LG Flatron W1943ss Users Guide

Make sure to read the Important Precautionsbefore using the product. 
Keep the Users Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
W1943T
User’s Guide
 

A1
This unit has been engineered and manufactured to ensure your personal safety,
however improper use may result in potential electrical  shock or fire hazards. In
order to allow the proper operation of all safeguards incorporated in this display,
observe the following basic rules for its installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

A2
Important Precautions
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a...

A3
Connecting the Display
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand 
1.Place the monitor with its front facing downward on a soft cloth....

A4
Connecting the Display
Disassembling the stand
1.Put a cushion or soft cloth on a flat
surface.
3.Change your lock on the product as it follows and turn it in the arrow direction.
2.Place the monitor face down on
the cushion or soft cloth.
If you cant release the stand base even the locking rib is at a release position,
Please push the indicated rib down and retry it.
4.Pull out the stand to remove.
 

A5
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range:-5˚~15˚ 
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
 

A6
Connecting the Display
OR
Using the Computer
1.Make sure to turn off the computer and  product. Connect the cable as below sketch map
form to .
12
2.Press        button on the front switch panel to turn the 
power on. When monitor power is turned on, the 
Self Image Setting Function is executed automatically.
(Only Analog Mode)
NOTE‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user
connects the monitor for the first time, this function...

Connecting the Display
A7
Using the cable holder (This feature is not available in all models.)
N
E P O
12
3
E
P ON
4
N O
PECable holder
 

A8
Control Function
Control Panel Functions
MENU ButtonUse this button to enter or exit from the On Screen Display.Use this button to enter 4:3 IN WIDE, PHOTO EFFECT
items, for more information, refer to page A16.
OSD LOCKED/UNLOCKED
This function allows you to lock the current control settings, so
that these settings are not inadvertently changed. To lock the
OSD settings, press and hold the MENU buttonfor several
seconds. The message OSD LOCKED appears.
You can unlock the OSD settings at any time by...

A9
Control Function
Control Panel Functions
This Indicator lights up as red when the display is
operating normally(On Mode). If the display is in
Sleep Mode (Energy Saving), this indicator color
changes to flicker. Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to select an icon in the On Screen
Display.AUTO/SET
Button
AUTO IMAGE ADJUSTMENT
When adjusting your display settings, always press
the AUTO/SETbutton prior to entering the On
Screen Display(OSD). This...