Lexmark X852e User Manual

Clearing jams
121
Clearing jams
280-288 Jams
These are finisher jams. Follow the appropriate instructions to clear a jam in the finisher.
Clearing Area F
1Lift the bridge unit assembly door.
2Remove the jammed media.
3Close the door.
4Touch Continue.
Downloaded From ManualsPrinter.com Manuals 

Clearing jams
122
Clearing jams
Clearing Area G
1Open the finisher door.
2Remove the jammed media, as indicated on the operator panel.
3Close the door.
4Touch Continue.
Clearing Area H
1Lift Door H.
2Remove the jammed media.
3Close the door.
4Touch Continue.
Downloaded From ManualsPrinter.com Manuals 

Clearing staple jams
123
Clearing jams
Clearing staple jams
289 Jam
A 289 jam number indicates staples are jammed in the stapler. This requires removing the staple cartridge holder from the 
MFP.
1Check that the machine stops operations, and open Door G (front door) of the finisher.
2Hold the lever on the staple cartridge holder, and move the holder to the right (towards you).
3Firmly pull the colored tab to remove the staple cartridge.
Downloaded From ManualsPrinter.com Manuals 

Clearing staple jams
124
Clearing jams
4Use the metal tab to lift the staple guard, and then pull out the sheet of staples.
Discard the entire sheet.
5Remove any loose staples from the staple guard.
6Look through the clear covering on the bottom of the cartridge holder to make sure no staples are jammed in the 
entry throat.
7Press down on the staple guard until it snaps securely into place.
8Push the cartridge holder firmly into the stapler until the holder clicks into place.
9Close Door G.
Priming...

Clearing ADF Jams
125
Clearing jams
Clearing ADF Jams
290, 291, 292, and 294 Jams
1Remove all original documents from the ADF.
2Lift the ADF cover latch.
3Open the ADF cover.
4Raise the sheet guard.
5Turn the paper advance wheel to the left to remove any jammed pages.
6Close the ADF cover.
Paper advance 
wheel
Paper advance 
wheel
Downloaded From ManualsPrinter.com Manuals 

Clearing ADF Jams
126
Clearing jams
7Open the document cover, and remove any jammed pages.
8Close the document cover.
9Touch Continue.
293 Jam
A 293 jam indicates the MFP was sent a scan job, but found no original document in the ADF. To resolve a 293 Jam:
Touch Continue if no scan job is active when the attendance message appears. This clears the message.
Touch Cancel Job if a scan job is processing when the attendance message appears. This cancels the job and 
clears the message.
Touch Scan from...

4
Contents
Chapter 1: Learning about the MFP  .................................................................................. 8
Identifying the MFP  .......................................................................................................................................... 8
Using the scanner  ............................................................................................................................................ 8
Configured models...

Adjusting screen timeout
127
Administrative support
7Touch Submit.
8Touch Home.
Adjusting screen timeout
To  a d j u s t  t h e Screen Timeout setting:
1Make sure the MFP is on.
2Touch the Menus button on the home screen.
3Touch Settings.
4Touch General Settings.
5Touch the down arrow until Screen Timeout appears.
6Touch the left arrow to decrease the time, or touch the right arrow to increase the time.
The settings available range from 15–300 minutes.
Adjusting Power Saver
To  a d j u s t  t h e Power...

Configuring the MFP
128
Administrative support
7Touch SettingsÆ  SecurityÆ Password Protect to view what configuration settings are protected by the 
Advanced Password.
Note:Settings
Æ  SecurityÆ Password Protect and SettingsÆ  SecurityÆ  Create/Change 
Passwords
Æ  Create Change User Password can be used to restrict access with a different 
password than the Advanced Password. Use Settings
Æ  Secur ityÆ Password Protect to select the 
menus that are accessible with both an Advanced Password and a User...

Configuring the MFP
129
Administrative support
Setting the Device Lockout personal identification number (PIN)
The Device Lockout PIN allows locking and unlocking the functional state of the MFP. A locked MFP automatically buffers 
each job received to its hard disk. To initiate the printing of jobs on a locked MFP hard disk, enter the correct PIN on the 
control panel to unlock the MFP.
A locked MFP also prevents all use of the control panel except to unlock the MFP.
Note:This setting is only available...