Lexmark E260d User Manual

Menu itemDescription
Contrast
0–5Adjusts the degree of difference between levels of gray in printed output
Notes:
0 is the factory default setting.
Higher settings show more difference between levels of gray.
PostScript menu
Menu itemDescription
Print PS Error
Off
OnPrints a page containing the PostScript error
Note: Off is the factory default setting.
Font Priority
Resident
FlashEstablishes the font search order
Notes:
Resident is the factory default setting.
A formatted optional flash memory card must...

Menu itemDescription
Symbol Set
Specifies the font ID and font name that compose each symbol set
Notes:
10U PC-8 is the US factory default setting.
12U PC-850 is the international factory default setting.
PCL Emulation Settings
Point Size
1.00–1008.00Changes the point size for scalable typographic fonts
Notes:
12 is the factory default setting.
Point Size refers to the height of the characters in the font. One point equals
approximately 1/72 of an inch.
Point sizes can be increased or decreased in...

Menu itemDescription
PCL Emulation Settings
Auto LF after CR
Off
OnSpecifies whether the printer automatically performs a line feed (LF) after a
carriage return (CR) control command
Note: Off is the factory default setting.
Tray Renumber
Assign MP Feeder
Off
None
0–199
Assign Tray 
Off
None
0–199
Assign Manual Paper
Off
None
0–199
Assign Man Env
Off
None
0–199Configures the printer to work with printer software or programs that use
different source assignments for trays, drawers, and feeders
Notes:
Off...

Maintaining the printer
Periodically, certain tasks are required to maintain optimum print quality.
Cleaning the exterior of the printer
1Make sure that the printer is turned off and unplugged from the wall outlet.
CAUTION—SHOCK HAZARD: To avoid the risk of electric shock when cleaning the exterior of the printer,
unplug the power cord from the wall outlet and disconnect all cables to the printer before proceeding.
2Remove all paper from the printer.
3Dampen a clean, lint-free cloth with water....

Ordering supplies
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies
dealers in your area. In other countries or regions, visit the Lexmark Web Site at www.lexmark.comor contact the place
where you purchased the printer.
Note: All life estimates for printer supplies assume printing on letter- or A4-size plain paper.
Ordering toner cartridges
When 88 Cartridge is Low appears or when the print becomes faded, you may be able to extend the life...

Ordering a photoconductor kit
Depending on your printer model, the printer issues a message or a light sequence to let you know the photoconductor
kit is near its end of life. At this time, order a photoconductor kit. You can also see the status of the photoconductor
kit by printing a network setup page.
Part namePart number
Photoconductor kitE260X22G
Replacing supplies
Replacing the toner cartridge
Light sequence
Toner is low
 - On
 - On
When the Toner is Low light sequence appears, or when you...

To replace the toner cartridge:
1Open the front door by pressing the button on the left side of the printer and lowering the door.
2Press the button on the base of the photoconductor kit, and then pull the toner cartridge out using the handle.
3Unpack the new toner cartridge.
Warning—Potential Damage: When replacing a toner cartridge, do not leave the new cartridge exposed to direct
light for an extended period of time. Extended light exposure can cause print quality problems.
4Rotate the cartridge in...

5Install the new toner cartridge by aligning the rollers on the toner cartridge with the arrows on the tracks of the
photoconductor kit. Push the toner cartridge in until it clicks into place.
6Close the front door.
Replacing the photoconductor kit
The printer displays the Photoconductor life warning or Replace photoconductor light sequence when the
photoconductor kit reaches the page maximum.
Light sequences
Photoconductor life warning
 - On
Maintaining the printer
88
Downloaded From ManualsPrinter.com...

Replace photoconductor
 - Blinking
 - Blinking
 - On
When any of the light sequences occur, order a new photoconductor kit. While the printer may continue to function
properly after the photoconductor kit has reached its official end-of-life, print quality significantly decreases.
Note: The photoconductor kit is a single item.
To replace the photoconductor kit:
1Turn off the printer.
2Pull the photoconductor kit and toner cartridge together as a unit out of the printer by pulling on the toner cartridge...

Place the unit on a flat, clean surface.
3Press the button on the base of the photoconductor kit, and then pull the toner cartridge up and out using the
handle.
4Unpack the new photoconductor kit.
Warning—Potential Damage: Be careful not to touch the photoconductor drum. Doing so may affect the print
quality of future print jobs.
5Insert the toner cartridge into the photoconductor kit by aligning the rollers on the toner cartridge with the tracks.
Push the toner cartridge in until it clicks into place....