LG 50pk760 Owners Manual

							A-37
PREPARATION
FRONT PANEL CONTROLS
 
■ Image shown may differ from your TV.
NOTE
 
► TV can be placed in standby mode in order to reduce the power consumptio\
n. And TV should be 
switched off using the power switch on the TV if it will not be watched for some time, as this will 
reduce energy consumption.
 
The energy consumed during use can be significantly reduced if the level\
 of 
brightness of the picture is reduced, and this will reduce the overall r\
unning cost.
 
 CAUTION
 
► Do not step on the glass stand or subject it to any impact. It may break\
, causing possible injury from frag-
ments of glass, or the TV may fall.
 
►  Do not drag the TV. The floor or the product may be damaged.
PROGRAMME
VOLUME
MENU OK
INPUT
POWER
Intelligent Sensor
Adjusts picture 
according to the sur- rounding conditions. Remote Control Sensor
Power/Standby Indicator
(Can be adjusted using the Power Indicator in 
the  OPTION  menu.)
 
						

							A-38
PREPARATION
PREPARATION
BACK PANEL INFORMATION
 
■ Image shown may differ from your TV.
Power Cord Socket
This TV operates on an AC power. The volt-
age is indicated on the Specifications page. 
(►  p.184 to 200 ) Never attempt to operate 
the 

TV on DC power. 
LAN
Network connection for 
 AccuWeather, 
Picasa, YouTube, etc.
Also used for video, photo and music files on 
a local network. 
OPTICAL DIGITAL AUDIO OUT 
Connect digital audio to various types of 
equipment. 
Connect to a Digital 

Audio Component.
Use an Optical audio cable. 
RGB/DVI Audio Input
Connect the audio from a PC or DTV. 
Euro Scart Socket (AV1) 
  Connect scart socket input or output from an 
external device to these jacks. 
Component Input
Connect a component video/audio device to 
these jacks.
HDMI/DVI IN Input
Connect an HDMI signal to HDMI IN. Or DVI 
(VIDEO) signal to HDMI/DVI port with DVI to 
HDMI cable. RGB IN Input
Connect the output from a PC.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
This port is used for Service or Hotel mode. 
WIRELESS Control
Connect the Wireless Ready Dongle to the 
TV to control the external input devices con-
nected to Wireless Media Box wirelessly

. 
Audio/Video Input
Connect audio/video output from an external 
device to these jacks. 
Antenna Input
Connect antenna or cable to this jack. 
USB Input 
Connect USB storage device to this jack.
PCMCIA (Personal Computer Memory 
Card International 
 Association) Card Slot
Insert the CI Module to PCMCIA
  CARD 
SLOT.
(This feature is not available in all countries.)
Headphone Socket
Plug the headphone into the headphone 
socket.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CAUTION
 
►   Use a product with the 
following thickness for 
optimal connection to 
HDMI cable (Only HDMI 
IN 4) / USB device.
   *A    10 mm
910111278
43256
13
14
7
11
6
15
1
 
						

							A-39
PREPARATION
STAND INSTALLATION
 
■ Image shown may differ from your TV.
When assembling the desk type stand, check 
whether the bolt is fully tightened. (If not tightened 
fully, the product can tilt forward after the product 
installation.) If you tighten the bolt with excessive 
force, the bolt can deviate from abrasion of the 
tightening part of the bolt. 
Assemble the parts of the  Stand Body with 
the  Stand Base of the TV.
At this time, tighten the screws that hold the 
Stand Body on.2
Stand Body
Carefully place the TV screen side down 
on a cushioned surface to protect the 
screen from damage.1
M4 X 20
Stand Base
Assemble the TV as shown.3
Fix the 4 bolts securely using the holes in 
the back of the TV.4
M4 X 12
BACK COVER FOR 
WIRE ARRANGEMENT
 
■ Image shown may differ from your TV.
    After Connecting the cables as necessary,  install  Cable Holder as shown and bundle 
the cables. To connect additional equip-
ment, see the External Equipment Setup  
section.
1
FOR DESK-TYPE STAND 
FOR WALL MOUNT 
      Install the  Cable Management Clip  as 
shown.1
Cable Management Clip
 
     Connect the cables as necessary. To con-
nect additional equipment, see the  External 
Equipment Setup  section.2
Cable Holder
NOTE
 
► Do not use the  Cable Management Clip 
to lift the TV.
-   If the TV is dropped, you may be injured or 
the TV may be damaged.
 
