LG Hs200 Projector User Manual

Installing and Composition12
Installing and Composition
Provide proper ventilation for this projector.
•   
The projector is equipped with ventilation holes(intake) on 
the bottom and ventilation holes(exhaust) on the front. Do 
not block or place anything near these holes. Internal 
heat build-up may occur, causing picture degradation or 
damage to the projector.
Place this projector in adequate temperature and humidity conditions.
•  Install this projector only in a location where adequate temperature...

Installing and Composition
13
1. Place the projector on a sturdy and horizontal surface with the PC or AV source.
2.    Place the projector with the desired distance from the screen. The distance between the projector and the screen 
determines the actual size of the image. 
3.    Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right 
angle, the screen image will be crooked. Although, slight angles can be counteracted using the Keystone...

Installing and Composition14
•  
This projector has a Kensington Security System Connector on the side panel. Connect the Kensington Security System 
cable as below.
•    For the detailed installation and use of the Kensington Security System, refer to the user’s guide included with the 
Kensington Security System set. And for further information, contact  http://www.kensington.com, the internet homepage 
of the Kensington company that deals with expensive electronic equipment such as notebook PCs or...

Installing and Composition
15
Selecting input mode
1. Press the  INPUT button on the top cover or the  INPUT button on the remote control. 
2.    Selecting an input signal with the  INPUT button will only change the projector only to connected inputs. You can 
change it to any inputs with the  ＜, ＞  button.
•  The component input is always active, and it does not support plug &play function.
Input List
Component VideoRGBHDMI
Turning on the Projector
1. Make sure the power cord is connected correctly.
2....

Connection16
Connection
Connecting to a Desktop PC
* You can connect the projector to a computer with VGA, SVGA, XGA, SXGA output. 
* Refer to page 39 for resolutions the projector supports.
< How to connect >
1.    Connect the  RGB IN of the projector and the computer 
output port with a computer cable.
2.    
Connect the  AUDIO IN of the projector and the computer 
audio output port with an audio cable.
  *  
You may have to change the resolution that your PC exports to 
one supported by the projector....

Connection
17
Connecting to a DVD Player
< How to connect a Component source >
1.   After connecting the Component cable of DVD Player to 
the RGB to Component cable, connect it to the  RGB IN 
terminal of the projector.  
  *   When connecting the component cable, match the jack colors 
with the component cable.(Y=green, PB=blue, PR =red)
2.    Connect the  AUDIO IN of the projector to the output jacks 
of the audio source with an audio cable.
< How to connect a HDMI source >
1.
   Connect the  HDMI in...

Function18
PICTURE Menu Options
1.  
Press the  MENU button. Then, move to  PICTURE with 
the  ∧, ∨ , ＜ , ＞  buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to a desired function 
and press the  ◉OK  button.
3.   
Press the  ＜, ＞  buttons to make a desired adjustment 
and then press the  ◉OK  button.
• You can set image values differently for each input and  Picture Mode.
•   
Saving after making adjustments will display  (User) in adjusted  Picture 
Mode. (except  Expert 1/2)...

Function
19
1.   Press the  MENU button. Then, move to  PICTURE with 
the  ∧, ∨ , ＜ , ＞  buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  Advanced Control 
and press the  ◉OK  button.
3.   
Move to a desired item with the  ∧, ∨  buttons.
4.   
Press the  ＜, ＞  buttons to make a desired adjustment 
and then press the  ◉OK  button.
• You can set image values differently for each input and  Picture Mode.
•   
Execute  Reset for Picture Mode to restore back to default factory...

Function20
Color Temperature●   Set to warm to enhance hotter colors such as red, or set to cool to make picture bluish.
Dynamic Contrast● Adjusts the contrast to keep it at the best level according to the brightness of the screen. 
  The picture is improved by making bright parts brighter and dark parts darker.
Dynamic Color● Adjusts screen colors so that they look livelier, richer and clearer. This feature enhances hue, satu-
ration and luminance so that red, blue, green and white look more vivid.
Film...

Function
21
SCREEN Menu Options
1.   Press the  MENU button. Then, move to  SCREEN with the 
∧ , ∨ , ＜ , ＞  buttons and press the  ◉OK  button.
2.   
Press the  ∧, ∨  buttons to move to  PJT Mode and press 
the  ◉OK  button.
3.   
Move to a desired item with the  ∧, ∨  buttons and then 
press the  ◉OK  button.
•  Select  Rear when projecting from the back of the transparent screen purchased separately.
•   Select  Ceiling when installing the product on the ceiling.
•   When  PJT Mode is  Rear/Ceiling ,...