Lexmark C760 Service Manual

Repair information4-15
  5060-4xx
4.Hold the front cover and remove the two screws (B) from the upper front pivot cover.
5.Remove the front cover assembly. 

4-16Service Manual
5060-4
xx   
Rear cover
Go to “Rear cover” on page 7-5  for part number.
1.Remove the outer system board shield. See  “Outer system board shield” on page 4-54 .
2.Remove 12 rear cover screws (A) type “232” on page 4-3 and type “323” on page 4-3 .
3.Open MPF door. 

Repair information4-17
  5060-4xx
4.Remove two screws (B).
5.Remove tabs (C) from slots (D).
6.Remove the rear cover. 
Note:   Make sure the toroid (E) is positioned at the edge of the inner system board shield. 

4-18Service Manual
5060-4
xx   
Lower right door assembly
Go to “Lower right door assembly” on page 7-3  for part number.
1.Open the lower right door assembly.
2.Remove the front lower right cover. See “Front lower right cover” on page 4-12 .
3.Loosen the two screws (A).
4.Remove the lower right door assembly.
Left lower cover
See “Fuser assembly” on page 7-7  for part numbers
1.Remove the lower jam access door assembly. See  “Lower jam access door assembly” on page 4-19 .
2.Remove the left lower cover...

Repair information4-19
  5060-4xx
Lower jam access door assembly
Go to “Cover, left lower” on page 7-5  for part number.
1.Remove the paper path access door cover. See  “Paper path access door cover” on page 4-11 .
2.Remove the front left handle cover assembly. See  “Front left handle cover assembly” on page 4-11 .
3.Remove the lower jam access door assembly screws (A) type  “323” on page 4-3 and remove the door.
Redrive door
Go to “Redrive door assembly” on page 7-14  for part number.
1.Open the...

4-20Service Manual
5060-4
xx   
Autocompensator pick assembly
1.Remove the ITU assembly. See “ITU assembly” on page 4-44.
2.Remove tray 1.
3.Remove the transfer plate. Lifting and rotating the right edge of the plate up to a 45° angle releases the 
transfer plate. Remove the grounding strap (A) attached to the bottom of the transfer plate. 
A 

Repair information4-21
  5060-4xx
4.Remove the black mylar piece by removing the two screws (B) or cutting the cable tie.
5.Remove the front lower left cover. See  “Front lower left cover” on page 4-10 . 
6.Remove the three screws (C) type “323” on page 4-3 to remove the front left handle cover assembly. 
7.Remove the pin (D) that holds in the MPF swing arm assembly. 
B
D 

4-22Service Manual
5060-4
xx   
8.Remove the MPF swing arm assembly (E).
9.Remove the paper level sensor. There are two screws located under the back VTB belt. Remove both of 
them along with a third that is located at the rear pivot point for the transfer plate (F). This allows the paper 
level assembly to drop into the cavity that the tray is inserted into. Disconnect the cable from the paper level 
sensor. Pull the paper lever sensor cable up through the opening. Remove the paper level sensor...

Repair information4-23
  5060-4xx
10.Disconnect the pick motor connector (G).
Paper Level Sensor 

4-24Service Manual
5060-4
xx   
11.Remove four screws (H) holding the pick assembly in place. 
12.Push the bellcrank (I) in to allow the pick arm to fall to the bottom of the tray. 
I