Lexmark T650n User Manual

Install Tray 
Try one or more of the following:
Install the specified tray:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Install the specified tray.
4Connect the power cord to a properly grounded outlet.
5Restart the printer.
Cancel the current job.
Install MICR Cartridge
The printer does not have a MICR cartridge installed. Install a MICR cartridge to continue printing.
Invalid Engine Code
You need to download valid engine code for the printer.
For more information, visit the...

Load  with 
 is a tray or feeder, and  is a paper type or size.
Try one or more of the following:
Load the paper tray or other source with the correct paper type and size.
Cancel the current job.
Load staples
Try one or more of the following:
Replace the specified staple cartridge in the finisher.
Press the arrow buttons until Continue appears, and then press  to clear the message and continue printing.
Cancel the print job.
Maintenance
Replace the maintenance items and, if necessary, reset the printer...

Network ,  indicates a network interface is the active communication link, where ,  indicates
the active interface is connected to the printer through channel y on PCI connector x. If x equals 0, then the standard
network interface is active.
Note: The current interface displays on the menus settings page.
Wait for the message to clear.
No held jobs
Wait for the message to clear.
No jobs found
The PIN you entered is not associated with any confidential print job.
Try one or more of the following:
Press...

Power Saver
The printer is saving power while it waits for the next print job. Send a job to print to take the printer out of Power
Saver mode.
Printer busy, Continue, Quit
Try one or more of the following:
Press  to read the information from the flash drive.
Select Quit to cancel the information retrieval process.
Printing
Wait for the message to clear.
Printing from USB drive DO NOT REMOVE
Warning—Potential Damage: Do not turn the printer off or remove the flash drive while this message is displayed....

If the error occurs a second time:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the specified bin.
4Reattach the bin.
5Connect the power cord to a properly grounded outlet.
6Restart the printer.
If the error occurs again:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the specified bin.
4Contact Customer Support.
Press  to clear the message and print without using the specified bin.
Reattach bin  – 
Try one or more of the following:
Turn the...

4Reattach the envelope feeder.
5Connect the power cord to a properly grounded outlet.
6Restart the printer.
If the error occurs again:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the envelope feeder.
4Contact Customer Support.
Press  to clear the message and print without using the envelope feeder.
Remote Management Active DO NOT POWER OFF
The printer settings are being configured. Wait for the message to clear.
Warning—Potential Damage: Do not turn the printer power off...

Replace wiper
Try one or more of the following:
Replace the fuser wiper.
Press the arrow buttons until Continue appears, and then press  to clear the message and continue printing.
Resetting active bin
Wait for the message to clear.
Resetting the printer
Wait for the message to clear.
Resetting without replacing may affect print quality.
You selected No from the “Verify PC unit replaced” screen. Wait for the message to clear.
Restoring Factory Defaults
Wait for the message to clear.
When factory default...

Routine maintenance needed
The printer needs to have routine maintenance done. Order a maintenance kit, which contains all the items necessary
to replace the pick rollers, the charge roll, the transfer roller, and the fuser.
Securely clearing disk space
The printer hard disk wiping process needs to recover. The message clears when all blocks are cleared.
Serial 
The printer is using a serial cable connection. The serial port is the active communication link.
Some held jobs were lost
Try one or more of...

Wait for the message to clear once the time out expires, and then:
Enter the correct PIN to access any held jobs
See your system support person if you need a password number to enter a specific printer feature, setting, or menu
that is blocked from your use without the number.
Toner low
Try one or more of the following:
Replace the print cartridge.
Press  to clear the message and continue printing.
Tray  Empty
Load paper in the tray to clear the message.
Tray  Low
Load paper in the specified tray to...

View supplies
This message shows the current level of supplies.
Waiting
The printer has received data to print, but is waiting for an End‑of‑Job command, a Form Feed command, or additional
data.
Try one or more of the following:
Press  to print the contents of the buffer.
Cancel the current print job.
30 Invalid refill, change cartridge
Remove the print cartridge, and then install a supported one.
31 Replace defective cartridge
Remove the defective print cartridge, and then install a new one.
32...