LG 22LG3060 Owners Manual

							
9
PREPARATION

AUDIO IN
(RGB/DVI)
YPBPRLR
VIDEO COMPONENT IN
AUDIO
EJECT 
PCMCIA
CARD SLOT 
RS-232C IN
(CONTROL & SERVICE)
SERVICEONLYRGB (PC) IN
HDMI/DVI IN
AV 1 AV 2
ANTENNA IN

5324
7810
Power Cord Socket
This TV operates on an AC power. The voltage is
indicated on the Specifications page. Never
attempt to operate the TV on DC power.
HDMI Input
Connect a HDMI signal to HDMI IN.
Or DVI(VIDEO)signal to HDMI/DVI port with DVI
to HDMI cable.
RGB/DVI Audio Input
Connect the audio from a PC or DTV.
Antenna Input
Connect RF antenna to this jack.
PCMCIA (Personal Computer Memory Card
International Association) Card Slot ( This feature is not available in all countries.) Euro Scart Socket (AV1/AV2) 
Connect scart socket input or output from an
external device to these jacks.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
Component Input
Connect a component video/audio device to
these jacks.
RGB Input
Connect the output from a PC.
SERVICE ONLY PORT1
2
3
4
5
6
7
8
9
10
6
1
9
LCD TV Models : 19/22LS4D *
 Ofrecido por www.electromanuales.com
 
						

							
10
PREPARATION
PREPARATION

13
4
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

2Assemble the parts of the S
S
t
ta
a n
n d
d  
 B
B o
od
dy
y
with
the  C
C
o
ov
ve
e r
r 
 B
B a
as
se
e
of the TV. Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the
back of the TV.

Stand Body
Cover Base
STAND INSTALLATION
(LCD TV Models: 32/37/42LG20 **, 26/32/37/42LG30
**, 32/37/42LG5
***)

AWhen assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the
product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt
can deviate from abrasion of the tightening part of the bolt.

(Only 19/22LG30**)
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the parts of the  S
S
T
T A
A N
N D
D 
 B
B O
O D
DY
Y
with  C
C
O
O V
VE
ER
R  
 B
B A
A S
SE
E
of the TV. Insert the  S
S
T
T A
A N
N D
D 
 B
B O
O D
DY
Y
into a
C
C O
O V
VE
ER
R  
 B
B A
A S
SE
E
until clicking sound.
Assemble the TV as shown.

1
2
3
Stand Body
Cover Base
 Ofrecido por www.electromanuales.com
 
						

							
11
PREPARATION
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the back of the TV.
(Only 42PG10**, 42PG20
**, 42PG30
**)

1
2
3
 Ofrecido por www.electromanuales.com
 
						

							
12
PREPARATION
PREPARATION
STAND INSTALLATION(Only 19/22LS4D*)
■Image shown may differ from your TV.

1
2
3
4
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.

Hold the 
H
H
i
in
n g
ge
e 
 B
B o
od
dy
y
and bend it upward.

Hinge Body
Insert the  S
S
t
ta
a n
n d
d  
 B
B o
od
dy
y
into the TV until clicking
sound.

Assemble the parts of the  S
S
t
ta
a n
n d
d  
 B
B o
od
dy
y
with
the C
Co
ov
ve
e r
r 
 B
B a
as
se
e
of the TV.

Cover Base
Stand Body

Swivel Stand 
(Except for 19/22LS4D
*, 50PG10
**)

After installing the TV, you can adjust the TV manually
to the left or right direction by 20 degrees to suit your
viewing position.
 Ofrecido por www.electromanuales.com
 
						

							
13
PREPARATION
DETACHING STAND(Only 19/22LS4D*)
1
2
3
Place the tv with its front facing downward on a
cushion or soft cloth.
Pull 
the C C o
ov
ve
e r
r 
 B
B a
as
se
e
backward during pressing
a button on the  S
S
t
ta
a n
n d
d  
 B
B o
od
dy
y
.
Hold 
the C
C o
ov
ve
e r
r 
 B
B a
as
se
e
and pull with shake it
backward to separate from the  S
S
t
ta
a n
n d
d  
 B
B o
od
dy
y
.
4Hold the  S
S
t
ta
a n
n d
d  
 B
B o
od
dy
y
and bend it upward.
5Pull stand body to separate from the TV during
pressing 2 latches.

■Image shown may differ from your TV.
 Ofrecido por www.electromanuales.com
 
						

							
14
PREPARATION
PREPARATION
PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOES NOT
FALL OVER.

■You should purchase necessary components to fix the TV to the wall on the market.
■Position the TV close to the wall to avoid the possibility of it falling when pushed.
■The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the
possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This
will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
NOTE
!

G When moving the TV undo the cords first.
G Use a platform or cabinet strong and large enough to support the size and weight of the TV.
G To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same. 
3
1
2
Use the eye-bolts or TV brackets/bolts to fix the TV to the wall as shown in the picture. 
(If your TV has bolts in the eyebolts, loosen these bolts.)
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the
wall.
3Use a sturdy rope to tie the TV. It is safer to tie the rope so it becomes horizontal between the wall and the
TV.

