LG Flatron L1982u Users Guide

Make sure to read the Important Precautionsbefore using this product. 
Keep the Users Guide (CD) in an accessible place for future reference.
See the attached label on the unit and show this information to your dealer
when  asking for service.
L1982U
User’s Guide
 

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential electrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place the
display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release of
heat generated during operation. If these openings are blocked, built-up heat can
cause failures which...

Connecting the Display
A3
This illustration depicts the typical connection procedure. Your monitor may
differ from the one displayed in the pictures above.
Do not touch or apply force to the monitors screen while expanding or
folding the stand base.
Do not hold the stand base as
shown in this picture.
1.Put your monitor on a table. 
4.Place the monitor upright and adjust the
stand base to the desired angle. Adjust the
stand bases angle by holding the edges of
the monitor gently with both hands.
2.Hold...

A4
Connecting the Display
1.Face the front of the monitor dislpay. Than gently push the monitor backwards,
following the sequence shown in the picture below. 
Folding the stand base
Tilt range 
1.Make sure that the angle of the panel is set for your comfort. 
NOTE  
When the panel is tilted at more than 30˚, you cannot adjust the height of the monitor. 
 

NOTE  
When the monitor is at maximum height, it may slide down slightly due to the
elasticity of the spring. 
Connecting the Display
A5
To adjust the height, 
 Height Range : maximum 2.36 inches (60 mm)
60mm
 

A6
DC-IN D-SUB DVI-D
1
2
PC
PC
3
Connecting the Display
Connecting with the PC
1.Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
2.Connect the signal cable . After it is attached, tighten the thumbscrews to secure the 
connection.
3.Connect the power cable ➂to the AC-DC adapter (AC-DC power supply) , and then
plug the cable into the outlet.
Wall-outlet type
Mac adapterFor Apple Macintosh use, a  separate plug
adapter...

A7
Using the Auto Pivot and Auto Mirror functions
Notice
The Forte Manager software requires Microsoft Explorer 6.0 or later.
When the Auto Mirror function is engaged, the direction of the OSD
(On Screen Display) menu will not  change if it is rotated by 180°. (See the figure below)
The response time (speed) for the Auto Pivot and Auto Mirror functions may vary 
depending on the video card and the PCs performance, None of these functions is 
supported in  DOS mode.
Update the video card driver on your PC...

A8
Using the Auto Pivot and Auto Mirror functions
Auto Mirror
Screen switch : The monitor screen is automatically reversed when you switch it
forward/backward as shown in the figure.
Tip
If you activate the Auto Pivot or the Auto Mirror function while the screen is
almost level, the screen may not work properly.
In this case, set the screen upright and adjust it to the proper angle.
It is recommended that in order to maintain an ergonomic and comfortable 
viewing position, the forward tilt angle of the...

A9
Control Panel Functions
MENU ButtonUse this button to enter or exit from the On Screen Display.
Control Function
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that these settings are not inadvertently
changed. To lock the OSD settings, press and hold the
MENU buttonfor several seconds. The message OSD
LOCKEDappears.
You can unlock the OSD settings at any time by pushing
the MENU buttonfor several seconds. The message
OSD UNLOCKEDappears.
-  + ButtonsUse these...