Lexmark E250d User Manual

							51Loading the 250-sheet tray
5Adjust the side paper guides to fit lightly against the paper stack.
6Insert the 250-sheet paper tray.Downloaded From ManualsPrinter.com Manuals 
						

							52Loading the 250-sheet tray
7Extend the paper support on the output bin.
Extending the tray for legal- or folio-size paper
To load legal- or folio-size paper, extend the tray. You may also attach a dust cover (if available on your printer model) on 
the back of the printer to protect the tray while it is extended.
1Press down on the latch at the back of the tray, and expand the tray until the extender locks into place.Downloaded From ManualsPrinter.com Manuals 
						

							53Loading the 250-sheet tray
Attaching the dust cover
The dust cover helps protect the tray from the environment. It also keeps the tray from being knocked out of position while 
it is extended.
Attach the dust cover to the back of the printer by aligning the tabs on the cover to the holes on the printer, then snap the 
cover into place.
Note:This feature may not be available for some models.Downloaded From ManualsPrinter.com Manuals 
						

							54Loading the manual feeder
Loading the manual feeder
The manual feeder is located at the front of the printer and can only feed one sheet of print media at a time. You can use 
the manual feeder to make quick runs of paper types or sizes that are not currently loaded in the tray. You must set the 
paper size before using the manual feeder. For more information, see your driver CD, or see Using the Local Printer 
Settings Utility on page75.
For information on acceptable print media to use in the manual feeder, see Selecting print media on page43. Using only 
the specified print media helps prevent paper jams and print-quality problems.
To load the manual feeder:
1Place a sheet of the selected print media, 
print side facing up, at the center of the 
manual feeder, but only to the point where its 
leading edge can contact the paper guides. 
Otherwise, the printer will engage the print 
media too soon and likely skew the print job.
2Adjust the paper guides to the print media 
width.
3Hold both sides of the print media close to 
the manual feeder, and push it into the 
printer until it automatically engages.
There is a brief pause between the time the 
printer engages the print media and when it 
feeds into the printer.
Note:Do not force the print media into 
the feeder. Forcing the media 
causes jams.
•Insert envelopes with the flap side down and with the stamp area as shown.
•Hold transparencies by the edges, and avoid touching the print side. Oil from your fingers can affect print quality.
•Load letterhead faceup, with the top of the sheet entering first.Downloaded From ManualsPrinter.com Manuals 
						

							55Using the rear exit
Using the rear exit
The single-sheet rear exit provides a straight-through paper path to help reduce curling and potential jams. This is 
especially useful for specialty media, such as transparencies, labels, card stock, or index cards.
To use the rear exit, open the rear exit door. When the rear exit door is open, all print media comes out the rear exit. When 
closed, all media is sent to the output bin on top of the printer.
Note:If you print a multiple-page job with the rear exit door open, the print speed may slow down.Downloaded From ManualsPrinter.com Manuals 
						

							56Clearing jams
Clearing jams
When a paper jam occurs, the printer stops and the control panel Paper Jam and Continue lights come on. 
Press and release Continue twice quickly to display the specific secondary error paper jam light sequence. See 
Secondary error codes on page25 for more information.
We recommend clearing the entire paper path when a paper jam occurs.
1Remove all paper from the 150-sheet output bin.
2If you are feeding paper from the 250-sheet tray, remove the tray. 
3Remove the jammed pages.Downloaded From ManualsPrinter.com Manuals 
						

							57Clearing jams
4With the tray removed, press down on the green duplex flap to remove the jammed pages from the duplex area.
5Install the 250-sheet paper tray.Downloaded From ManualsPrinter.com Manuals 
						

							58Clearing jams
6Open the front door, and remove the print cartridge assembly.
7Lift the green flap at the front of the printer, and remove the jammed pages from behind the flap.CAUTION:The fuser or fuser area may be hot.Downloaded From ManualsPrinter.com Manuals 
						

							59Clearing jams
8Open the rear exit door, and remove the jammed pages.
9After you have cleared the jammed pages, reinstall the print cartridge assembly, and securely close all the printer 
doors.
10Press Continue to resume printing.
Note:Jam recovery is set to Auto by default. When jam recovery is set to Auto, the memory that holds the 
image of a page may be reused after the page is printed but before it has successfully exited the 
printer if that memory is needed for another use. Therefore, a jammed page may or may not be 
reprinted, depending on the overall memory usage of the printer. Downloaded From ManualsPrinter.com Manuals 
						

							60 5
Printing tasks
Manually feeding a print job
The manual feeder is located at the front of the printer and can only feed one sheet of print media at a time. For information 
on acceptable print media to use in the manual feeder, see What types of print media can be loaded? on page41.
When using the manual feeder, send the print job to the printer before loading the print media. When the printer is ready, it 
will display the Load Manual Feeder light sequence, at which point you should load the print media.
To manually feed a print job:
1From the computer software application, select Fileà Print.
2Click Properties (or Options, Printer, or Setup, depending on the application) to view the printer driver settings.
3Click the Paper tab.
4Select Manual paper from the Paper tray drop-down list.
5Select the appropriate Paper size and type. See Using the Local Printer Settings Utility on page75 for more 
information.
6Click OK.
7Click OK on the Print window to send the job to print.
The printer displays the Load Manual Feeder light sequence.
8Place a sheet of the selected print media, print side facing up, at the center of the manual feeder, but only to the 
point where its leading edge can contact the paper guides.
•Hold transparencies by the edges, and avoid touching the print side. Oil from your fingers can affect print 
quality.
•Insert envelopes with the flap side facedown (the stamp area should enter the printer last).
•Load letterhead faceup, with the top of the sheet entering the printer first.Downloaded From ManualsPrinter.com Manuals