LG Gr C207 Wtqa Owners Manual

							
2
Entry
Important safety instruction
Identification of parts
Where to install
Door removal
Door replacement
Height adjustment
when the freezer door does not align with the height of the refrigerator door
Starting
Adjusting the temperatures and functions
Refreshment center (Applicable to some models only)
Wine holder
Ice making
Deodorizer(Applicable to some models only)
Egg box
Humidity control in the vegetable compartment
Convert into a vegetable or meat compartment 
(Applicable to some models only)
Location of foods
Storing foods
How to dismantle parts
General information
Cleaning
Trouble shooting
Table of contents
Introduction
Installation
Operation
Suggestion on
food storage
Care and
maintenance
3
3
4
6
7
7
7
8
8
10
11
11
11
12
12
12
13
14
15
16
16
17
5

The working life of this set is 7 years since the date of delivery to consumer.
 
						

							
3
Introduction
Entry
The  model  and  serial  numbers  are  found  on  the  inner  case  or  back  of  refrigerator 
compartment  of  this  unit.  These  numbers  are  unique  to  this  unit  and  notavailable 
to  oth  ers.  You  should  record  requested  information  here  and  retain  this  guide  as  a 
permanent record of your purchase. Staple your receipt here.
Date of purchase                  : Dealer purchased from         :Dealer address                     :Dealer phone no.                  :Model no.                             :Serial no.                              :
Important safety instruction
This  refrigerator  must  be  properly  installed  and  located  in  accordance  with  the 
installation instructions before it is used.
Never  unplug  your  refrigerator  by  pulling  on  the  power  cord.  Always  grip  plug firmly and pull straight out from the outlet.
When  moving  your  appliance  away  from  the  wall,  be  careful  not  to  roll  over  or damage the power cord.
After your refrigerator is in operation, do not touch the cold surfaces in the freezer compartment, particularly when hands are damp or wet. Skin may adhere to these extremely cold surfaces.
Unplug  the  power  cord  from  the  power  plug  for  cleaning  or  other  cares.  Never touch it with wet hands because you can get an electric shock or be hurt.
Never  damage,  process,  severely  bend,  pull  out,  or  twist  power  cord  because power  cord  damage  may  cause  a  fire  or  electric  shock.  You  have  doubts  on whether the appliance is properly grounded.
Never place glass products in the freezer because they may be broken when their inner matters are frozen.
The  appliance  is  not  intended  for  use  by  young  children  or  infirm  persons  without supervision.
Young  childeren  should  be  supervised  to  ensure  that  they  do  not  play  with  the appliance.
Never  allow  anyone  to  climb,  sit,  stand  or  hang  on  the  refreshment  center  door.These  actions  may  damage  the  refrigerator  and  even  tip  it  over,  causing  severe personal injury.
If possible, connect the refrigerator to its own individual electrical outlet to prevent it  and  other  appliances  or  household  lights  from  causing  an  overload  that  could cause a power outage.
The  refrigerator-freezer  should  be  so  positioned  that  the  supply  plug  is  accessible fo rquick disconnection when accident happens.
If  the  supply  cord  is  damaged,  it  must  be  replaced  by  the  manufacturer  or  its service agent or a similarly qualified person in order to avoid a hazard.
Do not modify or extend the Power Cord length.• It will cause electric shock or fire.
Don’t use anextension cord
Accessibility ofSupply Plug
Supply CordReplacement
Warning
 
						

							4
Introduction
DANGER: Risk of child entrapment.
Before you throw away your old refrigerator or freezer:
Take off the doors 
Leave the shelves  in place so that children may not easily c
limb inside.
The  appliance is not intended for use by young children or infirm persons withou t 
supervision.
Y oung children should be supervised to ensure that they do not play with th e 
appliance.
Don’t
  store or use gasoline  or other  flammable vapor and liquids in the vicinity of this 
or any other appliance.
In the event of an electric short circuit, grounding (earthing) r
e duces the risk of electric
shock by providing an escape wire for the electric current. 
In order to prevent possible electric shock, this appliance mu
s t be grounded 
improper use of the grounding plug can result in an electric s hock. Consult a qualified
electrician or service person if the grounding instructions are  not completely
understood, or if you have doubts on whether the appliance  is properly grounded.
Identification of parts 
NOTE
• If you find some parts missing from your unit, they may be parts only used in other
   models.
 
