LG 32lc7r Owners Manual

							9
ATTACHING THE TV TO A WALL
(This feature is not available for all models.)
PREPARATION
Plasma TV models LCD TV models
2  1
■Position the TV close to the wall to avoid the possibility of it falling when pushed.
■The instructions shown below are a safer way to setup the TV, which is to fix it to the wall, avoiding the
possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury.
This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
NOTE!
G When moving the TV undo the cords first.
G Use a platform or cabinet string and large enough to support the size and weight of the TV.
G To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
2 
3 1
1
2
Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. 
(If your TV has bolts in the eyebolts, loosen then bolts.)
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with bolts (must purchase seperately) to the wall.
Ensure that both brackets are even.
3Use a strong cord (must purchase separately) to secure the TV.
Secure the cord in such a way that it becomes taught when the TV is in position.
 
						

							10
BACK COVER FOR WIRE ARRANGEMENT
PREPARATION
PREPARATION
Plasma TV models
■These models have two cable arrangement methods according to the stand type.
Connect the cables as necessary.
To connect additional equipment, see the External
equipment Setupsection of the manual.
Reinstall the C CA
AB
BL
LE
E 
 M
MA
AN
NA
AG
GE
EM
ME
EN
NT
T
as shown.2
1
3
CABLE MANAGEMENT
Grip the CABLE MANAGEMENTand push the cover upwards.
Stand type 1
Stand type 2
Arrange the cables as shown picture.
 
						

							11
PREPARATION
LCD TV models
Connect the cables as necessary.
To connect additional
equipment, see the External
equipment Setupsection.1
Install the C CA
AB
BL
LE
E 
 M
MA
AN
N-
-
A AG
GE
EM
ME
EN
NT
T
as shown.2
Bundle the cables using the
supplied twister holder.
(
This feature is not available
for all models.)
3
Hold the C CA
AB
BL
LE
E 
 M
MA
AN
NA
AG
GE
EM
ME
EN
NT
T
with both hands and pull it upward.
NOTE!
G G 
 Do not use the CABLE MANAGEMENTto lift the TV.
- If the TV is dropped, you may be injured or the TV may be damaged.
How to remove the cable management
CABLE MANAGEMENT
TWIST HOLDER
or
or
or
or(Insert it as pushing the loops on the
both sides of the cable management.)
(Pull it out as holding the loops on the both
sides of the cable management.)
 
						

							12
■The TV can be installed in various ways such as on a wall, or on a desktop etc.
■The TV is designed to be mounted horizontally.
PREPARATION
PREPARATION
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV .
4 inches 4 inches
4 inches
4 inches
Power Supply
Circuit breaker
EARTHING
Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not
possible, have a qualified electrician install a separate circuit breaker. 
Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
 
						

							
13
PREPARATION
WALL MOUNT: HORIZONTAL INSTALLATION

For adequate ventilation allow a clearance of 4” (10cm) all around the TV. Detailed installation instruc-tions
are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.
4 inches
4 inches
4 inches
4 inches
4 inches
 
						

							14
PREPARATION
AV  IN 3L/MONO
RAUDIO
VIDEO
S-VIDEO
12
VARIABLE
AUDIO OUTRGB IN
COMPONENT INAUDIO
VIDEO
AV  1 AV 2ANTENNA
       INHDMI/DVI IN HDMI INAV  1 AV 2ANTENNA
IN
VARIABLE AUDIO OUTVIDEOAUDIOCOMPONENT IN
AV  IN 3
L/MONO
RAUDIO
VIDEO
HDMI/DVI IN HDMI IN12RGB IN
S-VIDEO
AV  IN 2
L/MONO
R
AUDIO
VIDEO
S-VIDEO
HDMI IN  HDMI/DVI IN 
1
12
2
VARIABLE
AUDIO OUTRGB IN
COMPONENT IN
AV  IN 1 AV OUT
L/MONO
RAUDIO
VIDEO
ANTENNA
       IN
HDMI IN  HDMI/DVI IN 
1
12
2
VARIABLE
AUDIO OUTRGB IN
COMPONENT IN
AV  IN 1 AV OUT
L/MONO
RAUDIO
VIDEO
RS-232C IN
(CONTROL & SERVICE)
AV  IN 2
L/MONO
R
AUDIO
VIDEO
S-VIDEO
HDMI IN  HDMI/DVI IN 
1
12
2
VARIABLE
AUDIO OUTRGB IN
COMPONENT IN
AV  IN 1 AV OUT
L/MONO
RAUDIO
VIDEO
ANTENNA
       IN
HDMI IN  HDMI/DVI IN 
1
12
2
VARIABLE
AUDIO OUTRGB IN
COMPONENT IN
AV  IN 1 AV OUT
L/MONO
RAUDIO
VIDEO
RS-232C IN
(CONTROL & SERVICE)
PREPARATION
ANTENNA CONNECTION
■For optimum picture quality, adjust antenna direction.
■An antenna cable and converter are not supplied.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Outdoor
Antenna
Wall
Antenna
Socket
RF Coaxial Wire (75 ohm)
Antenna
UHF
Signal
Amplifier
VHF
■In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the 
antenna as shown above.
■If signal needs to be split for two TVs, use an antenna signal splitter for connection.
■It is recommended that 42PC5RH / 42PC5RVH / 50PC5RH / 42PC7RVH model only be used at an altitude
of less than 6561 feet (2000m) to get the best quality picture and sound.
■To prevent damage do not connect to the mains outlet until all connections are made between the devices.
 
