Lexmark T650dtn User Manual

							DescriptionWhere to find (North America)Where to find (rest of world)
E-mail supportFor e-mail support, visit our Web site:
www.lexmark.com.
1Click SUPPORT.
2Click Technical Support.
3Select your printer type.
4Select your printer model.
5From the Support Tools section, click
e-Mail Support.
6Complete the form, and then click
Submit Request.E‑mail support varies by country or region,
and may not be available in some instances.
Visit our Web site at www.lexmark.com.
Select a country or region, and then select
the Customer Support link.
Note: For additional information about
contacting Lexmark, see the printed
warranty that came with your printer.
Printer configurations
Basic model
1
2
3
4
FeaturePaper Capacity*
1Standard exit bin 350 or 550 sheets
2Printer control panel Not applicable
3Multipurpose feeder 100 sheets
4Standard tray (Tray 1) 250 or 550 sheets
* Based on 75 g/m2 (20 lb.) paper.
Fully configured model
CAUTION—TIPPING HAZARD: Floor-mounted configurations require additional furniture for stability. You must
use either a printer stand or printer base if you are using a high-capacity input tray, a duplex unit and an input
option, or more than one input option. If you purchased a multifunction printer (MFP) that scans, copies, and
faxes, you may need additional furniture. For more information, see www.lexmark.com/multifunctionprinters. Learning about the printer11
Downloaded From ManualsPrinter.com Manuals 
						

							1
2
3
4
56
7
9
8
Feature/OptionPaper Capacity1
1
5‑bin mailbox2500 sheets
25‑bin mailbox 500 sheets
3Envelope feeder 85 envelopes
4Standard tray (Tray 1) 250 or 550 sheets
5
Duplex unit
3Not applicable
6Optional tray (Tray 2) 250 or 550 sheets
7Optional tray (Tray 3) 250 or 550 sheets
8Optional 2000‑sheet tray (Tray 4) 2000 sheets
9Caster base Not applicable
1 Based on 75 g/m2 (20 lb.) paper.
2 The printer supports up to three output expander units, two 5-bin mailboxes, one high capacity output expander (not
depicted), or one stapler unit (not depicted).
3 An optional duplex unit is available for basic models with a 250‑sheet standard tray. Models with a 550‑sheet standard
tray may have an internal duplex unit.
Learning about the printer12
Downloaded From ManualsPrinter.com Manuals 
						

							Selecting a location for the printer
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any
options, leave enough room for them also. It is important to:
Make sure airflow in the room meets the latest revision of the ASHRAE 62 standard.
Provide a flat, sturdy, and stable surface.
Keep the printer:
–Away from the direct airflow of air conditioners, heaters, or ventilators
–Free from direct sunlight, humidity extremes, or temperature fluctuations
–Clean, dry, and free of dust
Allow the following recommended amount of space around the printer for proper ventilation:
5
1
23
4
1Right Side 31 cm (12 in.)
2Left Side 31 cm (12 in.)
3Front 51 cm (20 in.)
4Rear 31 cm (12 in.)
5
Top
1137 cm (54 in.)
1 Allows for addition of all output options.
Learning about the printer13
Downloaded From ManualsPrinter.com Manuals 
						

							Understanding the printer control panel
1234
5 6
7 8 9
ItemDescription
1Display Shows messages and pictures that communicate the status of the printer
2Navigation buttons
Press the up or down arrow buttons to scroll through menus or menu items, or to increase or
decrease a value when entering numbers.
Press the left or right arrow buttons to scroll through menu settings (also called values or
options), or to scroll through text that rolls to another screen.
3Select
Opens a menu item and displays the available values or settings. The current setting is
indicated by an asterisk (*).
Saves a displayed menu item as the new user default setting.
Notes:
When a new setting is saved as the user default setting, it remains in effect until a new
setting is saved or until factory defaults are restored.
Settings chosen from a software program can also change or override the user default
settings selected from the printer control panel.
4Keypad Enter numbers or symbols on the display.
5Back
Returns the display to the previous screen
6Indicator light Indicates the printer status:
Off—The power is off.
Blinking green—The printer is warming up, processing data, or printing.
Solid green—The printer is on, but idle.
Solid red—Operator intervention is needed.
7Stop
Stops all printer activity
A list of options is offered once Stopped appears on the display.
Learning about the printer14
Downloaded From ManualsPrinter.com Manuals 
						

							ItemDescription
8Menu
Opens the menu index
Note: The menus are available only when the printer is in the Ready state.
9USB port Insert a flash drive into the front of the printer to print saved files.
Note: Only the front USB port supports flash drives.
Learning about the printer15
Downloaded From ManualsPrinter.com Manuals 
						

							Additional printer setup
Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well,
and unplug any cables going into the printer.
Available internal options
Memory cards
–Printer memory
–Flash memory
–Fonts
Firmware cards
–Bar Code and Forms
–IPDS and SCS/TNe
–PrintCryptionTM
Printer hard disk
LexmarkTM Internal Solutions Ports (ISP)
–RS‑232‑C Serial ISP
–Parallel 1284‑B ISP
–MarkNetTM N8150 802.11 b/g/n Wireless ISP
–MarkNet N8130 10/100 Fiber ISP
–MarkNet N8120 10/100/1000 Ethernet ISP
All of these options may not be available. For more information, contact the place where you purchased the printer. Additional printer setup16
Downloaded From ManualsPrinter.com Manuals 
						

							Accessing the system board to install internal options
Note: This task requires a flathead screwdriver.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well,
and unplug any cables going into the printer.
1Open the system board door.
2Loosen the screw on the system board cover.
Additional printer setup17
Downloaded From ManualsPrinter.com Manuals 
						

							3Remove the system board cover.
4Use the illustration below to locate the appropriate connector.
Warning—Potential Damage: System board electronic components are easily damaged by static electricity.
Touch something metal on the printer before touching any system board electronic components or connectors.
1
2
3
1Firmware and flash memory card connectors
2Memory card connector
3Lexmark Internal Solutions Port or printer hard disk connector
Additional printer setup18
Downloaded From ManualsPrinter.com Manuals 
						

							Installing a memory card
Note: This task requires a flathead screwdriver.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well,
and unplug any cables going into the printer.
Warning—Potential Damage: System board electronic components are easily damaged by static electricity. Touch
something metal on the printer before touching any system board electronic components or connectors.
An optional memory card can be purchased separately and attached to the system board. To install the memory card:
1Access the system board.
1
2
3
2Unpack the memory card.
Note: Avoid touching the connection points along the edge of the card.
3Open the memory card connector latches.
Additional printer setup19
Downloaded From ManualsPrinter.com Manuals 
						

							4Align the notches on the memory card with the ridges on the connector.
2
1
1Notches
2Ridges
5Push the memory card straight into the connector until it snaps into place.
6Replace the system board cover and close the system board door.
1
2
3
Installing a flash memory or firmware card
Note: This task requires a flathead screwdriver. Additional printer setup20
Downloaded From ManualsPrinter.com Manuals