LG Flatron W2443t Users Guide

							20
Troubleshooting
Display image is incorrect
The screen color is
mono or abnormal.
The screen blinks.• Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted in
the slot.
• Set the color setting higher than 24 bits (true color)
at Control Panel - Settings.
• Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Do you see an Unrecognized monitor, Plug&Play (VESA
DDC) monitor found message?
Have you installed the
display driver?• Be sure to install the display driver from the display
driver CD (or diskette) that comes with your
display. Or, you can also download the driver from
our web site: http://www.lge.com.
• Make sure to check if the video card supports
Plug&Play function.
 
						

							21
Specifications                                                          W2443T
23.6 inches (59.9 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 
Visible diagonal size : 59.9cm
0.266 x 0.266 mm (Pixel pitch)
Display
Horizontal Freq. 30 - 83 kHz (Automatic)
Vertical Freq. 56 - 75 Hz (Automatic)
Input Form Separate Sync.
SOG (Sync On Green), DigitalSync Input
Signal Input 15 pin D-Sub Connector
DVI-D Connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo Input
Max VESA 1920 x 1080 @60 Hz
Recommend VESA 1920 x 1080 @60 HzResolution
Plug&Play
On Mode:42 W(Typ.)Sleep Mode≤1 W
Off Mode≤1 WPower
Consumption
Operating Conditions
Temperature 10˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity 5 % to 90 % non-CondensingEnvironment
al Conditions
With Stand
Width    56.77 cm / 22.35 inches 
Height 43.69 cm / 17.20 inches     
Depth 21.20 cm /  8.35 inches
Weight(excl. packing) 5.3 kg (11.89 lbs)Dimensions
& Weight
Tilt : -5˚~15˚Range
AC 100-240V~ 50/60Hz 1.2A Power Input
Attached (     ), Detached ( O )Stand Base 
Wall-outlet typePower cord 
DDC 2B
Without Stand
Width    56.77 cm / 22.35 inches 
Height 36.07 cm / 14.20 inches   
Depth 6.60 cm /  2.60 inches
NOTE
Information in this document is subject to change without notice.
 
						

							22
Specifications                                                          W2443S
23.6 inches (59.9 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 
Visible diagonal size : 59.9cm
0.266 x 0.266 mm (Pixel pitch)
Display
Horizontal Freq. 30 - 83 kHz (Automatic)
Vertical Freq. 56 - 75 Hz (Automatic)
Input Form Separate Sync.
SOG (Sync On Green) Sync Input
Signal Input 15 pin D-Sub Connector
Input Form RGB Analog (0.7 Vp-p/ 75 ohm)Video Input
Max VESA 1920 x 1080 @60 Hz
Recommend VESA 1920 x 1080 @60 HzResolution
Plug&Play
On Mode:42W(Typ.)Sleep Mode≤1 W
Off Mode≤1 WPower
Consumption
Operating Conditions
Temperature 10˚C to 35 ˚C
Humidity 10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity 5 % to 90 % non-CondensingEnvironment
al Conditions
With Stand
Width    56.77 cm / 22.35 inches 
Height 43.69 cm / 17.20 inches     
Depth 21.20 cm /  8.35 inches
Weight(excl. packing) 5.3 kg (11.89 lbs)Dimensions
& Weight
Tilt : -5˚~15˚Range
AC 100-240V~ 50/60Hz 1.2A Power Input
Attached (     ), Detached ( O )Stand Base 
Wall-outlet typePower cord 
DDC 2B
Without Stand
Width    56.77 cm / 22.35 inches 
Height 36.07 cm / 14.20 inches   
Depth 6.60 cm /  2.60 inches
NOTE
Information in this document is subject to change without notice.
 
						

							23
Specifications
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
1
2
3
4
5
6
7
8
9
10
11
*12720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1680 x 1050
1920 x 108031.468
31.469
37.500
37.879
46.875
48.363
60.123
67.500
63.981
79.976
65.290
67.50070
60
75
60
75
60
75
75
60
75
60
60
*Recommend Mode
Indicator
On Mode
Sleep Mode
Off ModeRed
Red Blinking 
Off
LED Color
MODE
 
						

							24
Installing the Wall mount plate
This monitor satisfies the specifications of the  Wall mount plate
or the interchange device.
3.Install the Wall mount plate.
Wall mount plate(Separate purchase)
This is stand-type or wall mount type and is
connectable with Wall mount plate.
Please refer to the installation guide for more details,
which is provided when Wall mount plate is
purchased.
Kensington Security SlotConnected to a locking cable that
can be purchased separately at
most computer stores.
1.Place the monitor face down on the cushion or soft cloth.
2. Loosen the screw which is attached to the stand base, then take off the stand base
from stand body.
Stand Base
Stand BodyScrew
 
						

							Digitally yours