Child entrapment
warning
Don’t store
Grounding (Earthing)
Conversion switch
(Meat/Vegetables) 
 
						

							
5
Installation
 1. Place your appliance where it is easy to 
     use.
 2. Avoid placing the unit near heat sources, 
     direct sunlight or moisture.
 3. To ensure  proper air circulation around the 
     fridge -freezer, please maintain sufficient 
     space on both the sides as well as top 
     and  maintain at least  2 inches (5 cm) from 
     the rear wall.
 4. To avoid vibrations, the appliance must be leveled.
 5. Don't install the appliance below 5℃ . It may cause affect the performance. 
 This appliance contains fluid (refrigerant, lubricant)and is made of parts and 
 materials which are reusable and/or recyclable.
 All the important materials should be sent to the collection center of waste 
 materialand can be reused after rework (recycling). For take back, please contact 
 with thelocal agency. 
Select a good
location
Disposal of the
old appliance
Warning
Remove lower
cover 
Remove the
freezer
compartment
door
Remove the
refrigerator
door        
 Pass the
refrigerator 
Where to install
 
						

							
Installation

6
Door removal
Remove  the  lower  cover  by  lifting  upward.
Pass  the  refrigerator  laterally  through  access
door  as  shown  in  the  right  figure.
Remove lower
cover 
Warning
Remove the
freezer
compartment
door
Remove the
refrigerator
door
Pass the
refrigerator 

1)  Removing  the  hinge  cover  by  loosening  the
screws.  Separate  all  connection  wires  except
for  theearth  line  after.
2) Remove  the  keeper  by  rotating  it  counter
clockwise  (�)and  then  lifting  the  upper
hinge  up (�).
3)  Remove  the  freezer  compartment  door  by
lifting  it  upward. 
1)  Loosen  the  hinge  cover  screws  and  remove
the  cover.  Remove  connection  wire, if  any,
except  for  the  earth  line.
2)  Remove  keeper  by  rotating  it  clockwise  (�)
and  then  remove  the  upper  hinge  by  lifting
it  up  (�).
3)  Remove  the  refrigerator  compartment  door
by  lifting  it  up.
•When  removing  the  upper  hinge,  be  careful  that  the  door  does  not  fall  forwards.
NOTE

Lowercover
Lower  hinge
Keeper

Connectionwires
Hingecover
Upper  hinge
Upper  hinge
Keeper
Upperhinge
Failure  to  do  so  could  result  in  death  or  serious
injury.

If your access door is too narrow for the
refrigerator remove the refrigerator door and
pass the refrigerator laterally. 
Electric Shock Hazard 
Disconnect  electrical  supply  to  refrigerator  before  installing.

6
Installation          
Door removal
Electric Shock Hazard Disconnect electrical supply to refrigerator before installing.
Failure to do so could result in death or serious
injury. 
If your access door is too narrow for the
refrigerator remove the refrigerator door and
pass the refrigerator laterally.
 
Remove the lower cover by lifting upward.
1) Loosen the hinge cover screws and remove
      the cover.
2) Remove the keeper by rotating it to counter
    clockwise (①) and then lifting the upper
    hinge up(②).
NOTE
• When removing the upper hinge, be careful that the door does not fa\
ll forwards.
Installation
6
Door removal
Remove  the  lower  cover  by  lifting  upward.
Pass  the  refrigerator  laterally  through  access
door  as  shown  in  the  right  figure.
Remove lower
cover 
Warning
Remove the
freezer
compartment
door
Remove the
refrigerator
door
Pass the
refrigerator 
1)  Removing  the  hinge  cover  by  loosening  the
screws.  Separate  all  connection  wires  except
for  theearth  line  after.
2) Remove  the  keeper  by  rotating  it  counter
clockwise  (�)and  then  lifting  the  upper
hinge  up (�).
3)  Remove  the  freezer  compartment  door  by
lifting  it  upward. 
1)  Loosen  the  hinge  cover  screws  and  remove
the  cover.  Remove  connection  wire, if  any,
except  for  the  earth  line.
2)  Remove  keeper  by  rotating  it  clockwise  (�)
and  then  remove  the  upper  hinge  by  lifting
it  up  (�).
3)  Remove  the  refrigerator  compartment  door
by  lifting  it  up.
•When  removing  the  upper  hinge,  be  careful  that  the  door  does  not  fall  forwards.
NOTE
Lowercover
Lower  hinge
Keeper
Connectionwires
Hingecover
Upper  hinge
Upper  hinge
Keeper
Upperhinge
Failure  to  do  so  could  result  in  death  or  serious
injury.
If your access door is too narrow for the
refrigerator remove the refrigerator door and
pass the refrigerator laterally. 
Electric Shock Hazard 
Disconnect  electrical  supply  to  refrigerator  before  installing.
3) Remove the freezer compartment door by
    lifting it upward. 
1) Loosen the hinge cover screws and remove
    the cover. Remove connection wire,if any,
    except for the earth line.
2) Remove keeper by rotating it clockwise (①)
    and then remove the upper hinge by 
    lifting it up (②).
3) Remove the refrigerator compartment door by 
    lifting it up.
Pass the refrigerator laterally through access
door as shown in the right figure.
Warning
Remove lower
cover 
Remove the
freezer
compartment
door
Remove the
refrigerator
door        
 Pass the
refrigerator 
 
						

