Lexmark X 204 Service Manual

Repair information4-29
7011-2xx / 3xx
LVPS/HVPS card assembly removal 
Note:  If you are installing a new power supply for an X203 with a serial number of 5920000 or less, or an X204 
with a serial number of 5920000 or less, you will also need to install a new controller board. See “Controller 
card removal” on page 4-13. X203 / X204 machines with a serial number greater than 5920000 use power 
supply 40X6009 (110V)) / 40X6010 (220V). 
1.Remove the cover extender (if installed), paper tray,
2.Remove the...

4-30Service Manual 7011-2xx / 3xx
8.Remove four screws (C) in the bottom of the metal cover.
9.Move the cover so the connecting cables can be unplugged. 

Repair information4-31
7011-2xx / 3xx
10.Rotate the power supply assembly so the remaining cables can be removed. 
11.Remove the LVPS/HVPS card and cover. 
LVPS/HVPS to controller card cable removal 
Note:  Use the cable in part number 40X6113 machines with a serial number greater than 5920000.
1.Remove the LVPS/HVPS card. See “LVPS/HVPS card assembly removal” on page 4-29 for more 
information. 
2.Remove the controller card cover. See “Controller card removal” on page 4-13 for more information.
3.Unplug...

4-32Service Manual 7011-2xx / 3xx
Manual feed clutch assembly removal 
1.Remove the left side cover. See “Left side cover removal” on page 4-4.
2.Place the MFP on its right side. Protect the cover from being marred. 
3.Remove the four screws (A) in the gear train metal cover.
4.Remove the clip (B) from the shaft of the pick up clutch assembly. 
5.Remove the screw (C) and lever (pawl). 
6.Remove the clutch assembly. If the pieces come apart, they can be easily reassembled if necessary.  

Repair information4-33
7011-2xx / 3xx
Operator panel bezel removal
1.Remove the front flatbed cover See.“Flatbed front cover removal” on page 4-9.
2.Gently pry the bezel away from the operator panel, starting at one of the front corners and working across 
the bezel. 
3.Remove the bezel from the MFP.
Operator panel cable removal
1.Remove right cover.
2.Remove operator panel.
3.Disconnect the operator panel cable from the controller card. 

4-34Service Manual 7011-2xx / 3xx
4.Route the cable throught the flatbed assembly and the base printer top cover.
5.Remove the cable from the MFP. 

Repair information4-35
7011-2xx / 3xx
Operator panel assembly removal
Warning:  If you are replacing the operator panel and controller card, do not replace them at the same time. 
Replace both parts atthe same time will result in all settings being lost.
1.Replace the controller card first, and POR the MFP to Ready.
2.Replace the operator panel. and POR the MFP to Ready.
Note:  Do not use a new operator panel or controller card for testing purposes. on a repair.
To remove the operator panel, perform the...

4-36Service Manual 7011-2xx / 3xx
5.Remove the op panel cable (B) from the op panel.
6.Remove the op panel from the MFP. 

Repair information4-37
7011-2xx / 3xx
Paper exit guide assembly removal
1.Remove the rear cover. See “Rear cover removal” on page 4-5 for more information.
2.Remove the three screws (A) securing the exit guide. 
3.Remove the paper exit guide assembly. 
Reinstallation note: It may be necessary to rotate the gears to mesh with the fuser and drive gear.  

4-38Service Manual 7011-2xx / 3xx
Printhead removal 
Note:  Use part number 40X5776 for printers with serial number 5920000 or greater.
1.Remove the flatbed and ADF. See “Flatbed removal” on page 4-48, and “ADF assembly removal” on 
page 4-46.
2.Remove the top cover. See “Top cover removal” on page 4-8 for more information. 
3.Remove the toroid from the group of cables at the top of the controller card.
4.Unplug the printhead cables at locations J12 and J13 on the controller card and on the printhead.