Lexmark E250d User Manual

							91Print quality problems
Cleaning the printhead lens
Some print quality problems can be solved by cleaning the printhead lens.
1Turn the printer off.
2Press the button on the left side of the printer to release and lower the front door.
3Remove the print cartridge assembly by pulling on the toner cartridge handle.
Note:Do not press the button on the print cartridge assembly.
Place the print cartridge assembly on a flat, clean surface.Downloaded From ManualsPrinter.com Manuals 
						

							92Print quality problems
4Locate the glass printhead lens within the recessed area in the top of the printer.
5Gently wipe the printhead lens with a clean, dry, lint-free cloth.
Warning:Not using a clean, dry, lint-free cloth may result in damage to the printhead lens.
6Install the print cartridge assembly into the printer by aligning the arrows on the guides of the print cartridge 
assembly with the arrows on the tracks in the printer and pushing the print cartridge assembly in as far as it will go.
7Close the front door.
8Turn the printer on.Downloaded From ManualsPrinter.com Manuals 
						

							Notices
93 Notices
Conventions
Electronic emission notices
Federal Communications Commission (FCC) 
compliance information statement
The Lexmark E250d and E250dn (4512-220 and 4512-230) have 
been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. Operation is subject 
to the following two conditions: (1) this device may not cause 
harmful interference, and (2) this device must accept any 
interference received, including interference that may cause 
undesired operation.
The FCC Class B limits are designed to provide reasonable 
protection against harmful interference in a residential installation. 
This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the 
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and 
receiver.
•Connect the equipment into an outlet on a circuit different 
from that to which the receiver is connected.
•Consult your point of purchase or service representative for 
additional suggestions.
The manufacturer is not responsible for any radio or television 
interference caused by using other than recommended cables or by 
unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the users 
authority to operate this equipment.
Note:To assure compliance with FCC regulations on 
electromagnetic interference for a Class B computing device, use a 
properly shielded and grounded cable such as Lexmark part 
number1021231 for parallel attach or 1021294 for USB attach. Use 
of a substitute cable not properly shielded and grounded may result 
in a violation of FCC regulations.
Any questions regarding this compliance information statement 
should be directed to:
Director of Lexmark Technology & Services
Lexmark International, Inc.
740 West New Circle Road
Lexington, KY   40550
(859) 232-3000
Industry Canada compliance statement
This Class B digital apparatus meets all requirements of the 
Canadian Interference-Causing Equipment Standard ICES-003.
Avis de conformité aux normes de l’industrie du Canada
Cet appareil numérique de classe B est conforme aux exigences de 
la norme canadienne relative aux équipements pouvant causer des 
interférences NMB-003.
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC 
Council directives 89/336/EEC and 73/23/EEC on the 
approximation and harmonization of the laws of the Member States 
relating to electromagnetic compatibility and safety of electrical 
equipment designed for use within certain voltage limits. Note:A note identifies something that could help you.
CAUTION:A caution identifies something that could cause you harm.
Warning:A warning identifies something that could damage your product hardware or software.Downloaded From ManualsPrinter.com Manuals 
						

							Electronic emission notices
94Notices
A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing and Technical Support, 
Lexmark International, S.A., Boigny, France.
This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.
Hot surface notice
Power regulation notice
Warning:Electrical surges can be very destructive to equipment connected to AC power sources.
If you plan to operate your printer at a voltage exceeding the voltage range(s) in the following table, you must attach a suitably rated and 
certified power-regulating device (such as a voltage stabilizer or UPS device) to the printer power supply. Your warranty may not cover 
damages caused by power surges.
Japanese VCCI notice
Korean MIC statementNominal Voltage RangeMaximum Voltage Range
100V–127V AC90V–135V AC
220V–240V AC198V–254V ACDownloaded From ManualsPrinter.com Manuals 
						

							Noise emission levels
95Notices
Noise emission levels
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
Product energy consumption
The following table documents the power consumption characteristics of the product
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be 
substantially higher than the average.
Off mode
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, 
disconnect the power cord from the wall outlet.
Total energy usage
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, 
the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total 
product energy usage is the sum of each modes energy usage.
ENERGY STAR1-meter average sound pressure, dBA
Printing52
Idlinginaudible
Quiet Mode49
Sleep / Power Saver ModeinaudibleModeDescriptionPower consumption
ReadyThe product is on, but idle.70W
PrintingThe product is generating hard-copy output from 
electronic inputs.500 W
Sleep / Power SaverThe product is in energy-saving mode.20WDownloaded From ManualsPrinter.com Manuals 
						

							Waste from Electrical and Electronic Equipment (WEEE) directive
96Notices
Waste from Electrical and Electronic Equipment (WEEE) 
directive
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We 
encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at 
www.lexmark.com for your local sales office phone number.
Laser advisory label
A laser notice label may be affixed to this printer.
LUOKAN 1 LASERLAITE
VAROITUS! Laitteen käyttäminen muulla kuin tässä käyttoohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 
ylittävälle  näkymättömälle lasersäteilylle.
KLASS 1 LASER APPARAT
VARNING! Om apparaten används på annat sätt än i denna bruksanvisning specificerats, kan avnändaren utsättas för osynlig 
laserstrålning, som överskrider gränsen för laserklass 1.
Laser notice
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere 
is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 5 milliwatt 
gallium arsenide laser operating in the wavelength region of 770-795 nanometers. The laser system and printer are designed so there is 
never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
Statement of Limited Warranty for Lexmark E250d and E250dn
Lexmark International, Inc. Lexington, KY
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country-specific warranty 
information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark 
Remarketer, referred to in this statement as “Remarketer.”
Limited warranty
Lexmark warrants that this product:
•Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
•Is, during normal use, free from defects in material and workmanshipDownloaded From ManualsPrinter.com Manuals 
						