						

							A-40
PREPARATION
PREPARATION 
■ This feature is not available for all models.
 
■ Image shown may differ from your TV.
KENSINGTON SECURITY 
SYSTEMCAREFUL INSTALLATION 
ADVICE 
 
■ You should purchase necessary components 
to fix the TV safety and secure to the wall on 
the market.
 
■    Position the TV close to the wall to avoid the 
possibility of it falling when pushed.
 
■    The instructions shown below are a safer way 
to set up the TV, by fixing it to the wall, avoid-
ing the possibility of it falling forwards if pulled. 
This will prevent the TV from falling forward 
and causing injury. This will also prevent the 
TV from damage. Ensure that children do not 
climb or hang from the TV.
3
Use the eye-bolts or TV brackets/bolts to fix the 
product to the wall as shown in the picture. 
(If your TV has bolts in the eyebolts, loosen then 
bolts.)
* Insert the eye-bolts or TV brackets/bolts and 
tighten them securely in the upper holes.
Secure the wall brackets with the bolts on the 
wall. Match the height of the bracket that is 
mounted on the wall.
Use a sturdy rope to tie the product for align-
ment. It is safer to tie the rope so it becomes 
horizontal between the wall and the product.
2  2 
1
1
  The TV is equipped with a Kensington Security 
System connector on the back panel. Connect 
the Kensington Security System cable as shown 
below.
For the detailed installation and use of the 
Kensington Security System, refer to the user’s 
guide provided with the Kensington Security 
System.
For further information, contact http://www.kens-
ington.com, the internet homepage of the 
Kensington 
company. Kensington sells security systems for 
expensive electronic equipment such as note-
book PCs and LCD projectors.
1
2
3
NOTE
 
► When moving the TV undo the cords first.
 
► Use a platform or cabinet strong and large 
enough to support the size and weight of the TV.
 
► To use the TV safely make sure that the height of 
the bracket on the wall and on the TV is the 
same.
NOTE
 
► The Kensington Security System is an optional 
accessory.
 
► If the TV feels cold to the touch, there may be a 
small “flicker” when it is turned on.
    This is normal
, there is nothing wrong with TV.
 
► Some minute dot defects may be visible on the 
screen, appearing as tiny red, green, or blue 
spots. However, they have no adverse effect on 
the monitors performance.
 
► Avoid touching the LCD screen or holding your 
finger(s) against it for long periods of time.
    Doing so may produce some temporary distortio
n
   effects on the screen.
 
						

							A-41
PREPARATION
SWIVEL STAND 
 
■ Image shown may differ from your TV.
After installing the TV, you can adjust the TV set 
manually to the left or right direction by 20 
degrees to suit your viewing position.
 
■ The TV can be installed in various ways such as 
on a wall, or on a desktop etc.
 
■ The TV is designed to be mounted horizontally.
Power 
Supply
Circuit 
breaker
EARTHING
Ensure that you connect the earth wire to prevent 
possible electric shock. If grounding methods are 
not possible, have a qualified electrician install a 
separate circuit breaker. 
Do not try to earth the TV by connecting it to tele-
phone wires, lightening rods or gas pipes.
WALL MOUNT: HORIZONTAL 
INSTALLATION
 
■ We recommend the use of a LG Brand wall 
mounting bracket when mounting the TV to a wall.
 
■ We recommend that you purchase a wall mount-
ing bracket which supports VESA standard.
 
■ LG recommends that wall mounting be per-
formed by a qualified professional installer.
Model VESA
(A  * B) Standard 
Screw Quantity
42/47LE73 **200 * 200  M6  4 
10 cm
10 cm
10 cm
10 cm
10 cm
NOTE
 
► Should Install wall mount on a solid wall per-
pendicular to the floor.
 
► Should use a special wall mount, if you want 
to install it to ceiling or slanted wall.
 
► The surface that wall mount is to be mount-
ed on should be of sufficient strength to sup-
port the weight of TV set; e.g. concrete, nat-
ural rock, brick and hollow block.
 
► Installing screw type and length depends on 
the wall mount used. Further information, 
refer to the instructions included with the 
mount.
 
