LG Flatron M2380d Owners Manual

							11
PREPARATION
DETACHING STAND
 ■The image shown may be somewhat different from your set.
1
2
3
Place  the  set  screen  side  down  on  a  cushion 
or soft cloth.
Detach the monitor to the  Stand Base by turn-
ing the screw to the left.
Turn the screw by using a  Coin.
Pull the stand base.
M2080D/M2280D/M2380D/M2780D
Stand Base
Coin
   
						

							12
PREPARATION
PREPARATION
DETACHING STAND
 ■The image shown may be somewhat different from your set.
1
2
3
Place  the  set  screen  side  down  on  a  cushion 
or soft cloth.
Pull the stand base.
M2080DF/M2280DF/M2380DF/M2780DF
Detach the monitor to the Stand Base by turn-
ing the screw to the left.
Turn the screw by using a  Coin.
Stand Base
Coin
 
						

							13
PREPARATION
DETACHING STAND
 ■The image shown may be somewhat different from your set.
1
2
3
Place  the  set  screen  side  down  on  a  cushion 
or soft cloth.
Pull the stand base.
M2080DB/M2280DB/M2380DB
Detach the monitor to the Stand Base by turn-
ing the screw to the left.
Turn the screw by using a  Coin.
Stand Base
Coin
   
						

							14
PREPARATION
PREPARATION
DETACHING STAND BODY
 ■ The image shown may be somewhat different from your set.
 ■ Remove the Stand Body in the same way as the following when using it as a Wall Hook.
1. Remove the screw 2 point.
2. Pull the stand body.
3. Assemble the screw 2 point
Screw
M2080D / M2280D
M2380D / M2780D M2080DB / M2280DB
M2380DB
 
						

							15
PREPARATION
WALL MOUNT : HORIZONTAL INSTALLATION
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation
instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop.1. Be sure to use screws and a wall mount that meet VESA standards.
2. Using screws longer than those recommended might damage the product.
3. Using screws that do not meet VESA standards might either damage the product or result in it coming  away from the wall. We will not be held responsible for any damage resulting from failure to follow these 
instructions.
4. VESA compatible only with respect to screw mounting interface dimensions and mounting screw speci -
fications
5. Please use VESA standard as below.
      5-1) 784.8 mm (30.9 inch) and under   
            * Wall Mount Pad Thickness : 2.6 mm
            * Screw : Φ 4.0 mm x Pitch 0.7 mm x Length 10 mm
      5-2) 787.4 mm (31.0 inch) and above 
            * Please use VESA standard wall mount pad and screws. 
10 cm
10 cm
10 cm
10 cm
10 cm
Wall Mount Pad < Screw Mounting Interface Dimensions >
ModelM2080D 
M2280D
M2380D 
M2080DF
M2380DF
M2380DF M2080DB
M2280DB
M2380DB
M2080DN
M2380DN
M2380DN M2780D
M2780DF
M2780DN
VESA ( A x B)
75 x 75 200 x 100
Wall mount 
bracket(optional) RW120
RW240
   
						

							16
PREPARATION
PREPARATION
DESKTOP PEDESTAL INSTALLATION
For proper ventilation, allow a clearance of 10 cm on each side and from the wall.
 ■The image shown may be somewhat different from your set.
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
M2080D / M2280D
M2380D / M2780D
M2080DF / M2280DF
M2380DF / M2780DF
M2080DB / M2280DB
M2380DB
 
						

							17
PREPARATION
POSITIONING YOUR DISPLAY
SWIVEL STAND(Only M2780D / M2780DF)LOCATION
 ■ The image shown may be somewhat different from your set. Adjust the position of the panel in various ways for maximum 
comfort.
 ■ The image shown may be somewhat different from your set. * Tilt range
-5°
10°
 ■ When adjusting the angle of the screen, 
do not put your finger(s) in between the 
head of the monitor and the stand body 
or woofer. 
    You can hurt your finger(s).
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken  not to 
expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a 
position to allow a free flow of air. Do not cover the ventilation openings on the back cover. After installing the set, you can adjust the set manually to the 
left or right direction by 179 degrees to suit your viewing posi-
tion.
WARNING
M2080DF / M2280DF / M2380DF / M2780DF
 
						

							18
PREPARATION
PREPARATION
KENSINGTON SECURITY SYSTEM
- The product is equipped with a Kensington Security System connector on the back panel. Connect the 
Kensington Security System cable as shown below.
- For detailed installation and use of the Kensington Security System, refer to the user’s guide provided  with the Kensington Security System.
For further information, contact http://www.kensington.com, the internet homepage of the Kensington 
company.  Kensington  sells  security  systems  for  expensive  electronic  equipment  such  as  notebook 
PCs and LCD projectors.
NOTE
- The Kensington Security System is an optional accessory.
NOTES
a. If the product feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with product.
b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor’s performance.
c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
M2080D / M2280D
M2380D / M2780D
M2080DN / M2280DN
M2380DN / M2780DN
M2080DF / M2280DF
M2380DF / M2780DF
M2080DB / M2280DB
M2380DB
 
						

							19
EXTERNAL  EQUIPMENT  SETUP
ANTENNA CONNECTION
 ■To prevent damage do not connect to the mains outlet until all connections are made between the devices.
 ■For optimum picture quality, adjust antenna direction.
 ■An antenna cable and converter are not supplied.
Multi-family Dwellings / Apartments
(Connect to wall antenna socket)
Wall
Antenna
Socket
Outdoor
Antenna
Single-family Dwellings / Houses
(Connect to wall jack for outdoor antenna) RF Coaxial Wire (75 Ω)
 ■
In poor signal areas, to get better picture quality, install a signal amplifier to the antenna as shown above.
 ■If signal needs to be split for two sets, use an antenna signal splitter for connection.
EXTERNAL EQUIPMENT SETUP
AntennaSignal
Amplifier
UHF
VHF
   
						

							20
EXTERNAL EQUIPMENT SETUP
EXTERNAL  EQUIPMENT  SETUP
HD RECEIVER SETUP
Connecting with a component cable
 ■To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
 ■The image shown may be somewhat different from your set.
 ► HDMI  Audio Supported format :  Dolby Digital, PCM 
DTS Audio format is not supported.
Signal Component HDMI
480i / 576i YES No
480p / 576p YES YES
720p / 1080i YES YES
1080p YES
(50 Hz / 60Hz only) YES
(24 Hz / 30 Hz / 50Hz / 60Hz)
Connect the video outputs (Y, PB, PR) of the digital 
set-top box to the  COMPONENT IN VIDEO jacks on 
the SET.
Connect  the  audio  output  of  the  digital  set-top  box 
to the  COMPONENT IN AUDIO jacks on the SET.
Turn on the  digital set-top box.
(Refer  to  the  owner’s  manual  for  the  digital  set-top 
box.)
Select  COMPONENT  input  source  using  the  INPUT 
button on the remote control1
2
3
412