2 
1
2 
1
 Ofrecido por www.electromanuales.com
 
						

							
15
PREPARATION
BACK COVER FOR WIRE ARRANGEMENT
PLASMA TV Models
Connect the cables as necessary.
To connect additional equipment, see the E E
x
xt
te
e r
rn
n a
al
l 
  E
E q
q u
ui
ip
p m
m e
en
n t
t 
 S
S e
et
tu
u p
p
section.1

Install the  C
C
A
AB
BL
LE
E  
 M
M A
AN
N A
AG
G E
EM
M E
EN
N T
T 
 C
C L
LI
IP
P
as shown.
If your TV has the CABLE HOLDER, install it as shown and bundle the cables.2

CABLE MANAGEMENT CLIP

Hold the  C
C
A
AB
BL
LE
E  
 M
M A
AN
N A
AG
G E
EM
M E
EN
N T
T 
 C
C L
LI
IP
P
with both hands and pull it upward.
* For the 42PG10 **model, press the center of the CABLE MANAGEMENT CLIP and then lift up it.
How to remove the cable management clip

(Only 42/50PG10
**) (Only 42/50PG20**, 42/50/60PG30 **)
(Only 
42/50PG10
**) (Only 42/50PG20**, 42/50/60PG30 **)

CABLE MANAGEMENT CLIP CABLE HOLDERCABLE HOLDER
 Ofrecido por www.electromanuales.com
 
						

							
16
PREPARATION
PREPARATION
LCD TV Models:
32/37/42LG20**, 26/32/37/
42LG30 **, 32/37/42/47/52LG5
***

Connect the cables as neces-
sary.
To connect additional equip-
ment, see the External
Equipment Setup section of
the manual.1
Open the  C C
A
AB
BL
LE
E  
 M
M A
AN
N A
AG
G E
EM
M E
EN
N T
T 
 C
C L
LI
IP
P
as
shown and manage the cables.2
CABLE MANAGEMENT CLIP

Fit the  C
C
A
AB
BL
LE
E  
 M
M A
AN
N A
AG
G E
EM
M E
EN
N T
T 
 C
C L
LI
IP
P
as
shown.3
Connect the cables as necessary.
To connect additional equipment, see the
External Equipment Setup section.1
Install the CABLE MANAGEMENT CLIP as shown.2
First, press the cable management. Hold the  C C
A
AB
BL
LE
E  
 M
M A
AN
N A
AG
G E
EM
M E
EN
N T
T 
 C
C L
LI
IP
P
with both hands and pull it upward.
NOTE
!

G
GDo not use the  CABLE MANAGEMENT CLIP to lift the TV.
- If the TV is dropped, you may be injured or the TV may be damaged.
How to remove the cable management clip (LCD TV Models : 19/22LS4D *)

LCD TV Models : 19/22LS4D
*
 Ofrecido por www.electromanuales.com
 
						

							
17
PREPARATION
LCD TV Models : 19/22LG30**

Connect the cables as necessary.
To connect additional equipment, see the External Equipment Setupsection of the manual.1
Install the CABLE MANAGEMENT CLIP as shown.2
CABLE MANAGEMENT CLIP

NOTE
!

G
GDo not use the CABLE MANAGEMENT CLIP to lift the TV.
- If the TV is dropped, you may be injured or the TV may be damaged.
How to remove the cable management clip
G
GHold the  CABLE MANAGEMENT CLIP  with both hands and pull it backward.
 Ofrecido por www.electromanuales.com
 
						

							
18
PREPARATION
PREPARATION
POSITIONING YOUR DISPLAY(Only 19/22LG30**, 19/22LS4D
*)
■Image shown may differ from your TV.
■Adjust the position of the panel in various ways for
maximum comfort. • Tilt range
10~1230

LOCATION(Only 19/22LG30
**, 19/22LS4D
*)
Position your TV so that no bright light or sunlight falls directly onto the screen. Care should be taken not to
expose the tv to any unnecessary vibration, moisture, dust or heat. Also ensure that the TV is placed in a position
to allow a free flow of air. Do not cover the ventilation openings on the back cover.
If you intend to mount the TV to a wall, attach VESA standard mounting interface (optional parts) to the back of
the TV.
When you install the TV to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.
KENSINGTON SECURITY SYSTEM(Only 19/22LG30
**, 19/22LS4D
*)
The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington
Security System cable as shown below.
For the detailed installation and use of the Kensington Security System, refer to the user’s guide provided with
the Kensington Security System.
For further information, contact 
http://www.kensington.com, the internet homepage of the Kensington 
company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD
projectors.
NOTE
- The Kensington Security System is an optional accessory.
NOTES
a. If the TV feels cold to the touch, there may be a small “flicker” when when it is turned on.
This is normal, there is nothing wrong with TV.
b. Some minute dot defects may be visible on the screen, appear- ing as tiny red, green, or blue spots. However, they have no
adverse effect on the monitor's performance.
c. Avoid touching the LCD screen or holding your finger(s) 
against it for long periods of time.
Doing so may produce some temporary distortion effects on
the screen.
 Ofrecido por www.electromanuales.com