LG Cf181d Locos Projector User Manual

DownUp
Names of parts
11
* Lamp indicator, operation indicator and temperature indicator at the top of the projector show the user the operating status of the projector.
Operation Indicator
Temperature Indicator
Deco LED
(Lens Shift Dial)
Lamp Indicator
Projector Status Indicators
Operation Indicator
/ Temperature Indicator
Lamp Indicator
Deco LED
(Lens Shift Dial)Red
Green
Orange(flashing)
Green (flashing)
Off
Orange
Red(flashing)
Red
Red(flashing)
Green (flashing)
Blue (flashing)Standby.
Unit is in...

Names of parts
12
Accessories
Optional Extras 
LIGHT
* Contact your dealer to purchase these items.
* The lamp is consumable and needs to be replaced with a new one when it is burned out. Contact your service personnel for replacing of lamp.
* Optional parts can be changed without notice to improve the quality of the product, and new optional parts can be added.Remote Control
Power Cord 
Video Cable
Filter
Owner’s manual
Computer Cable
SCART to RCA jackLamp 
S-Video Cable Projection Screen 
1.5V1.5V
2...

Installing and Composition
13
Installing and Composition
Provide proper ventilation for this projector.
The projector is equipped with ventilationholes(intake)
on the bottom and ventilation holes(exhaust) on the front.
Do not block or place anything near these holes, or internal
heat build-up may occur, causing picture degradation or
damage to the projector.
Place this projector in adequate temperature and humidity conditions.
Install this projector only in a location where adequate temperature and...

Installing and Composition
14
1. Place the projector on a sturdy and horizontal surface.
2. Place the projector the desired distance from the screen. The distance between the projector and the screen deter-
mines the actual size of the image. 
3. Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle, the
screen image will be crooked. The keystone adjustment may correct this (Refer to page 25.).
4. Once you have positioned the...

Installing and Composition
15
This projector has a ‘Kensington’Security System Connector on the side panel. Connect the ‘Kensington’Security
System cable as below.
For the detailed installation and use of the Kensington Security System, refer to the user’s guide included to
the Kensington Security System set. 
And for further information, contact http://www.kensington.com.
 The kensington Security System is an optional item.
Using Kensington Security System 

Installing and Composition
16
* Do not disconnect the power cord while the suction/discharge fan in operation. If the power cord is disconnected during
the suction/ discharge fan in operation, it may takes longer to activate the lamp after turning on the power and the lifespan
of the lamp may be shortened. 
Turning on the Projector
Turning off the Projector
1. Connect power cord correctly.
2. Remove the lens cap. If it is left on, it could become deformed due to the heat produced by the
projection lamp....

Installing and Composition
17
Turning the Lens shift dial with excessive power may cause damage to the projector.
Turn the Lens shift dial left or right to adjust the projector image up or down.
When an image appears on the screen, check if it is in focus and fits the screen well.
To adjust the focus of the image, rotate the focus ring which is the outer ring on the lens.To adjust the size of the image, rotate the zoom ring which is the under ring on the lens.
Focus ring
Zoom ring
Focus and Position...

Connection
18
Connection
Connecting to a Desktop PC
* You can connect the projector to a computer of VGA, SVGA, XGA, SXGA and 1080p/60Hz output. * Refer to page 30 for resolutions the projector supports.
< How to connect >
Connect the RGB IN of the projector and the computer output port
with computer cable.
* You may have to change the resolution that your PC
exports to one supported by the projector. Refer to page 30.
This projector may not support output from laptops when
the laptop screen is on....

Connection
19
Connecting to a DVD
< How to connect >
a.Connect the DVD component cable to the Y, PBand PRof
the COMPONENT IN of the projector.  
* When connecting the component cable, match the jack colors
with the component cable.(Y=green, PB=blue, PR=red)
b. You may use HDMI instead of component if available on the
DVD player. HDMI supports better quality than component. 
PRPBY(R) AUDIO (L) 
* The output jacks (Y, PB, PR) of the DVD might be labeled as Y, Pb, Pr / Y, B-Y, R-Y / Y, Cb, Cr according to...

Function
20
Function
PICTURE Menu Options
* In this manual, the OSD(On Screen Display) may be different from your Projector’s because it is just an example to
help with the Projector operation.
* This operating guide explains operation of RGB(PC) mode mainly.
1. Press the MENUbutton. Then, move to PICTUREwith the ,,,
buttons and press the OK button.
2. Move to a sub-item with the  button. Then, use the 
,buttons to
move to a desired function and press the 
OK button.
3. Use the 
,buttons to make a...