► LG is not liable for any accidents or damage 
to property or TV due to incorrect installa-
tion:
 - Where a non-compliant VESA wall mount  is used.
 - Incorrect fastening of screws to surface  which may cause TV to fall and cause per-
sonal injury.
 - Not following the recommended Installation  method.
DESKTOP PEDESTAL 
INSTALLATION
10 cm
For adequate ventilation allow a clearance of 10 
cm all around the TV.
10 cm
10 cm 10 cm
 
■ Image shown may differ from your TV.
 
						

							A-42
PREPARATION
PREPARATION
REMOTE CONTROL KEY FUNCTIONS 
When using the remote control, aim it at the remote control sensor on th\
e TV.
 (POWER)
LIGHT
ENERGY SAVING
AV MODE
       INPUT
TV/RAD Switches the TV on from standby or off to standby.
You can turn the light of the remote control button 
on or of

f. 
Adjust the Energy Saving mode of the TV.( ►
 p.138)
It helps you select and set images and sounds 
when connecting 
 AV devices.(►
 p.66)
External input mode rotate in regular sequence.
(► p.57)
Selects Radio, TV and DTV programme.
Selects a menu.
Clears all on-screen displays and returns to TV 
viewing from any menu.
(► p.31)
Select the desired NetCast menu source.  (► p.68) 
(AccuWeather, Picasa, YouTube and etc.)
NetCast menu source can differ by country.
Select the desired quick menu source. (Aspect 
Ratio, Clear V

oice II , Picture Mode, Sound Mode, 
Audio (or 
Audio Language), Sleep Timer, Skip Off/
On, USB Device).
(► p.30)
Allows you to navigate the on-screen menus and 
adjust the system settings to your preference.
Accepts your selection or displays the current 
mode. 
Allows the user to move return one step in an inter-
active application, EPG or other user interaction 
function.
 
Clears all on-screen displays and returns to TV 
viewing from any menu.
MENU
NetCast
Q. MENU
THUMBSTICK
(Up/Down/Left/Right)
OK 
BACK EXIT
GUIDE
INFO  i AD
APP/ *Shows programme guide
. (► p.129)
Shows the present screen information.
Switches the 
 Audio Description On or Off.
Select the MHP TV menu source. (Only Italy)
(Only  42/47LE7380 )
 
						

							A-43
PREPARATION
1
11
0 to 9 number button
(Space)
LIST
Q.VIEW Selects a programme.
Selects numbered items in a menu.
Opens an empty space on the screen keyboard.
Displays the programme table. (► p.55)
Returns to the previously viewed programme.
]
TELETEXT 
BUTTONS
SUBTITLE These buttons are used for teletext.
For further details, see the ‘T
eletext’ section.
( ►
 p.177)
Recalls your preferred subtitle in digital mode.
See a list of AV devices connected to TV.
When you toggle this button, the Simplink menu 
appears at the screen. (►
 p.62)
Coloured 
buttons These buttons are used for teletext (on 
TELETEXT 
models only),  Programme edit.
@Direct access to your internet portal of entertainment 
and news services developed by Orange
. (Only 
France)
 
						

							A-44
PREPARATION
PREPARATION
Installing Batteries
 
■ Open the battery compartment cover on the back and install 
the batteries matching correct polarity (+with +,-with -). 
 
■ Install two 1.5 V AAA batteries. Do not mix old or used batter-
ies with new ones.
 
■ Close cover

.
 
■ To remove the batteries, perform the installation actions in 
reverse.
SIMPLINK / 
MY MEDIA  Menu    
control buttons Controls SIMPLINK or MY MEDIA menu (Photo List, 
Music List and Movie List).
VOLUME UP
/DOWN
MARK
FAV
CHAR/NUM 
RATIO
DELETE  MUTE
Programme UP/DOWN
PAGE UP/ DOWN Adjusts the volume. 
Select the input to apply the Picture Wizard 
settings.
Check and un-check programmes in the USB 
menu.
Displays the selected favourite programme.
Shifts the Character or Number for NetCast menu. 
Selects your desired Aspect Ratio of picture.
(
►
 p.135)
Deletes the entered character when entering the 
character on the screen keyboard. 
Switches the sound on or off.
Selects a programme.
Move from one full set of screen information to the 
next one.
 
