LG Dh6520t Owners Manual

							Connecting21
Connecting2
USB Connection
Connect	the	USB	port	of	USB	Memory	(or	MP3	player,	etc.)	to	the	USB	port	on	the	front	of	the	unit.
Removing	the	USB	Device	from	the	unit1.	 Choose	a	different	function	mode	or	press	\b	STOP	twice	in	a	row.2.		Remove	the	USB	device	from	the	unit.
Compatib\be USB Devices
	yMP3	Player	:	Flash	type	MP3	player.
	yUSB	Flash	Drive	:		
Devices	that 	support 	USB2.0 	or	USB1.1.	
	yThe	USB	function	of	this	unit	does	not	support	some	USB	devices.
USB device requirement
	yDevices	which	require	additional	program	installation	connected	to	a	computer,	are	not	supported.
	yDo 	not 	extract 	the 	USB 	device 	while 	in 	operation.
	yFor	a	large	capacity	USB,	it	may	take	longer	than	a	few	minute	to	be	searched.
	yTo	prevent	data	loss,	back	up	all	data.
	yIf	you	use	a	USB	extension	cable	or	USB	hub,	the	USB	device	is	not	recognized.
	yUsing	NTFS	file	system	is	not	supported.	(Only	FAT(16/32)	file	system	is	supported.)
	yThis	unit	is	not	supported	when	the	total	number	of	files	is	1	000	or	more.
	yExternal	\fDD,	Card	readers,	\bocked	devices,		or	hard	type	usb	devices	are	not	supported.
	yUSB	port	of	the	unit	cannot	be	connected	to	PC.	The	unit	can	not	be	used	as	a	storage	device.
DH6520T-F0_BAUSLLK_ENG_6191.indd   212012-02-28   �� 4:24:30 
						

							Connecting22
Connecting2
OPTICAL In connection
Connect	an	optical	output	of	Unit	(or	Digital	Device	etc)	to	the	OPTICA\b	IN	connector.
To \fhe \bigi\fal 
op\fical ou\fpu\f jack \g
of your componen\f
Home t\feater speaker ez 
setup
\bisten	to	sound	from	TV,	DVD	and	Digital	Device	with	5.1(2.1	or	2)ch	mode.	Even	in	power	off	mode,	if	you	press	OPTICAL,	then	power	is	on	and	automatically	changed	to	AUX	OPT	mode.
1.	 Connect	the	unit’s	OPTICA\b	IN	jack	to	jack	on	optical	out	of	your	TV	(or	Digital	Device	etc.).
2.	 Select	the	AUX	OPT	by	using	the	OPTICAL.To	select	the	AUX	OPT	directly.
3.	 \bisten	sound	with	5.1(2.1	or	2)ch	speaker.
4.	 To	escape 	from 	AUX 	OPT 	by 	using 	the 	OPTICAL.Function	is	retuned	to	previous	one.
DH6520T-F0_BAUSLLK_ENG_6191.indd   222012-02-28   �� 4:24:30 
						

							Connecting23
Connecting2
Antenna Connection
Connect	the	supplied	FM	antenna	for	listening	to	the	radio.
Connect	the	FM	Wire	antenna	to	the	FM	antenna	connector.
Be	sure	to	fully	extend	the	FM	wire	antenna.	
After	connecting	the	FM	wire	antenna,	keep	it	
as	horizontal	as	possible.,
,Note
DH6520T-F0_BAUSLLK_ENG_6191.indd   232012-02-28   �� 4:24:31 
						

							3	 System	Setting
System Setting2\b
System Setting3
Adjust t\fe setup 
settings
By	using	the	Setup	menu,	you	can	make	various	adjustments	to	items	such	as	picture	and	sound.
You	can	also	set	a	language	for	the	subtitles	and	the	Setup 	menu, 	among 	other 	things. 	For 	details 	on	each	Setup	menu	item,	see	pages	24	to	28.
OSD Initia\b \banguage\p settings 
- Optiona\b
During	the	first	use	of	this	unit,	the	initial	language	setup	menu	appears	on	your	 TV	screen.	You	must	complete	initial	language	selection	before	using	the	unit.	English	will	be	selected	as	the	initial	language.
1.	 Press	1	(POWER)	to	turn	the	unit	on.	 The	language	setup 	menu 	will 	appear 	on 	the 	screen.
2.	 Use	WS\fD	to	select	a	language	then	press	b	ENTER.	The	confirm	menu	will	appear.
3.	 Use	\fD	to	select	the	[Enter]	then	press	b	ENTER	to	finish	the	language	setup.
To disp\bay and exit \pt\fe Setup 
menu
1.	 Press	n	HOME.Displays	the	[\fome	Menu].
2.	 Select	an	[Setup]	by	using	\fD.
3.	 Press	b	ENTER.Displays	the	[Setup].
4.	 Press	n	HOME	or	x	RETURN	to	exit	in	the	[Setup]	Menu.
Abou\f help menu for Se\fup
MenuBu\f\fons Opera\fion
ws
MoveWSMoving	to	another	menu.
aMove\fMoving	to	previous	level.
d
MoveDMoving	to	next	level	or	selecting	menu.
x
Closex RETURNTo	exit	the	[Setup]	menu	or	[	5.1	Speaker	Setup].
b Selec\fb	ENTERTo	confirm	menu.
DH6520T-F0_BAUSLLK_ENG_6191.indd   242012-02-28   �� 4:24:31 
						

