Lexmark C 950 Service Manual

Repair information 4-297
  5058-030
Go Back Previous
Next
23.Remove the 6 mm bushing (H).
24.Move the lower media exit roll assembly (F) towards the rear and outward, as shown.
25.Remove the lower media exit roll assembly (F).
Lower pinch guide assembly removal
1.Open the finisher front door assembly. 
2.Open the lower pinch guide assembly (A) by lifting it upward.
3.Remove the screw securing the lower pinch guide assembly (A) to the finisher.
FrontE-clip
HG
GRear 

4-298  Service Manual 5058-030  
Go Back Previous
Next
4.Move the lower pinch guide assembly (A) upward and outward.
5.Remove the lower pinch guide assembly (A).
Media compiler unit assembly removal
1.Remove the finisher front door assembly. See“Finisher front door assembly removal” on page 4-280.
2.Remove the rear upper cover. See “Rear upper cover removal” on page 4-313.
3.Remove the rear lower cover. See “Upper media bin front cover removal” on page 4-357.
4.Remove the upper media bin assembly. See...

Repair information 4-299
  5058-030
Go Back Previous
Next
11.Move the plate to the right and outward.
12.Remove the plate.
13.Disconnect the connector P8309 from the finisher controller card assembly (B).
14.Release the harness from the clamps.
ARear
BRearP8309 Clamp 

4-300  Service Manual 5058-030  
Go Back Previous
Next
15.Remove the screw securing the media compiler unit assembly (C) to the finisher. This screw is found 
inside the finisher.
Inside view 

Repair information 4-301
  5058-030
Go Back Previous
Next
16.Release the media compiler assembly (C) by pushing the front lock and the rear lock inward to release the 
front boss and the rear boss from the finisher.
17.Remove the harness from any additional parts.
18.Remove the media compiler unit assembly through the inside of the finisher and out the front.
Media eject clamp clutch removal
1.Remove the rear upper cover. See “Rear upper cover removal” on page 4-313.
2.Disconnect the connector from the...

4-302  Service Manual 5058-030  
Go Back Previous
Next
7.Remove the screw securing the spring clamp (D) to the finisher.
8.Remove the spring clamp (D).
9.Remove the media eject clutch actuator (C).
10.Remove the media eject clamp clutch (B).
Installation note: Make sure the hook on the media eject clamp clutch is placed in the notch of the bracket.
Media eject motor assembly removal
1.Remove the rear upper cover. See “Rear upper cover removal” on page 4-313.
2.Remove the media eject clutch. See “Media...

Repair information 4-303
  5058-030
Go Back Previous
Next
5.Remove the three screws securing the media eject motor assembly (A).
6.Remove the media eject motor assembly (A).
7.Remove any remaining harnesses from the clamps.
Media eject unit assembly removal
1.Remove the finisher front door assembly. See “Finisher front door assembly removal” on page 4-280.
2.Remove the rear upper cover. See “Rear upper cover removal” on page 4-313.
3.Remove the upper media bin assembly. See “Upper media bin assembly...

4-304  Service Manual 5058-030  
Go Back Previous
Next
8.Remove the screw securing the eject clamp lever assembly (C) from the shaft (D) on the rear of the 
finisher.
9.Remove the eject clamp lever assembly (C).
10.Remove the e-clip securing the shaft (D) to the rear of the finisher.
11.Remove the 8 mm bushing (E) on the rear side.
12.Remove the e-clip securing the shaft (F) to the front of the finisher.
Rear
C
Screw E-clip
E D 

Repair information 4-305
  5058-030
Go Back Previous
Next
13.Remove the 8 mm bushing (E) on the front side.
14.Gently move the left side of the media eject unit assembly (G) out of the finisher followed by the right side.
Note:  Do not force the media eject unit assembly out of the finisher. Remove the left side before the right 
side.
Note:  Tilting the media eject unit assembly slightly may make the removal easier.
15.Remove the media eject unit assembly.
•Do not force the media eject unit assembly...

4-306  Service Manual 5058-030  
Go Back Previous
Next
•Make sure the media eject unit assembly properly actuates the switch (eject cover interlock) (H) without 
binding.
Media entrance pinch guide assembly removal
1.Open the finisher front door assembly. 
2.Remove the rear upper cover. See “Rear upper cover removal” on page 4-313.
3.Remove the left lower cover. See “Left lower cover removal” on page 4-292.
4.Remove the left upper cover. See “Left upper cover removal” on page 4-293.
5.Remove the screw...