						

							15
EXTERNAL EQUIPMENT SETUP 
HDMI IN  HDMI DVI IN 
1
2
COMPONENT IN COMPONENT INAUDIO
VIDEO
HDMI IN  HDMI DVI IN RGB IN
HDMI/DVI IN 
1
HDMI IN  HDMI DVI IN HDMI IN  HDMI/DVI IN 
12
12
EXTERNAL EQUIPMENT SETUP
HD RECEIVER SETUP
Connecting with a component cable
Connect the video outputs (
Y,  PB, PR)
of the digital TV 
top box to the C CO
OM
MP
PO
ON
NE
EN
NT
T 
 I
IN
N 
 V
VI
ID
DE
EO
O
jacks on the
TV.
Connect the audio output of the digital set-top box to 
the C CO
OM
MP
PO
ON
NE
EN
NT
T 
 I
IN
N 
 A
AU
UD
DI
IO
O
jacks on the TV.
Turn on the digital set-top box. 
(
Refer to the owner’s manual for the digital set-top box.)
Select
Component1input source using theI IN
NP
PU
UT
T
button on the remote control.
If connected to C CO
OM
MP
PO
ON
NE
EN
NT
T 
 I
IN
N2
2
, select
Component2input source.
2
3
4
1
■To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
■This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the LCD TV models.
Signal
480i/576i
480p/576p
720p/1080i
10 8 0 pComponent
Ye s
Ye s
Ye s
NoHDMI1/2
No
Ye s
Ye s
Ye s
(except VGA Models)
 
						

							HDMI IN  HDMI DVI IN 
1
2
COMPONENT IN
HDMI IN  HDMI DVI IN RGB IN
HDMI/DVI IN 
1
HDMI IN  HDMI DVI IN HDMI IN 
HDMI IN  HDMI/DVI IN 
HDMI/DVI IN 
12
1
16
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP 
Connecting a set-top box with an HDMI cable
Connect the HDMI output of the digital set-top box to
the H HD
DM
MI
I/
/D
DV
VI
I 
 I
IN
N 
 1
1 
 
or H HD
DM
MI
I 
 I
IN
N 
 2
2 
 
jack on the TV.
Select 
HDMI1 or HDMI2input source using the
I IN
NP
PU
UT
T
button on the remote control.
Turn on the digital set-top box. 
(
Refer to the owner’s manual for the digital set-top box.)2
3
1
G GTV can receive the video and audio signal simultaneously with using a HDMI cable.
G
GIf the digital set-top box supports Auto HDMI function, the output resolution of the source device will
be automatically TV to 1280x720p.
G GIf the digital set-top box player does not support Auto HDMI, you need to TV the output resolution
appropriately.
To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
NOTE!
 
						

							HDMI IN  HDMI DVI IN 
1
2
COMPONENT IN
AV  IN 1 AV  IN 1AV  OUT AV  OUT
AUDIO
(RGB/DVI)RGB(PC)
HDMI IN  HDMI DVI IN AUDIO
(RGB/DVI)RGB(PC)RGB INHDMI/DVI IN 
1
HDMI IN  HDMI DVI IN HDMI IN  HDMI/DVI IN 
12
L/MONO
12
17
EXTERNAL EQUIPMENT SETUP 
Connect the DVI output of the digital set-top box to the H HD
DM
MI
I/
/D
DV
VI
I 
 I
IN
N 
 1
1 
 
jack on the TV.
Connect the audio output of the digital set-top box to the A AU
UD
DI
IO
O(
(R
RG
GB
B/
/D
DV
VI
I)
) 
 
jack on the TV.
Turn on the digital set-top box. (
Refer to the owner’s manual for the digital set-top box.)
Select 
HDMI1 input source using the I IN
NP
PU
UT
T
button on the remote control.
2
3
4
1
Connecting with a HDMI to DVI cable
 
						

							HDMI IN  HDMI DVI IN 
HDMI IN  HDMI DVI IN 
RG
HDMI IN  HDMI DVI IN 
AV  IN 2
L/MONO
R
AUDIO
VIDEO
S-VIDEO
1
2
COMPONENT IN COMPONENT INAUDIO
VIDEO
HDMI IN  HDMI/DVI IN 
12
AV  IN 1
L/MONO
RAUDIO
VIDEO
12
18
DVD SETUP
EXTERNAL EQUIPMENT SETUP
EXTERNAL EQUIPMENT SETUP 
Connecting with a component cable
Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
YPBPR
Video output ports 
on DVD player
Y
Y
Y
YPB
B-Y
Cb
PbP
R
R-Y
Cr
Pr
Connect the video outputs (
Y,  PB, PR)
of the DVD to the
C CO
OM
MP
PO
ON
NE
EN
NT
T 
 I
IN
N 
 V
VI
ID
DE
EO
O
jacks on the TV.
Connect the audio outputs of the DVD to the C CO
OM
MP
PO
O-
-
N NE
EN
NT
T 
 I
IN
N 
 A
AU
UD
DI
IO
O
jacks on the TV.
Tu r n  on the DVD player, insert a DVD.
Select Component1input source using the I IN
NP
PU
UT
T
button
on the remote control.
If connected to C CO
OM
MP
PO
ON
NE
EN
NT
T 
 I
IN
N2
2
, select Component2
input source.
Refer to the DVD player's manual for operating instructions.
2
3
4
5
1