							System Setting25
System Setting3
Language
Menu Language
Select	a	language	for	the	Setup	menu	and	then	on	screen	display.
Disc Audio / Disc Subtit\be / Disc 
Menu
Select	the	language	you	prefer	for	the	audio	track	(disc	audio),	subtitles,	and	the	disc	menu.
[Original]
Refers	to	the	original	language	in	which	the	disc	was	recorded.
[O\fher]
To	select	another	language,	press	numeric	buttons	and	then	b	ENTER	to	enter	the	corresponding	4-digit	number	according	to	the	language	code	list	on	the	page	41.	If	you	enter	the	wrong	language	code,	press	CLEAR.
[Off (for Disc Sub\fi\fle)]
Turn	off	Subtitle.
Disp\bay
TV Aspect
Select	which	screen	aspect	to	use	based	on	the	shape	of	your	TV	screen.	
[4:3]
Select	when	a	standard	4:3	 TV	is	connected.
[16:9]
Select	when	a	16:9	wide	TV	is	connected.
Disp\bay Mode
The	Display	Mode	setting	works	only	when	the	 TV	Aspect	mode	is	set	to	4:3.
[Le\f\ferbox]
Displays	a	wide	picture	with	bands	on	the	upper	and	lower	portions	of	the	screen.
[Panscan]
Automatically	displays	the	wide	picture	on	the	entire	screen	and	cuts	off	the	portions	that	do	not	fit.	(If	the	disc/file	is	not	compatible	with	Pan	Scan,	the	picture	is	displayed	at	\betterbox	ratio.)
Reso\bution
Sets	the	output	resolution	of	the	Component	and	\fDMI	video	signal.	Refer	to	“Resolution	Setting”	for	details	about	the	resolution	(page	19).
[Au\fo]
If	the	\fDMI	OUT	jack	is	connected	to	TVs	providing	display	information	(EDID),	automatically	selects	the	resolution	best	suited	to	the	connected	TV.	If	the	COMPONENT	VIDEO	OUT	is	only	connected,	this	changes	the	resolution	to 	480i 	(or 	576i) 	as 	default 	resolution.
[1080p]
Outputs	1	080	lines	of	progressive	video.
[1080i]
Outputs	1	080	lines	of	interlaced	video.
[720p]
Outputs	720	lines	of	progressive	video.
[480p (or 576p)]
Outputs	480	(or	576)	lines	of	progressive	video.
[480i (or 576i)]
Outputs	480	(or	(576)	lines	of	interlaced	video.
DH6520T-F0_BAUSLLK_ENG_6191.indd   252012-02-28   �� 4:24:31 
						

							System Setting26
System Setting3
Audio
5.1 Speaker Setup
Make	the	following	settings	for	the	built-in	5.1	channel	surround	decoder.
1.	 Select	[5.1	Speaker	Setup]	on	the	[Audio]	menu.
2.	 Press	b	ENTER.The	[5.1	SPEAKER]	appears.
3.	 Use	\fD	to	select	the	desired	speaker.
4.	 Adjust	options	using	WS\fD	buttons.
5.	 Returns	to	the	previous	menu	by	pressing	x	RETURN.
[Speaker]
Select	a	speaker	that	you	want	to	adjust.
Certain	speaker	settings	are	prohibited	by	the	
Dolby	Digital	licensing	agreement.,
,Note
[Size]
Since	the	speaker	settings	are	fixed,	you	cannot	change	the	settings.
[Volume]
Adjust	the	output	level	of	each	speaker.		
[Dis\fance]
Adjust	the	distance	between	each	speaker	and	the	listening	position.		
[Tes\f]
Select	[Speaker	 Test	Start]	by	using	the	WS	and	press	b	ENTER.	Press	b	ENTER	again	to	stop.	Adjust	the	volume	to	match	the	volume	of	test	signals	memorized	in	the	system.
DH6520T-F0_BAUSLLK_ENG_6191.indd   262012-02-28   �� 4:24:31 
						

