LG Projector Minibeam UST PF1000U User Manual

21PREPARATION
Back
	1		2		3	
No.Description
	1	 Port
	2	DC IN Port
	3	 Port  

22PREPARATION
Using	the	Joystick	Button
You can operate the projector by pressing the button or moving the joyst\
ick left, right, up, or down.
Basic	functions
Power	OnWhen the projector is turned off, place your finger on the joystick button, press it once, and release it.
Power	OffWhen the projector is turned on, place your finger on the joystick button, press it once for a few seconds, and release it. (However, if the Menu button is on the screen, pressing and holding the joystick button will let you...

23PREPARATION
Adjusting	the	menu
When the projector is turned on, press the joystick button one time.
You can adjust the menu items (, , , ) moving the joystick button left, right, up, or down. Move to the desired menu item, and then\
 press the joystick button once to select it.
Close
Projector	offTurns the power off.
Input	ListChanges the input source.
CloseClears on-screen displays and returns to projector viewing.
SettingsDisplays the Settings menu.
Projector	Status	Indicators
LED Power Indicator
LED...

24PREPARATION
Installation
Installation	Precautions
•	Place the projector in a well-ventilated environment. –To prevent internal overheating, install the projector in a well-ventilated place. Do not place anything near the projector. That may block its air vents. If the air vents are blocked, the internal temperature of the projector will increase.
 –Do not place the projector on a carpet or rug. If the projector's inlet vent is on the bottom, be careful not to block the vent and always use the...

25PREPARATION
Projection	Distance	per	Screen	Size
1	Place the projector on a sturdy, level surface, together with the PC or audio/video source.
2	Place the projector an appropriate distance away from the screen. The distance between the projector and the screen determines the actual size of the image.
3	Position the projector so that the lens is at a right angle to the scree\
n. If the projector is not at a right angle, the projected image will look distorted. To correct the distortion, use the Edge Adj...

26PREPARATION
Kensington	Security	System
•	This projector has a Kensington Security Standard connector as an anti-theft mechanism. Connect a Kensington Security System cable as shown below.
•	For more information on installation and use of the Kensington Security System, refer to the user’s guide provided with the Kensington Securi\
ty System.
•	The Kensington Security System is an optional accessory.
•	What is Kensington? Kensington is a company that provides safety systems for laptops and other...

27MAGIC	REMOTE	CONTROL
MAGIC	REMOTE	CONTROL
If the battery low message appears while using the Projector, replace the batteries.
As shown in the figure, press the top of the battery cover and slide it down the cover. Insert two new and identical batteries (1.5 V, AA type) with + and - poles pointing in the correct direction in the remote control.2
1
•	Do not mix new batteries with old ones.
NOTE
	(POWER)
Turns the Projector on or off.
	(Up/Down/Left/Right)
Press the up, down, left or right button to...

28MAGIC	REMOTE	CONTROL
	(EXIT	to	LIVE)
Switches among broadcast (antenna) and various inputs.
	(Voice	recognition)
Network connection is required to use the voice recognition function.1. Press the voice recognition button.2.  Speak when the voice display window appears on the left of the Projector screen.*  Use the Magic Remote no further than  10 cm from your face.*  The voice recognition may fail when you speak too fast or too slowly.*  The recognition rate may vary depending on the user’s...

29MAGIC	REMOTE	CONTROL
	1	
	2	
	1	Displayed when you press the  Wheel	(OK) button on the magic remote control. Check program information.
	2	If you point and hold the pointer at the bottom left of the screen while watching projector, the MY	APPS icon is displayed. Clicking the icon displays the MY	APPS menu.
To	Register	the	Magic	Remote	Control
To use the Magic Remote control, register it with your projector first.
1	Put batteries into the Magic Remote and turn the Projector on.
2	Point the Magic Remote...

30MAGIC	REMOTE	CONTROL
Using	the	Magic	Remote	Control
•	Shake the magic remote control lightly when there is no pointer displayed on the screen. A pointer will be displayed on the screen. –The pointer disappears if the remote control is not used for a certain period of time.
•	When you move the pointer signal transmitter up/down/left/right while pointing it toward the projector, the pointer moves. –If the pointer is not working properly, do not move the magic remote control for about  10 seconds, and...