LG Projector Minibeam UST PF1000U User Manual

							31USING	THE	PROJECTOR
USING	THE	PROJECTOR
Connecting	the	Antenna	or	Cable
To watch TV using an indoor/outdoor antenna, connect a wall terminal and the antenna port of the Projector using an RF cable (75 Ω).
You can watch terrestrial or cable (analog, digital) TV. (The RF cable is sold separately.)
 
•	Make sure not to bend the copper wire of 
the RF cable (75 Ω). Turn the input jack to 
the right to fasten it.
•	 Ensure you use a standard coaxial cable 
(75 Ω, sold separately) when connecting to 
the projector input.
•	 For better image quality in locations where 
signal strength is low, purchase and install a 
signal amplifier (booster).
•	 A signal splitter is required if you want to use two or more 
projectors through one antenna.
•	 If you have any problems when installing the antenna, please 
consult a suitable retailer or the store where you purchased the 
antenna.
NOTE
Copper wire  
						

							32USING	THE	PROJECTOR
Watching	Projector
Initial	Setup
The menu screen display in this owner's manual is an example to help users understand how to operate the product and may look different from the actual screen.
1	Connect the power cord correctly.
2	After waiting for a moment, press the POWER button on the remote control or the joystick button. 
3	When you turn on the projector for the first time, a setting screen appears as shown below. Here, you can specify the items required for watching the projector more easily.
 –Store	mode is used when displaying the product in-store. The picture mode is automatically reset after a certain period of time. You can select Home to use the product at home.  
						

							33USING	THE	PROJECTOR  
						

							34USING	THE	PROJECTOR
 –The initial settings are completed when you select the settings above.
•	For  Auto	Tuning while using the projector, go to  (Home) → 
SETTINGS → CHANNEL and select Auto	Tuning.
•	 To change the mode while using the projector, go to 
 (Home) → 
SETTINGS → OPTION and select Mode	Setting.
NOTE  
						

							35USING	THE	PROJECTOR
Focus	of	the	Screen	Image
When an image appears on the screen, check if it is in focus and fits the screen properly. 
Focus Ring
•	To adjust the focus of the image, rotate the focus ring.
•	Make sure the product does not move when adjusting the focus.
Watching	With	the	Projector
1	When in standby mode, press the POWER button to turn the projector on.
2	Select the  (Home) → INPUT	LIST and select the input signal you want.
3	Control the projector using the following buttons while watching projector.
ButtonDescription
	CHChanges the TV channel.
 VOLAdjusts the volume level.
 (MUTE)Mutes the sound from the projector.
4	To turn the projector off, press the POWER button.   
						

							36USING	THE	PROJECTOR
To	Set	Channel
Image shown may differ from your projector.
To	View	Program	Information
Displays information on current program and / or current time, etc.
1	Move the pointer of the Magic Remote control to the top of the projector\
 screen.
2	Click the activated channel banner area.
3	The program details will be displayed at the bottom of the projector screen.
	1		2		3	
Description
	1	Program name
	2	Current time
	3	Detail information on program (for digital broadcast)
To	Set	Favorite	Channels
 (Home) → SETTINGS → CHANNEL → Channel	Edit
1	Move to the desired channel on  Wheel	(OK) button. Channel is selected.
2	Press Set	as	Favorite.
3	Select the desired Favorite channel group.
4	Select OK. Favorite is set.  
						

							37USING	THE	PROJECTOR
To	Use	Favorite
 (Home) → MY	APPS → Ch.	List
Channel list will appear. Select the desired preset favorite channel fro\
m Favorite List A to D.
To	Set	Auto	Tuning
 (Home) → SETTINGS → CHANNEL → Auto	Tuning 	
Automatically tunes the channels. 
•	Channels are not registered properly unless the antenna / cable is connected correctly. 
•	Auto	Tuning only sets channels that are currently broadcasting. 
•	If Lock	System is turned on, a pop-up window will appear asking for password.
To	Set	Channels	Manually
 (Home) → SETTINGS → CHANNEL → Manual	Tuning
Adjusts channels manually and saves the results. 
For digital broadcasting, signal strength, etc. can be checked. 
To	Edit	Channels	
 (Home) → SETTINGS → CHANNEL → Channel	Edit 	
Edits the saved channels 
Set your selected channel as favorite, block / unblock, and Add / Delete\
.  
						

							38USING	THE	PROJECTOR
Additional	Options
To	adjust	Aspect	Ratio	
Select  (Home) → SETTINGS → PICTURE → Aspect	Ratio
Selects the screen aspect ratio. 
MenuDescription
16:9Resizes images to fit the screen width.
Just	Scan
Displays video images in the original size without removing parts of the edge of the image. 
•	In DTV / HDMI / Component (over 720p) mode, Just	Scan is available.
Set	By 	ProgramDepending on the input signal, screen aspect ratio changes to 4:3 or 16:9.
4:3Resizes images to the previous standard 4:3.
ZoomResizes the image to fit the screen width. The top and bottom parts of the image may be cut off.
Cinema 	Zoom	1Formats an image to the cinema scope ratio (2.35:1) and zooms in on the ratio.
•	While viewing an external device, these cases may result in image 
burn :
 
– a video with stationary caption (such as network name)
 
– 4:3 aspect ratio mode for an extended period.
Take caution when using these functions. 
•	 Available picture size may differ depending on the input signal. 
•	 The screen aspect ratios on HDMI-PC input are available in 4:3 and 
16:9 only.
NOTE  
						

							39USING	THE	PROJECTOR
Using	the	Edge	Adj	(4	Corner	Keystone)	Function
Edge	Adj (4 Corner Keystone) adjusts the horizontal and vertical sides of the projected image if the projector is at an angle and not perpendicula\
r to the screen. This feature ensures the shape of the projected image is not\
 distorted.
Use this feature only when the projector cannot be set up at the optimal\
 angle. Edge	Adj may result in a loss of image quality.
1	Go to  (Home) → SETTINGS → OPTION → Edge	Adj.
2	The value range of Edge	Adj is as follows. –Top Left (H: 0 to 100, V: 0 to 100)
 –Top Right (H: -100 to 0, V: 0 to 100)
 –Bottom Left (H: 0 to 100, V: -100 to 0)
 –Bottom Right (H: -100 to 0, V:-100 to 0)
3	Press the  Wheel	(OK) button.
•	When using Auto	Keystone(Vertical), the current value set for 
Edge	Adj is changed to the value that has been set with Auto 	
Keystone(Vertical).
NOTE  
						

							40USING	THE	PROJECTOR
Changing	Input	Device
To	select	an	external	input
Selects external input.
•	Select  (Home) → INPUT	LIST or press the INPUT button on the remote control to display the input selection screen. –Connected inputs are displayed first. However, AV is always activated.
•	Select an input signal using the remote control's INPUT button to connect the projector to the desired input. You can use the  or  button to switch among all the input modes.
	1	
	2	
	3		4		5	
Description
	1	Selects speaker.
	2	Selects input.
	3	Edits the name of external device connected to external terminal.
	4	Sets SIMPLINK.
	5	Sets Universal	Remote	Control.