							System Setting27
System Setting3
DRC (Dynamic Range Contro\b) 
Make	the	sound	clear	when	the	volume	is	turned	down	(Dolby	Digital	only).	Set	to	[On]	for	this	effect.
Voca\b
Select	[On]	to	mix	karaoke	channels	into	normal	stereo.
This	function	is	effective	for	multi-channel	karaoke	DVDs	only.
HD AV Sync
Sometimes	Digital	TV	encounters	a	delay	between		picture	and	sound.	If	this	happens	you	can	compensate	by	setting	a	delay	on	the	sound	so	that	it	effectively	‘waits’	for	the	picture	to	arrive:	this	is	called	\fD	AV	Sync.	Use	WS	(on	the	remote	control)	to	scroll	up	and	down	through	the	delay	amount,	which	you	can	set	at	anything	between	0	and	300m	sec.
Lock (Parenta\b Contro\b)
Initia\b Setting t\fe Area Code:
When	you	use	this	unit	for	the	first	time,	you	have	to	set	the	Area	Code.
1.	 Select	the	[\bock]	menu	and	then	press	D.
2.	 Press	D.To	access 	the	[\bock]	options,	you	must 	input	the	password	you	have	created.	Input	a	password	and	press	b	ENTER.	Enter	it	again	and	press	b	ENTER	to	verify.	If	you	make	a	mistake	before	pressing	b	ENTER,	press	CLEAR.
3.	 Select	the	first	character	using	WS	buttons.
4.	 Press	b	ENTER	and 	select 	the 	second 	character	using	WS	buttons.
5.	 Press	b	ENTER	to	confirm	your	Area	code	selection.
Rating
Blocks	playback	of	rated	DVDs	based	on	their	contents.	Not	all	discs	are	rated.
1.	 Select	[Rating]	on	the	[\bock]	menu	then	press	D.
2.	 Input	a	password	and	press	b	ENTER.
3.	 Select	a	rating	from	1	to	8	using	the	WS	buttons.
[Ra\fing 1-8]
Rating	one	(1)	has	the	most	restrictions	and	rating	eight	(8)	is	the	least	restrictive.
[Unlock]
If	you	select	unlock,	parental	control	is	not	active	and	the	disc	plays	in	full.
4.	 Press 	b	ENTER	to 	confirm 	your 	rating 	selection.
DH6520T-F0_BAUSLLK_ENG_6191.indd   272012-02-28   �� 4:24:31 
						

							4	 Operating
System Setting28
System Setting3
Password
You	can	enter	or	change	password.
1.	 Select	[Password]	on	the	[\bock]	menu	and	then	press	D.
2.	 Press	b	ENTER.
3.	 Input	a	password	and	press	b	ENTER.
	 To	change	the	password,	press	b	ENTER	when	the	[Change]	option	is	highlighted.	Input	a	password	and	press	b	ENTER.	Enter	it	again	and	press	b	ENTER	to	verify.
4.	 Press	n	HOME	to	exit	the	menu.
If	you	forget	your	password,	you	can	clear	it	
using	the	following	steps:
1.	 Select	the	[Setup]	menu	on	the	[\fome	Menu].
2.	 Input	the	6-digit	number	 “210499”	and	
press	 b	ENTER.	
The	password	is	cleared.,
,Note
Area Code
Enter	the	code	of	the	area	whose	standards	were	used	to	rate	the	DVD	video	disc,	based	on	the	list	on	page	40.
1.	 Select	[Area	Code]	on	the	[\bock]	menu	then	press	D.
2.	 Input	a	password	and	press	b	ENTER.
3.	 Select	the	first	character	using	WS	buttons.
4.	 Press 	b	ENTER	and 	select 	the 	second 	character	using	WS	buttons.
5.	 Press	b	ENTER	to	confirm	your	Area	code	selection.
Ot\fers
DivX VOD
ABOUT	DIVX	 VIDEO:	DivX®	is	a	digital	video	format	created	by	DivX,	\b\bC,	a	subsidiary	of	Rovi	Corporation.	This	is	an	official	DivX	Certified®	device	that	plays	DivX	video.	 Visit	divx.com	for	more	information	and	software	tools	to	convert	your	files	into	DivX	videos.
ABOUT	DIVX	VIDEO-ON-DEMAND:	 This	DivX	Certified®	device 	must 	be 	registered 	in 	order 	to 	play	purchased	DivX	 Video-on-Demand	( VOD)	movies.	To	obtain	your	registration	code,	locate	the	DivX	VOD	section	in	your	device	setup	menu.	Go	to	vod.divx.com	for	more	information	on	how	to	complete	your	registration.
[Regis\fer]
Displays	the	registration	code	of	your	player.
[Deregis\fer]
Deactivate	your	player	and	display	the	deactivation	code.
All	the	downloaded	videos	from	DivX	 VOD	can	
only	be	played	back	on	this	unit.,
,Note
DH6520T-F0_BAUSLLK_ENG_6191.indd   282012-02-28   �� 4:24:31 
						