							
7
Installation
Height adjustment
lf the freezer compartment
door is lower than the refrig-
erator compartment door
Level the door by inserting flat(-type)
driver into the groove of the left 
height adjusting screw and rotate it 
clockwise(①).
If the freezer compartment
door is higher than the refrig-
erator compartment door
Level the door by inserting flat(-type)
driver into the groove of the right 
height adjusting screw and rotate it 
clockwise(①).
Door replacement
Mount them in the reverse sequence of removal after they pass through the access door. 
When the freezer door does not align with 
the height of the refrigerator door
Even if the height can not be aligned by using the height
adjustment

screw, insert the transparent sheet supplied with the product.
• Separate the door with the  lower height, use the (+) type screwdriver  to    unscrew the screw at the bottom hinge as shown at Figure①, insert the    transparent sheet between the bottom hinge and the bottom bracket, and then    fix it with the screw as shown at Figure②.
• Insert more transparent sheets enough to align the height. (4 sheets ard supplied    in total.)
The refrigerator doors will close smoothly by heightening the front side by adjusting the height adjusting screw.If the doors do not close correctly,performance maybe
1. Wipe off all dust accumulated during shipping and clean your appliance thoroughly.
2. Install accessories such as the ice cube box, cover evaporating tray, etc., in their    proper places. They are packed together to prevent possible damage during shipping.3. Connect the power supply cord (or plug) to the outlet. Don't double up with other     appliances on the same outlet.
①
②Bottombracket
Transparent sheetBottomhinge
If the height of 
freezer compart-
ment door is 
different from the 
height of Refrig-
erator compart-
ment door
After leveling the
door height
Next
 
						

							
8
Starting
When your refrigerator is first installed, allow it to stabilize at normal operating
temperatures for 2-3 hours prior to filling it with fresh or frozen foods.
If operation is interrupted, wait 5 minutes before restarting.
Adjusting the temperatures and functions
NOTE
• Your model may not include every option.
Operation
 
						

							
9
Operation
Display Power Saving Mode
This function places the display into power saving mode until the next t\
ime the dooris opened.Press the FREEZER and EXPRESS FRZ. buttons simultaneously and hold them \
for 5seconds until the Ding sounds. All LED/LCDs will then turn ON, then OFF.\
 When thepower saving mode is activated, the display will remain off until the ne\
xt time thedoor is opened. Then, it will come on whenever a door is opened or a but\
ton ispressed and remain on for 20 seconds after the last door opening or butt\
on selection.To deactivate the power saving mode, press the FREEZER and EXPRESS FRZ.buttons simultaneously and hold them for 5 seconds until the Ding sounds\
.
You can adjust temperature of and freezer room and refrigerator room.
* Whenever pressing button, setting is repeated in the order of (Middle)\
➔(Middle  
   Strong)➔(Strong)➔(Weak)➔(Middle Weak).
  The actual inner temperature varies depending on the food status, as the\
      indicated setting temperature is a target temperature, not actual \
temperature      within refrigerator.
  Refrigeration function is weak in the initial time. Please adjust temper\
ature        as above after using refrigerator for minimum 2~3 days.
Please select this function for promptfreezer.
 off➔ on➔off is repeated   whenever pressing              button.
 The arrow mark graphic remains at the   "on" when selecting Special Refrigeration "on".
 Prompt freezer function automatically turns off after a fixed time passe\
s.
This button stops operation ofdifferent button.
 Locking or Release is repeated whenever    the            is pressed more than    3 seconds.
 lf you use the           button,    none of the other buttons will work    until you unlock them.
An alarm will sound 3 times when the refrigerator door is left open for more than 1minute. 
This alarm will be rung at an intervals of 30 sec. and stop at the close of the door. If the 
alarm sound does not stop even after the freezer and refrigerator compartment doors are 
closed, contact the service center.
Self-diagnosis function operates when a problem occurs in the unit. When an erroro ccurs 
in the unit. Immediately contact the service center without turning the power OFF. If the 
power is OFF, it will take the engineer longer to find out where the fault occurs.
The pressing of any function buttons will not alter the temperature setting when a fault 
occurs.
How to adjust 
the temperature 
in the freezer 
compartment
How to adjust 
the temperature
 in the 
refrigerator
compartment
Express freezer
(Applicable to 
some models 
only)
Lock
(Applicable to 
some models 
only)
Door open alarm
Self-diagnosis
(fault detection) 
function
 
						

							
10
Operation
How to use
Use the
refreshment
center door as a
stand
Never take out
the inner
refreshment
center cove
Never place
heavy items on
the refreshment
center door or
allow children to
hang it on.
Refreshment center(Applicable to some models only)
Open the refreshment center door.
 You can access the refreshment center
   without opening refrigerator door and thus
   saving electricity.
 Inner lamp is lit in refrigerator compartment
   when the refreshment center door opens.
   Thus it is easy to identify the contents.
 Never use the refreshment center door as a 
   chopping board and take care not to damage 
   it with sharp tools.
 Never rest your arms or severely press on it.
 The refreshment center can not function
   normally without the cover.
 Not only can the refreshment center door 
   may be damaged, but also children may be  
   hurt.