						

							A-45
PREPARATION
PLASMA TV MODELS : 50/60PK5**, 50/60PK7
***, 50/60PK9
*** , 
50/60PX9 *** 
This item is not included for all models.
* 
Lightly wipe any stains or 
fingerprints on the surface 
of the 
TV with the polishing 
cloth.
Do not use excessive force. 
This may cause scratching or 
discolouration.      x 4x 3
M4x28 M5x14
(Only 50PK5 **)
x 4 x 4
M4x28
M4x14
(Only 50PK7 ***, 50PK9
***, 
50PX9 ***)
Bolts for stand assembly
Ferrite Core
(
This item is not 
included for all  models.
)
Ferrite Core
(
This item is not 
included for all  models.
)
Ferrite core can be used to 
reduce the electromagnetic 
wave when connecting the 
power plug .
The closer the location of the 
ferrite core to the power plug, 
the better it is.
Install the power 
plug closely.
Ferrite core can be used to 
reduce the electromagnetic wave 
when connecting the LAN cable.
Place the ferrite core far from 
TV and wind the LAN cable in 
the ferrite core once.
Cable Holder
x 2
Cable 
Management Clip
(Only 50/60PK7 ***, 
50/60PK9 ***, 
50/60PX9 ***)
Wireless LAN for
Broadband 
/DLNA Adaptor
(Only 50/60PK950, 
50/60PK950N, 50/60PK980, 
50/60PK990
, 50/60PX950N, 
50/60PX980, 50/60PX990 )
ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please 
contact the dealer where you purchased the TV.
 
■  Image shown may differ from your TV.
Owner’s Manual
Remote Control Batteries (AAA)
Power CordNero MediaHome  4 Essentials CD
AV  M O D ELIGHTINPUTENERGY
 SAVING
1.,;@2 abc3 def4 ghi5 jkl6 mno7pqrs8 tuv0[9 wxyz
BACK EXIT
OK
LISTQ.VIEW
MENUQ.MENU
GUIDE
ADAPP/
*
FREEZE
INFO
P
A
G
EFAVRATIOMUTE
MARK
DELETECHAR/NUMP
TV/
RAD
(Except for 50/60PK9 ***, 
50/60PX9 ***)
AV  M O D ELIGHTINPUTENERGY
 SAVING
1.,;@2 abc3 def4 ghi5 jkl6 mno7pqrs8 tuv0[9 wxyz
BACK EXIT
OK
LISTQ.VIEW
MENUQ.MENU
GUIDE
ADAPP/
*
FREEZE
INFO
P
A
G
EFAVRATIOMUTE
MARK
DELETECHAR/NUMP
TV/
RAD
(Only 50/60PK9 ***, 
50/60PX9 ***)
x 2
Slightly wipe stained spot on the exterior only with the 
cleansing cloths(mitt) for the product exterior if there is  stain or fingerprint on surface of the exterior.
For cleaning front frame, please slowly wipe in one direction after spraying water 1~2 times on cleansing cloths. Please  remove excessive moisture after cleaning.
Excessive moisture may cause water stains on the frame.
(Only 50/60PX9
***)
cleansing cloths(mitt)
Protection 
Cover
3D Glasses 
(Only 50/60PX9 ***)
Polishing Cloth
Polishing cloth for 
use on the screen.
 
						

							A-46
PREPARATION
PREPARATION
Power/Standby Indicator
 
• Illuminates red in standby mode.
 
• The lighting is off while the TV remains on.
Intelligent Sensor
Adjusts picture accord-
ing 
to the surrounding 
conditions 
Only 50/60PK5 ** 
 Remote Control Sensor
FRONT PANEL CONTROLS
 
■ Image shown may differ from your TV.
NOTE
 
► TV can be placed in standby mode in order to reduce the power consumptio\
n. And TV should be 
switched off using the power switch on the TV if it will not be watched for some time, as this will 
reduce energy consumption.
 
The energy consumed during use can be significantly reduced if the level\
 of 
brightness of the picture is reduced, and this will reduce the overall r\
unning cost.
 
 CAUTION
 
► Do not step on the glass stand or subject it to any impact. It may break\
, causing possible injury from frag-
ments of glass, or the TV may fall.
 
► Do not drag the TV. The floor or the product may be damaged.
INPUTMENUOKVOLUMEPROGRAMMEPOWER
Touch Button
You can use the desired button function by touching.
SPEAKER