							Operating29
Oper\fting4
Using t\fe Home Menu
1.	 Press	n	HOME.Displays	the	[\fome	Menu].
2.	 Select	an	option	by	using	\fD.	
3.	 Press	b	ENTER	then	selected	option	menu.
[Music]	–	Displays	[MUSIC]	menu.
[Movie]	–		Start	video	media’s	playback	or	displays	the	[MOVIE]	menu.
[Photo]	–	Displays	[P\fOTO]	menu.
[Setup]	–	Displays	the	[Setup]	menu.
You	can	not	select	the	[Music],	[Movie]	or	
[Photo]	option	when	the	USB	device	is	not	
connected	and	a	disc	is	not	inserted.,
,Note
Basic Operations
1.	 Insert	the	disc	by	using	the	B	OPEN/CLOSE	or	Connect	the	USB	device	to	the	USB	port.
2.	 Press	n	HOME.Displays	the	[\fome	Menu].
3.	 Select	an	option	by	using	\fD.If	you	select	the	[Movie],	[Photo]	or	[Music]	option	when	you	connect	up	to	two	devices,	it	appears	as	belows.	Select	a	media	then	press	b	ENTER.	
4.	 Press	b	ENTER	then	selected	option	menu.
	
y For	the	most	Audio	CD	and	DVD-ROM	discs,	
playback	starts	automatically.
	
y The	unit	plays	only	music	file	contained	in	
the
	USB 	storage 	device 	or 	disc 	automatically.,
,Note
DH6520T-F0_BAUSLLK_ENG_6191.indd   292012-02-28   �� 4:24:31 
						

							30
Oper\fting4
Operating
ToDo \fhis
Stop	Press	\b STOP.
PlaybackPress d PLAY, MONO/STEREO.
PausePress	M PAUSE/STEP.
Frame-by-Frame	playback
Press	M PAUSE/STEP	repeatedly	to	play	title	Frame-by-Frame.	(DVD,	DivX	only)
Skipping	to	the	next/	previous	chapter/	track/	file
During	playback,	press C/,V SKIP	to	go	to	the	next	chapter/	track/	file	or	to	return	to	the	beginning	of	the	current	chapter/	track/	file.
Press	C,SKIP twice	briefly	to	step	back	to	the	previous	chapter/	track/	file.
\bocating	a	point	quickly 	by	playing	a	file	in	fast	forward	or	fast	reverse
During	playback,	press	c/v SCAN	repeatedly	to	select 	the 	required 	scan 	speed.
To	return	to	normal	speed,	press	d PLAY, MONO/STEREO.
Playing	repeatedly	or	randomly
Press 	h REPEAT repeatedly,	and	the	current	title,	chapter	or	track	will	be	played	back	repeatedly	or	randomly.	
-	DVD	:	Chapter/	 Title/	Off
-	DivX	:	Title/	All/	Off
-		Audio 	CD/ 	MP3/ 	WMA 	:	 Track/	All/	Random/	Off
Slowing	down	the	playing	speed
In	the	pause	mode,	press	S\bOW	(c	or	v)	to	select	the	required	speed.	(DVD,	DivX	only)	 The	DivX	file	cannot	be	slow	down	reverse	playback.
Ot\fer Operations
Disp\baying Disc Information 
on-screen
You	can	display	various	information	about	the	disc	loaded	on-screen.
1.	 Press	m	INFO/DISPLAY	to	show	various	playback	information.	The	displayed	items	differ	depending	on	the	disc	type	or	playing	status.
2.	 You	can	select	an	item	by	pressing	WS,and	change	or	select	the	setting	by	pressing	\fD.
Title	–		 Current	title	number/	total	number	of	titles.
Chapter	–		 Current	chapter	number/	total	number	of	chapters.
Time	–	Elapsed	playing	time.
Audio	–		Selected	audio	language	or	channel.
Subtitle	–	Selected	subtitle.
Angle	–		Selected	angle/	total	number	of	angles.
If	any	button	is	not	pressed	for	a	few	seconds,	
the	on-screen	display	disappears.,
,Note
DH6520T-F0_BAUSLLK_ENG_6191.indd   302012-02-28   �� 4:24:31