Lexmark T650n User Manual

							Install Tray 
Try one or more of the following:
Install the specified tray:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Install the specified tray.
4Connect the power cord to a properly grounded outlet.
5Restart the printer.
Cancel the current job.
Install MICR Cartridge
The printer does not have a MICR cartridge installed. Install a MICR cartridge to continue printing.
Invalid Engine Code
You need to download valid engine code for the printer.
For more information, visit the Lexmark Web site at www.lexmark.com, or contact customer support.
Note: Engine code may be downloaded while this message appears on the display.
Invalid Network Code
You need to download valid network printing code for the internal print server. The internal print server is a hardware
option installed inside the printer.
Note: Network code may be downloaded while this message appears on the display.
Invalid PIN
Enter a valid PIN.
Load manual feeder with 
Try one or more of the following:
Load the specified paper in the multipurpose feeder.
Press the arrow buttons until Continue appears, and then press  to clear the message and continue printing.
If the printer finds a tray that has the correct paper type and size, then it feeds from that tray. If the printer cannot
find a tray with the correct paper type and size, then it prints from the default source.
Cancel the current job. Understanding printer messages151
Downloaded From ManualsPrinter.com Manuals 
						

							Load  with 
 is a tray or feeder, and  is a paper type or size.
Try one or more of the following:
Load the paper tray or other source with the correct paper type and size.
Cancel the current job.
Load staples
Try one or more of the following:
Replace the specified staple cartridge in the finisher.
Press the arrow buttons until Continue appears, and then press  to clear the message and continue printing.
Cancel the print job.
Maintenance
Replace the maintenance items and, if necessary, reset the printer maintenance counter.
For information on purchasing supplies, see “Ordering supplies” on page 169.
Menu access turned off by system administrator
The printer menus cannot be accessed because your system support person disabled the menus. Wait for the message
to clear.
Menus are Disabled
The printer menus are disabled. The printer settings cannot be changed from the printer control panel. Contact your
system support person for help.
Note: When menus are disabled, it is still possible to cancel a print job, print a confidential job, or print a held job.
Must be in Ready state to enter menus
The printer menus cannot be accessed at this time because the printer control panel does not show the Ready message.
Wait for the printer to complete its activity. When Ready appears, press 
.
Network/Network /Network , 
The printer is connected to the network, so the network interface is the active communication link.
Network indicates that the printer is using the standard network port built into the printer system board.
Network  indicates that an internal print server is installed inside the printer or that the printer is connected
to an external print server. Understanding printer messages152
Downloaded From ManualsPrinter.com Manuals 
						

							Network ,  indicates a network interface is the active communication link, where ,  indicates
the active interface is connected to the printer through channel y on PCI connector x. If x equals 0, then the standard
network interface is active.
Note: The current interface displays on the menus settings page.
Wait for the message to clear.
No held jobs
Wait for the message to clear.
No jobs found
The PIN you entered is not associated with any confidential print job.
Try one or more of the following:
Press the arrow buttons until Try again appears, and then press  to enter another PIN.
Press the arrow buttons until Cancel appears, and then press  to exit.
No jobs to cancel
Wait for the message to clear.
Not Ready
The printer is not ready to receive or process data, or the printer ports are offline.
No recognized file types
Either there are no files saved on the flash drive, or the files saved are not supported. Convert files to any of the following
supported file types: .pdf, .gif, .jpeg, .jpg, .bmp, .png, .tiff, .tif, .pcx, or .dcx.
Overflow bin full
Remove the stack of paper from the bin to clear the message.
Parallel/Parallel 
The printer is using a parallel cable connection. The parallel port is the active communication link.
[PJL RDYMSG]
This is the Printer Job Language (PJL) Ready message. It appears after the Ready or Power Saver message. If the
message string is too long, it is truncated.
Wait for the message to clear. Understanding printer messages153
Downloaded From ManualsPrinter.com Manuals 
						

							Power Saver
The printer is saving power while it waits for the next print job. Send a job to print to take the printer out of Power
Saver mode.
Printer busy, Continue, Quit
Try one or more of the following:
Press  to read the information from the flash drive.
Select Quit to cancel the information retrieval process.
Printing
Wait for the message to clear.
Printing from USB drive DO NOT REMOVE
Warning—Potential Damage: Do not turn the printer off or remove the flash drive while this message is displayed.
Wait for the message to clear.
Programming disk DO NOT POWER OFF
Wait for the message to clear.
Warning—Potential Damage: Do not turn the printer power off while Programming disk appears on the
display.
Programming flash DO NOT POWER OFF
Wait for the message to clear.
Warning—Potential Damage: Do not turn the printer power off while Programming flash appears on the
display.
Reading USB drive DO NOT REMOVE
Wait for the message to clear.
Ready
The printer is ready to receive print jobs.
Reattach bin 
Try one or more of the following:
Turn the printer off and then back on. Understanding printer messages154
Downloaded From ManualsPrinter.com Manuals 
						

							If the error occurs a second time:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the specified bin.
4Reattach the bin.
5Connect the power cord to a properly grounded outlet.
6Restart the printer.
If the error occurs again:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the specified bin.
4Contact Customer Support.
Press  to clear the message and print without using the specified bin.
Reattach bin  – 
Try one or more of the following:
Turn the printer off and then back on.
If the error occurs a second time:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the specified bins.
4Reattach the bins.
5Connect the power cord to a properly grounded outlet.
6Restart the printer.
If the error occurs again:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the specified bins.
4Contact Customer Support.
Press  to clear the message and print without using the specified bins.
Reattach envelope feeder
Try one or more of the following:
Turn the printer off and then back on.
If the error occurs a second time:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the envelope feeder. Understanding printer messages155
Downloaded From ManualsPrinter.com Manuals 
						