							Statement of Limited Warranty for Lexmark E250d and E250dn
97Notices
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at 
Lexmarks option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. 
To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of 
the warranty period. You should transfer proof of original purchase and this statement to that user.
Limited warranty service
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the 
warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are 
substantially used up, depleted, or consumed. 
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the 
Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or 
damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. 
The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty 
service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless 
directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World 
Wide Web at http://support.lexmark.com.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, 
technical support may not be available or only be available for a fee.
Extent of limited warranty
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any 
product.
Warranty service does not include repair of failures caused by:
•Modification or unauthorized attachments
•Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
•Unsuitable physical or operating environment
•Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
•Operation of a product beyond the limit of its duty cycle
•Use of printing media outside of Lexmark specifications
•Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
•Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR 
REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH 
RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF 
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY 
NOT BE DISCLAIMED UNDER
APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL 
APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT 
ANY TIME WITHOUT NOTICE.
Limitation of liability
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of 
Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the 
following paragraph.
Lexmarks liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the 
damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property 
for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, 
INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a 
Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.Downloaded From ManualsPrinter.com Manuals 
						

							Statement of Limited Warranty for Lexmark E250d and E250dn
98Notices
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmarks and its Suppliers and 
Remarketers limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Additional rights
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or 
consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.Downloaded From ManualsPrinter.com Manuals 
						

							99  Index
A
Auto CR after LF (Setup menu)39
Auto LF after CR (Setup menu)39
B
booklets65
Busy light11
C
canceling a print job67
card stock47
characteristics, print media
paper43
cleaning the printhead lens91
clearing paper jams56
configuration menus
Parallel
MAC Binary PS39
Mode 239
NPA Mode39
Protocol39
printing the Printer Settings Configuration sheet37
Setup
Auto CR after LF39
Auto LF after CR39
USB
MAC Binary PS38, 40
NPA Mode38, 40
Utilities
Hex Trace40
Print Quality Test Pages40
Reset Factory Defaults40
Reset Photoconductor Counter40
control panel
light sequences
Busy11
Canceling job15
Close door14, 17, 34
Defragment flash11
Error14, 15, 17, 18, 19, 20, 21, 25, 26, 27, 28, 34
Flushing data13
Formatting flash11
Hex Trace Ready12
Load manual feeder16
Load media15
Not ready13
Offline13
Photoconductor kit near full17Printer error20
Programming engine code18
Programming system code18
Ready/Power Saver11
Replace photoconductor kit18
Resetting printer15
Restoring factory defaults15
secondary error codes25
Service error19
Toner low16, 35, 36
Waiting12
lights8
D
duplex62
dust cover (optional)53
E
electronic emission statement93
emission statement93
envelopes46
Error light13, 14, 15, 17, 18, 19, 20, 21, 25, 26, 27, 28, 34
secondary error codes25
See also control panel, secondary error codes
extending trays52
F
FCC statement93
folio52
G
guidelines
paper
unacceptable45
printing letterhead62, 66
H
Hex Trace (Utilities menu)40
I
interfaces
parallel39
USB38, 40
J
jams56
Downloaded From ManualsPrinter.com Manuals 
						

							100Index  L
labels46
legal52
letterhead45, 66
page orientation62, 66
printing62, 66
lights8
Load Paper light
250-sheet tray or 550-sheet drawer15
manual feeder16
loading
250-sheet tray49
550-sheet drawer49
letterhead66
manual feeder54
Local Printer Setup Utility75
M
MAC Binary PS
Parallel menu39
USB menu38, 40
maintaining the printer
cleaning the printhead lens91
manual duplex
printing62
manual feeder16, 54
maximum paper fill indicators49, 50
media
guidelines
letterhead, printing62, 66
letterhead
loading instructions based on source62, 66
memory card72
menu settings page74
menus
navigating
advancing in38
entering37
exiting38
returning to Home menu38
scrolling through38
Parallel39
saving settings38
Setup39
USB38, 40
Utilities40
Mode 2 (Parallel menu)39
multiple page printing64
N
NPA Mode
Parallel menu39
USB menu38, 40
N-up printing64O
Operating modes86
options
memory card72
overlays66
P
paper
choosing43
jams56
loading49, 54
recommended types43
storing47
unsatisfactory types45
Parallel menu39
photoconductor kit
changing82
level78
light sequences79
ordering76
recycling84
Photoconductor kit near full light17
ports
parallel39
USB38, 40
print cartridge
See toner cartridge
print media
guidelines
paper43
print media specifications
characteristics44
print quality problems87
Print Quality Test Pages (Utilities menu)40
Printer Settings Configuration sheet
printing37
printhead lens, cleaning91
printing
booklets65
duplex62
letterhead66
multi-page (N-up)64
overlays66
watermarks66
problems
print quality87
Protocol (Parallel menu)39
R
rear exit55
recycling supplies84
Replace photoconductor kit light18
Reset Factory Defaults (Utilities menu)40
Reset Photoconductor Counter (Utilities menu)40
Downloaded From ManualsPrinter.com Manuals