LG Flatron L1719s Users Guide

Make sure to read the Important Precautionsbefore using the product. 
Keep the Users Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
L1719S/L1719SP
L1919S/L1919SP
User’s Guide
  

A1
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential eletrical  shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided...

A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which...

Connecting the Display
A3
Important
This illustration depicts the general model of connection. Your monitor may differ from
the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off.
Connecting the stand 
1. Place the monitor with its front facing downward on a soft cloth....

A4
Connecting the Display
1.Put a cushion or soft cloth on a flat surface.
To remove the Stand: 
2. Place the monitor face down on
the cushion or soft cloth.     
3.Hold the product as it follows and lift up the Stand slightly.
4.Change your hold on the product as it follows and turn the Stand Base in the arrow
direction until you hear a click.
5.Pull out the Stand to remove.
The Head part
The Stand 
base part
  

Connecting the Display
A5
To remove the Stand Base: 
2.
Hold the body of the Stand as it follows.
Type. A
3.Press the four latches individually
toward each end as shown. 
5.The body of the Stand and the Stand
Base are successfully separated.4.Pull up the body of the Stand while
holding the Stand Base with the other
hand. 
1.Ensure there are four latches at the
bottom of the Stand Base.
  

A6
Connecting the Display
To remove the Stand Base: 
2.
Hold the body of the Stand as it follows.
Type. B
3.Press the two latches individually toward each end as shown
1.Ensure there are two latches at the
bottom of the Stand Base.
5.The body of the Stand and the
Stand Base are successfully
separated.4.Pull up the body of the Stand while
holding the Stand Base with the other
hand. 
  

A7
Connecting the Display
20
Before setting up the monitor, ensure that the power to the monitor, the computer
system, and other attached devices is turned off. 
Positioning your display
1.Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚                            
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.
When adjusting the angle of the...

A8
2
1
Connecting the Display
Using the Computer
1.Place the monitor in a convenient, well-ventilated location near your computer. 2.Connect the signal cable. When attached, tighten the thumbscrews to secure the 
connection.
3.Connect the power cord into a proper power outlet  that is easily accessible and close to
the display.
Wall-outlet type
PC-outlet type
MAC
Power CordSignal Cable
Varies according to model.
1
2
Mac adapterFor Apple Macintosh use, a  separate plug adapter is needed to change
the 15...

A9
Control Panel Functions
MENU ButtonUse this button to enter or exit the On Screen Display.
Control Function
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU buttonfor several seconds.
The message OSD LOCKEDshould appear.
You can unlock the OSD controls at any time by pushing
the MENU buttonfor several seconds. The message
OSD UNLOCKEDshould appear.
ButtonsUse these buttons to select or adjust...