Lexmark E260d User Manual

6Install the unit into the printer by aligning the arrows on the guides of the unit with the arrows in the printer. Push
the unit fully in.
7After replacing the photoconductor kit, reset the photoconductor counter:
Open the front door and then press and hold 
 until all the lights cycle.
Warning—Potential Damage: Resetting the photoconductor counter without replacing the photoconductor kit
may damage your printer and void your warranty.
8Close the front door.
Moving the printer
Before moving the printer...

Shipping the printer
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.
Maintaining the printer
92
Downloaded From ManualsPrinter.com Manuals 

Administrative support
Finding advanced networking and administrator information
For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD and the
Embedded Web Server Administrators Guide on the Lexmark Web site at http://support.lexmark.com.
Restoring the factory default settings
If your printer is connected to a computer by a USB or parallel cable, use the Local Printer Settings Utility for Windows
or Printer Settings for Macintosh.
1Open the utility.
2Do one...

Clearing jams
Avoiding jams
The following hints can help you avoid jams:
Paper tray recommendations
Make sure the paper lies flat in the tray.
Do not remove a tray while the printer is printing.
Do not load a tray while the printer is printing. Load it prior to printing, or wait for a prompt to load it.
Do not load too much paper. Make sure the stack height does not exceed the indicated maximum height.
Make sure the guides in the tray or the multipurpose feeder are properly positioned and are not...

Access pointDescription
1Push button to open the front door. Inside this door is the unit housing the toner cartridge and photoconductor
kit.
2Standard exit bin
3Front door
4Manual feeder door
5Standard 250-sheet tray (Tray 1)
6Optional tray (Tray 2)
7Rear door
Understanding jam lights and access locations
The jam lights and messages are shown, along with brief instructions on how to access each jam.
Note: The jam messages listed appear on the virtual display of the Embedded Web Server.
200.yy Paper jam...

Try one of the following:
Remove Tray 1.
Open the front door, and then remove the photoconductor kit and toner cartridge unit.
201.yy Paper jam
 - On
 - On
 - On
Open the front door, and then remove the photoconductor kit and toner cartridge unit.
202.yy Paper jam
 - On
 - On
 - On
Open the front door, and then open the rear door.
Clearing jams
96
Downloaded From ManualsPrinter.com Manuals 

231.yy Paper jam
 - On
 - Blinking
 - On
Open the front door, and then open the rear door.
233.yy Paper jam
 - On
 - Blinking
 - Blinking
 - On
Try one of the following:
Remove Tray 1, and then depress the lever.
Open the front door, and then open the rear door.
234.yy Paper jam
 - On
 - Blinking
 - On
Try one of the following:
Open the front door, and then open the rear door.
Remove Tray 1, and then depress the lever.
Clearing jams
97
Downloaded From ManualsPrinter.com Manuals 

235.yy Paper jam
 - On
 - Blinking
 - Blinking
 - On
Remove the jam from the standard exit bin.
24x.yy Paper jam
 - On
 - On
 - On
 - On
Try one of the following:
Remove Tray 1.
Open the front door, and then remove the photoconductor kit and toner cartridge unit.
Remove Tray 2.
Clearing jams
98
Downloaded From ManualsPrinter.com Manuals 

251.yy Paper jam
 - On
 - On
 - On
 - On
Remove the jam from the manual feeder.
Clearing jams behind the photoconductor kit and toner cartridge
1Push the release button, and then lower the front door.
Clearing jams
99
Downloaded From ManualsPrinter.com Manuals 

2Lift and pull the unit containing the photoconductor kit and the toner cartridge out of the printer. Set the unit aside
on a flat, clean surface.
Warning—Potential Damage: Do not touch the photoconductor on the underside of the photoconductor kit. Use
the cartridge handle whenever you are holding the cartridge.
CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching.
3Remove the jammed paper.
Note: If the...