LG Flatron W1930s Users Guide

Make sure to read the Important Precautions before using the product.  
Keep the Users Guide(CD) in an accessible place for future reference.\
See the label attached on the product and give the information to your
dealer when you ask for service.
W1930S
W2230S
User’s Guide
 

A1
This unit has been engineered and manufactured to ensure your personal s\
afety,
however improper use may result in potential electrical  shock or fire h\
azards. In
order to allow the proper operation of all safeguards incorporated in th\
is display,
observe the following basic rules for its installation, use, and servici\
ng.
On Safety
Use only the power cord supplied with the unit. In case you use another \
power
cord, make sure that it is certified by the applicable national standard\
s if not...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do n\
ot place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kit\
chen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow \
the release
of heat generated during operation. If these openings are blocked, built\
-up heat
can cause failures...

Important Precautions
A3
On Cleanin g
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on\
 the display
screen because over-spraying may cause electrical shock.
When cleaning the product, unplug the power cord and scrub gently with a\
 soft cloth to prevent scratching. Do not clean with a wet cloth or spray wate\
r or
other liquids directly onto the product. An electric shock may occur. (\
Do not use
chemicals such as...

A4
Accessories
15-pin D-Sub Signal Cable
(To set it up, this signal cable may
be attached to  this product before shipping out.)
AC-DC adapter
Users Guide/Cards
Power Cord
NOTEThis accessories may look different from those shown here.User must use shielded signal interface cables (D-sub 15 pin cable) wi\
th ferrite cores to
maintain standard compliance for the product.
(Depending on the country)
Power Cord(Depending on the country)
or
!!! Th
ank fo r sele ctin g LGE pr oduc ts !!! 
Please make sure the...

30
10
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range:  10 ˚~30 ˚ 
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the b a c k w a r d  t i l t   angle of the monitor should exceed 10 degrees.
A6A5
Connecting the Display
 

A6
Connecting the Display
Or
Using the Computer
1.Make sure to turn off the computer and  product. Connect the cable as be\
low sketch map
form to .
12
2.Press        button on the front switch panel to turn the power on. When monitor power is turned on, the 
Self Image Setting Function is  executed automatically.
NOTE‘ Self Image Setting Function’?  This function provides the user with optimal display settings.When the u\
ser
connects the monitor for the first time, this function automatically adj\...

A7
Control Panel Functions
Front Panel Controls
Function
Control
MENU ButtonUse this button to enter or exit from the On Screen Display.
 
OSD LOCKED/UNLOCKED
This function allows you to lock the current control settings, so
that these settings are not inadvertently changed. To lock the
OSD settings, press and hold the MENU button for several
seconds. The message OSD LOCKED  appears.
You can unlock the OSD settings at any time by
pushing the MENU button for several seconds. The
message OSD UNLOCKED...

A8
Control Panel Functions
FunctionControl
This Indicator lights up as white when the display 
is operating normally(On Mode). If the display is in
Sleep Mode (Energy Saving), this indicator color
changes to flicker. 
Use this button to turn the display on or off.
Power Button
Power Indicator
Use this button to select an icon in the On Screen 
Display.AUTO/SET 
Button
AUTO IMAGE ADJUSTMENT 
When adjusting your display settings, always press
the AUTO/SET button prior to entering the On
Screen...

On Screen Display (OSD) Control Adjustment
Scr een A dju st m ent
Making adjustments to the image size, position and operating parameters \
of 
the display is quick and easy with the On Screen Display Control system. 
A short example is given below to familiarize you with the use of the co\
ntrols.
The following section is an outline of the available adjustments and sel\
ections
you can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the  MENU Button,  then the...