Lexmark X864dhe User Manual

Installing a flash memory or firmware card
The system board has two connections for an optional flash memory or firmware card. Only one of each may be installed,
but the connectors are interchangeable.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer, then turn...

Notes:
The entire length of the connector on the card must touch and be flush against the system board.
Be careful not to damage the connectors.
5Reattach the system board cover.
Installing an internal print server or port interface card
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices...

5Push the internal print server or port interface card firmly into the card connector on the system board.
6Insert a screw into the hole on the right side of the connector slot. Gently tighten the screw to secure the card to
the system board tray.
7Reinstall the system board.
Installing a printer hard disk
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord...

3Attach the ribbon cable to the hard disk.
4Attach the mounting plate to the hard disk with the screws.
5Press the ribbon cable connector into the hard disk connector on the system board.
Additional printer setup34
Downloaded From ManualsPrinter.com Manuals 

6Flip the hard disk over, and then press the three posts on the mounting plate into the holes on the system board.
The hard disk snaps into place.
7Reinstall the system board.
Reinstalling the system board
Warning—Potential Damage: System board electrical components are easily damaged by static electricity. Touch
something metal on the printer before touching any system board electronic components or connectors.
Note: This operation requires a #2 Phillips screwdriver.
1Gently insert the system board into...

2Replace the cover screws, and then turn them clockwise.
3Tighten the screws firmly.
Installing hardware options
Order of installation
CAUTION—TIPPING HAZARD: Floor-mounted configurations require additional furniture for stability. You must
use either a printer stand or printer base if you are using a high-capacity input tray, a duplex unit and an input
option, or more than one input option. If you purchased a multifunction printer (MFP) that scans, copies, and
faxes, you may need additional furniture....

Installing optional trays
The printer supports the following optional input sources:
2 Tray Module (two 500‑sheet trays)
2,000‑sheet dual input trays
2,000‑sheet high capacity feeder
Duplex unit
CAUTION—POTENTIAL INJURY: The printer weight is greater than 55kg (121 lbs), and requires at least four
persons or a properly rated mechanical handling system to move it safely.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up...

4Duplex unit
Note: Optional trays lock together when stacked. Remove stacked trays one at a time from the top down.
3Align the printer with the tray, and then lower the printer into place.
4Turn the printer back on.
5Set the printer software to recognize the optional input source. For more information, see “Updating available
options in the printer driver” on page 41.
Attaching cables
Connect the printer to the computer using a USB cable or Ethernet cable.
Be sure to match the following:
The USB symbol...

USB portEthernet port
Verifying printer setup
Print a menu settings page to verify that all printer options are installed correctly. A list of installed options appears
toward the bottom of the page. If an option you installed is not listed, then it is not installed correctly. Remove the
option and install it again.
Print a network setup page to verify that your printer is correctly connected to the network. This page also provides
important information that aids network printing configuration.
Printing...

Printing a network setup page
If the printer is attached to a network, then print a network setup page to verify the network connection. This page
also provides important information that aids network printing configuration.
1Make sure the printer is on and Ready appears.
2On the home screen, touch .
3Touch Reports.
4Touch Network Setup Page.
The network setup page prints and the printer returns to the home screen.
5Check the first section on the network setup page, and confirm that Status is...