure to charge the battery.
 
The device powers off due to insufficient 
battery.
•	It is displayed when the battery is running out.
•	As your battery is running out, the projector will turn off immediately.\
•	If the battery runs out, the projector can only be turned on after it ha\
s been connected to a power supply.
ENGLISH  
						

							33
Battery	using	time	information
StatusTime and Display
ChargingAbout 3 hours (When in standby and charging)
Usage	Hours
Up to 2.5 hours
(Available battery using time up to 2.5 hours when Energy Saving mode set to Max.)
Battery 	Level	IndicatorStep 5
Step 4
Step 3
Step 2
Step 1 FullStep 1Step 2 Step 3 Step 4 Step 5 Full
•	If you do not intend to use the projector for a long time, leave the bat\
tery charged at 40 % to 50 %.
•	The battery is automatically recharged when the projector is connected to a power supply.
•	Charge the battery fully when you first use the projector.
•	The battery standard usage time given in the manual is based on measurements taken by LG; the actual time may vary depending upon usage.
•	Battery usage time may vary depending on broadcast type, operating temperature, period of use, and user preferences.
•	As the battery is consumable, its lifetime gradually decreases. When the\
 battery’s life is reduced by half, replace it with a new battery from\
 an LG Electronics Customer Support Center.
•	Do not charge the battery using any equipment other than that supplied with the product. This may damage the battery or cause a fire.
•	Always use a battery that is approved and certified by LG Electronics, Inc. Failure to do so may result in an explosion or fire.
•	If the battery is leaking or giving off an odor, discontinue its use immediately and contact LG Electronics Customer Support Center.
•	The battery contains lithium-ion, so please handle with care. Failure to\
 do so may result in an explosion or fire.
ENGLISH  
						

							34
Watching	Projector
Turning	on	the	Projector
The menu screen display in this owner's manual is an example to help users understand how to operate the product and may look different from the actual screen.
1 Connect the power cord correctly.
2 Place the ON/OFF switch on the rear port area to ON and press the 
(POWER) button on the joystick button or on the remote control. (If 
the switch is placed to OFF, the projector will not turn on.) 
3 In the Language Selection screen, select a language.
4 In the Mode	Setting screen, select the setting mode you want.
Mode Setting
Selecting the environment.
Choose the setting mode you want.
Select [Standard] to use this Projector at home. To use this 
Projector at store, select [Store Demo].   
	Confirm	 Previous
Standard Store Demo
Demo ModeOff
*  Store	Demo is used when displaying the product in-store. The picture mode is automatically reset after a certain period of time. You can select Standard to use the product at home.5 Select an input signal by using the  button on the remote control.
ENGLISH  
						

							35
Focus	of	the	Screen	Image
When an image appears on the screen, check if it is in focus and fits the screen properly.
Adjust the focus of the image by rotating the Focus Ring to the left or \
right.
Make sure the product does not move when adjusting the focus.
Focus Ring
Watching	With	the	Projector
1 When in standby mode, press the (POWER) button to turn the projector on.
2 Press the  button and select the input signal you want.
3 Control the projector using the following buttons while watching projector.
ButtonDescription
Adjusts the volume level.
Mutes all sounds.
Accesses the quick menu.
Resizes an image.
Adjusts Keystone.
4 To turn the projector off, press the (POWER) button.
ENGLISH  
						

							36
Additional	Options
Adjusting	Aspect	Ratio
Resize an image to view at its optimal size by pressing  while you are using the projector.
•	Available picture size may differ depending on the input signal.
•	 You can also use the 
 or 	button.
NOTE
MenuDescription
16:9Resizes images to the 16:9 ratio.
Just	Scan
Displays video images in the original size without removing parts of the edge of the image.
•	If you select Just	Scan, you may see image noise at the edge or edges of the screen.
Set	By 	ProgramDisplays images in the same aspect ratio as the original image.
4:3Resizes images to the previous standard 4:3.
Zoom
Resizes the image to fit the screen width. The top and bottom parts of the image may be cut off.
•	Press the  or  button to zoom in or out of the image.
•	Press the  or  button to move the image.
Cinema 	Zoom	1
Formats an image to the cinemascope ratio, 2.35:1.  It ranges from 1 to 16.
•	Press the  or  button to zoom in or out of the image.
•	Press the  or  button to move the image.
•	If you enlarge or reduce an image, the image may be distorted.
ENGLISH  
						

							37
Using	the	Keystone	Function
To prevent the screen image from becoming trapezoidal, Keystone adjusts the top and bottom width of the image if the projector is not se\
t up at a right angle to the screen.
Because the Keystone function may cause inferior screen image quality, use this function only when it is not possible to set up the projector a\
t an optimal angle.
• Keystone    0◀-  +▶
	OK
1 Press the Key's	, or Key's	, button to adjust the picture.
•	Keystone can be adjusted from -40 to 40.
2 Press the 	button when done.
ENGLISH  
						

							38
Changing	Input	Device
To	select	an	external	input
Selects external input.
The illustration of the menu may differ from the actual screen on the product.
•	Press the  button on the remote control to display the input selection screen. -Connected inputs are displayed first. However, SCREEN	SHARE input is always activated.
•	Select an input signal using the remote control's  button to connect the projector to the desired input.You can use the  or  button to switch between all the input modes.

Input List
SCREEN SHAREUSBHDMI
ꔂ Move ꔉ OK
Exit
Input Label
ENGLISH    
						

							39
Selecting	an	Input	Label
Displays which devices are connected to which input ports.
Input Label
HDMI
Close
1 Press the  button on the remote control to display the input selection screen.
2 Press the Red button.
3 Use the  or  button to select one of the input labels.
ENGLISH  
						

							40
Blank	Function
Using	the	Blank	Function
This function may be effective when you need to draw attention during a meeting or training.
1 Press the  button, and the screen is covered by the background color. You can change the background color by referring to Selecting a Blank Image.
2 Press any button to clear the blank function. To cover the screen temporarily, press the  button on the remote control. Do not block the lens with any object while the projector is running. It may become overheated and deformed or even cause a fire.
Selecting	a	Blank	Image
1 Press the 	button.
2 Press the  ,  ,  , or  buttons to select OPTION	2 and press 
the 	button.
3 Press the  ,  buttons to select Blank	Image and press the button.
4 Press the  or  button to move to the setting or option you want and press the 	button.
ENGLISH