LG 55lw5600 Led Lcd Tv Owners Manual

DivX supported mode
File ExtensionsAudio/VideoCodec    Profile/Level Support  Explanation
.asf.wmv
Video
VC-1 Advanced ProfileAdvanced Profile@Level 3 (e.g. 720p60, 1080i60, 1080p30)Only streams compliant to SMPTE 421M VC-1 standard are supported.VC-1 Simple and Main Profiles
Simple Profile@Medium Level (e.g. CIF, QVGA)Main Profile@High Level (e.g. 1080p30)
AudioWMA Standard
WMA 9 Professional
.divx.avi
Video
DivX3.11
Global motion compensation or quarterpel motion estimation does not supported. Streams...

3D supported formats
InputSignalResolutionHorizontalFrequency (kHz)
Vertical Frequency(Hz)Playable 3D video format
HDMI
720p1280x72045.0060y»Side by Sidey»Top & Bottomy»HDMI 3D Top & Bottom
90.0060y»HDMI 3D Frame Packing
1080i1920x108033.7560y»Side by Sidey»Top & Bottomy»HDMI 3D Side by Side (Half)
1080p1920x1080
67.5060
y»Side by Sidey»Top & Bottomy»Checker Boardy»Single Frame Sequential
27.0024
y»Side by Sidey»Top & Bottomy»Checker Boardy»HDMI 3D Top & Bottom
54.0024y»HDMI 3D Frame Packing
67.50  ( LCD...

Wireless LAN for Broadband/DLNA Adaptor SPEC (For LW9500 series)
This device only works with compatible LG TV.
StandardIEEE802.11a/b/g/n
Frequency Range2402 to 2483 MHz5150 to 5250 MHz5725 to 5850 MHz
ModulationCCK / OFDM / MIMO
Output Power (Typical)
802.11a: 14 dBm802.11b: 17 dBm802.11g: 14 dBm802.11n: 13 dBm
Data rate802.11a/g: 54 Mbps802.11b: 11 Mbps802.11n: 300 Mbps
Antenna Gain (Typical)2402 to 2483 MHz: 1.17 dBi5150 to 5250 MHz: 4.67 dBi5725 to 5850 MHz: 3.30 dBi 
Occupied bandwidth802.11a/b/g:...

IR CODES
(Depending on model)
How to Connect
Connect your wired remote control to the Remote Control port on the TV.
Remote Control IR Codes
Output waveform
Single pulse, modulated with 37.917kHz signal at 455kHz
T1Tc
Frame configuration
1st frame
C0
C1C2C3C4C5C6C7 C0C1C2C3C4C5 C6C7D0D1 D2D3 D4D5 D6D7 D0D1D2D3 D4D5D6D7
 Lead code
Low cu\ftom code H\bgh cu\ftom code Data code Data code 
Repeat frame
Repeat  cod e
Tf
Lead code
4.5 ms
9 ms 
Repeat code
2.25 ms 
9 ms  0.55 ms 
Bit description
0.56 
ms
1.12...

Code (Hexa)FunctionNoteCode (Hexa)FunctionNote
08POWERRemote control Button (Power On/Off)0FTVRemote control Button
DC3DRemote control Button
45Q.MENURemote control Button5BEXITRemote control Button
43HomeRemote control ButtonD6TVDiscrete IR Code(TV Input Selection)0BINPUTRemote control Button
10 - 19Number Key 0-9Remote control ButtonC4POWER ONDiscrete IR Code(Only Power Off)4C- (Dash)/LIST Remote control Button
1AFLASHBKRemote control ButtonC5POWER OFFDiscrete IR Code(Only Power Off)09MUTE/DELETERemote...

EXTERNAL CONTROL DEVICE SETUP
RS\b\f3\fC Setup
Connect the RS-232C (serial port) input jack to 
an external control device (such as a computer or 
an A/V control system) to control the product’s 
functions externally.
Connect the serial port of the control device to the 
RS-232C jack on the product back panel.
 NOTE
yyRS-232C on this TV is intended to be used 
with third party RS-232C control hardware 
and software. The instructions below 
are provided to help with programming 
software or to test...

RS\b\f3\fC configurations
7-Wire Configuration 
(Serial female-female NULL modem cable)
PCTV
RXD
2 3TXD
TXD
3 2RXD
GND
5 5GND
DTR
4 6DSR
DSR
6 4DTR
RTS
7 8CTS
CTS
8 7RTS
D-Sub 9 D-Sub 9
3-Wire Configurations(Not standard)
PC TV
RXD
2 3TXD
TXD
3 2RXD
GND
5 5GND
DTR
4 6DSR
DSR
6 4DTR
RTS
7 8CTS
CTS
8 7RTS
D-Sub 9 D-Sub 9
Set ID
Set ID number.
?ꔀꔉ
•  Language
•  Caption  : Off
•  ISM Method  : Normal
•  Power Indicator 
•  Pointer
•  Smart Share Setting 
•  Initial Setting
•  Set ID  : 1
•  Mode Setting  :...

Command reference list
Communication Parameters
yyBaud rate: 9600 bps (UART)
yyData length: 8 bits
yyParity : None
yyStop bit: 1 bit
yyCommunication code: ASCII code
yyUse a crossed (reverse) cable.
COMMAND1COMMAND2DATA(Hexadecimal)COMMAND1COMMAND2DATA(Hexadecimal)
01. Powerka00 - 0114. Treblekr00 - 64
02. Input Selectxb(See p.130)15. Bassks00 - 64
03. Aspect Ratiokc(See p.130)16. Balancekt00 - 64
04. Screen Mutekd00 - 0117. 3D (For 3D TV)xt(See p.131)
05. Volume Muteke00 - 0118. Color Temperaturexu00 -...

Transmission / Receiving protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the set.(j, k, m or x)
[Command 2] : Second command to control the set.
[Set ID] : You can adjust the set ID to choose desired set ID number in Option menu. Adjustment range is 
1~ 99. When selecting Set ID ‘0’, every connected the set is controlled. Set ID is indicated as decimal (1~ 
99) on menu and as Hexa decimal (0x0~ 0x63) on transmission /receiving protocol.
[DATA] :...

01. Power (Command: k a)To control Power On/Off of the set.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Data 00: Power Off Data 01: Power On
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
* In  a  like  manner,  if  other  functions  transmit  ‘FF’ data  based  on  this  format,  Acknowledgement  data feedback presents status about each function.* Note:  In  this  model,  set  will  send  the  Acknowledge after power on processing completion. There might be a time delay between command and...