LG Flatron L1719s Users Guide

							Make sure to read the Important Precautionsbefore using the product. 
Keep the Users Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
L1719S/L1719SP
L1919S/L1919SP
User’s Guide
  
						

							A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential eletrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your service
technician for replacement.
Do not Open the Display:
There are no user serviceable components inside. 
There are Dangerous High Voltages inside, even when the power is OFF. 
Contact your dealer if the display is not operating properly.
To Avoid Personal Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
To Prevent Fire or Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the displays cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
Important Precautions
  
						

							A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance. 
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
  
						

							Connecting the Display
A3
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand 
1. Place the monitor with its front facing downward on a soft cloth.
2.Assemble the Stand Body into the product in the correct direction as shown in the picture.
Make sure you push it until you hear it “click”. 
3.Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.
4.Once assembled take the monitor up carefully and face the front side
REAR
REARR
EA
R
R
E
A
R
F
R
O
N
T
F
R
O
NT
Stand BodyStand Base
Stand Body
  
						

							A4
Connecting the Display
1.Put a cushion or soft cloth on a flat surface.
To remove the Stand: 
2. Place the monitor face down on
the cushion or soft cloth.     
3.Hold the product as it follows and lift up the Stand slightly.
4.Change your hold on the product as it follows and turn the Stand Base in the arrow
direction until you hear a click.
5.Pull out the Stand to remove.
The Head part
The Stand 
base part
  
						

							Connecting the Display
A5
To remove the Stand Base: 
2.
Hold the body of the Stand as it follows.
Type. A
3.Press the four latches individually
toward each end as shown. 
5.The body of the Stand and the Stand
Base are successfully separated.4.Pull up the body of the Stand while
holding the Stand Base with the other
hand. 
1.Ensure there are four latches at the
bottom of the Stand Base.
  
						

							A6
Connecting the Display
To remove the Stand Base: 
2.
Hold the body of the Stand as it follows.
Type. B
3.Press the two latches individually toward each end as shown
1.Ensure there are two latches at the
bottom of the Stand Base.
5.The body of the Stand and the
Stand Base are successfully
separated.4.Pull up the body of the Stand while
holding the Stand Base with the other
hand. 
  
						

							A7
Connecting the Display
20
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚                            
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
When adjusting the angle of the screen, do not
put your finger(s) in between the head of the
monitor and the stand body. You can hurt your
finger(s).Warning:
  
						

							A8
2
1
Connecting the Display
Using the Computer
1.Place the monitor in a convenient, well-ventilated location near your computer. 2.Connect the signal cable. When attached, tighten the thumbscrews to secure the 
connection.
3.Connect the power cord into a proper power outlet  that is easily accessible and close to
the display.
Wall-outlet type
PC-outlet type
MAC
Power CordSignal Cable
Varies according to model.
1
2
Mac adapterFor Apple Macintosh use, a  separate plug adapter is needed to change
the 15 pin high density (3 row) D-sub VGA connector on the supplied
cable to a 15 pin  2 row connector.
4.Press        button on the side switch panel to turn the power on.
When monitor power is turned on, the Self Image Setting
Functionis executed automatically.
(Only Analog Mode)
NOTE‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user
connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual
input signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push
the ‘AUTO/SET’ button on the side panel of the monitor. Otherwise, you may execute the ‘ Factory reset’ option on
the OSD adjustment menu. However, be aware that this option initializes all the menu items except ‘Language’.
NOTE  This is a simplified representation
of the rear view.
This rear view represents a
general model; your display may
differ from the view as shown.
PC
  
						

							A9
Control Panel Functions
MENU ButtonUse this button to enter or exit the On Screen Display.
Control Function
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU buttonfor several seconds.
The message OSD LOCKEDshould appear.
You can unlock the OSD controls at any time by pushing
the MENU buttonfor several seconds. The message
OSD UNLOCKEDshould appear.
ButtonsUse these buttons to select or adjust functions in the On
Screen Display.
For more information, refer to page A16.
Front Panel ControlsSide