							4Reattach the envelope feeder.
5Connect the power cord to a properly grounded outlet.
6Restart the printer.
If the error occurs again:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the envelope feeder.
4Contact Customer Support.
Press  to clear the message and print without using the envelope feeder.
Remote Management Active DO NOT POWER OFF
The printer settings are being configured. Wait for the message to clear.
Warning—Potential Damage: Do not turn the printer power off while Remote Management Active appears
on the display.
Remove packaging material, check 
Remove any remaining packaging material from the specified location.
Remove paper from all bins
Remove the paper from all of the bins. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Remove paper from bin 
Remove the paper from the specified bin. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Remove paper from standard output bin
Remove the stack of paper from the standard exit bin.
Remove paper from 
Remove the paper from the specified bin. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, press 
. Understanding printer messages156
Downloaded From ManualsPrinter.com Manuals 
						

							Replace wiper
Try one or more of the following:
Replace the fuser wiper.
Press the arrow buttons until Continue appears, and then press  to clear the message and continue printing.
Resetting active bin
Wait for the message to clear.
Resetting the printer
Wait for the message to clear.
Resetting without replacing may affect print quality.
You selected No from the “Verify PC unit replaced” screen. Wait for the message to clear.
Restoring Factory Defaults
Wait for the message to clear.
When factory default settings are restored:
All downloaded resources in the printer memory are deleted. This includes fonts, macros, and symbol sets.
All settings return to the factory defaults except the Display Language setting in the Setup menu and the custom
settings in the Serial , Network, Infrared, LocalTalk, and USB menus.
Restore Held Jobs?
Try one of the following:
Press the arrow buttons until Continue appears, and then press  t o  r e s t o r e  a l l  h e l d  j o b s  s t o r e d  o n  t h e  p r i n te r
hard disk.
Press the arrow buttons until Do not restore appears, and then press . No print jobs will be restored.
Restoring Held Job(s) x/y
x represents the number of jobs being restored. y represents the total number of jobs to be restored.
Try one or more of the following:
Wait for the message to clear.
Press the arrow buttons until Quit restoring appears, and then press  to delete unrestored held jobs. Understanding printer messages157
Downloaded From ManualsPrinter.com Manuals 
						

							Routine maintenance needed
The printer needs to have routine maintenance done. Order a maintenance kit, which contains all the items necessary
to replace the pick rollers, the charge roll, the transfer roller, and the fuser.
Securely clearing disk space
The printer hard disk wiping process needs to recover. The message clears when all blocks are cleared.
Serial 
The printer is using a serial cable connection. The serial port is the active communication link.
Some held jobs were lost
Try one or more of the following:
Press the arrow buttons until Continue appears, and then press  to clear the message and continue printing.
Cancel the current print job.
Staples  empty or misfed
Load the specified staple cartridge into the finisher to clear the message and continue stapling.
Staples  low or missing
Load the specified staple cartridge in the finisher to clear the message.
Standard Bin Full
Remove the stack of paper from the standard exit bin to clear the message.
Submitting selection
Wait for the message to clear.
Too many failed panel logins
The printer is now in a lockout mode because:
You attempted to log in too many times with an incorrect PIN
You attempted to log in using an incorrect password number for access to a printer feature, setting, or menu that
you do not have access to.
Note: There is a defined limit on the number of login attempts. Once the limit is reached, this message appears and
the printer enters a lockout mode. The message remains on the printer control panel, and any further attempts to
enter menus is denied until the defined time out expires. The time out duration is set by your system support
person. Understanding printer messages158
Downloaded From ManualsPrinter.com Manuals 
						

							Wait for the message to clear once the time out expires, and then:
Enter the correct PIN to access any held jobs
See your system support person if you need a password number to enter a specific printer feature, setting, or menu
that is blocked from your use without the number.
Toner low
Try one or more of the following:
Replace the print cartridge.
Press  to clear the message and continue printing.
Tray  Empty
Load paper in the tray to clear the message.
Tray  Low
Load paper in the specified tray to clear the message.
Tray  Missing
Insert the specified tray into the printer.
Unsupported disk
An unsupported printer hard disk has been installed. Remove the unsupported device, and then install a supported
one.
Unsupported USB device, please remove
Remove the unrecognized USB device.
Unsupported USB hub, please remove
Remove the unrecognized USB hub.
USB/USB 
The printer is using a USB cable connection. The USB port is the active communication link.
USB drive removed
Try one or more of the following:
Wait for the message to clear.
Insert the flash drive. Understanding printer messages159
Downloaded From ManualsPrinter.com Manuals 
						

							View supplies
This message shows the current level of supplies.
Waiting
The printer has received data to print, but is waiting for an End‑of‑Job command, a Form Feed command, or additional
data.
Try one or more of the following:
Press  to print the contents of the buffer.
Cancel the current print job.
30 Invalid refill, change cartridge
Remove the print cartridge, and then install a supported one.
31 Replace defective cartridge
Remove the defective print cartridge, and then install a new one.
32 Cartridge part number unsupported by device
Remove the print cartridge, and then install a supported one.
34 Short paper
Try one or more of the following:
Load the appropriate paper in the tray.
Press the arrow buttons until Continue appears, and then press  to clear the message and print the job
using a different paper tray.
Check tray length and width guides and make sure the paper is properly loaded in the tray.
For Windows users, check the Print Properties settings to make sure the print job is requesting the correct paper
size and type.
For Macintosh users, check the Print dialog settings to make sure the print job is requesting the correct paper size
and type.
Check that the paper size is correctly set. For example, if the MP Feeder Size is set to Universal, make sure the paper
is large enough for the data being printed.
Cancel the current print job. Understanding printer messages160
Downloaded From ManualsPrinter.com Manuals