Lexmark C 950 Service Manual

Repair information 4-287
  5058-030
Go Back Previous
Next
Finisher removal
1.Disconnect the finisher power cord and the finisher connection cable from the rear of the printer.
2.Release the hook securing the bridge unit hookup cover (A) to the finisher.
3.Remove the bridge unit hookup cover (A).
4.Disconnect the bridge unit connection from the finisher.
5.Open the finisher front door assembly (B) on the front of the finisher.
Right
RearA Hook 

4-288  Service Manual 5058-030  
Go Back Previous
Next
6.Pull the finisher docking latch assembly (C) outward in the direction of the arrow, and pull the finisher away 
from the printer.
7.Close the finisher front door assembly.
C
B 

Repair information 4-289
  5058-030
Go Back Previous
Next
8.Remove the two screws securing the finisher docking bracket (D) to the printer.
9.Remove the finisher docking bracket (D).
Reinstallation note:  When docking the finisher to the printer, make sure the boss on the finisher docking 
bracket (D) is inserted into the hole on the finisher docking latch assembly (C). The finisher should be firmly 
locked into position.
Finisher right carriage belt removal
1.Remove the rear upper cover. See “Rear upper...

4-290  Service Manual 5058-030  
Go Back Previous
Next
4.Move the stacker bin (B) to its lowest position.
Note:  Make sure the stacker bin is at the lowest position before continuing.
5.Remove the two screws securing the bin bracket (C) to the right carriage bracket (D).
6.Remove the spring (E) from the right carriage bracket (D).
7.Remove the screw securing the upper belt clamp (F) to the right carriage bracket (D).
8.Remove the upper belt clamp (F).
9.Remove the right carriage bracket (D) with the...

Repair information 4-291
  5058-030
Go Back Previous
Next
Reinstallation notes:
•Make sure the finisher right carriage belt assembly (G) is inserted into the upper belt clamp (F) as shown.
•Make sure the bin bracket (C) is level to prevent binding.
C
D
EF G
Rear
H 

4-292  Service Manual 5058-030  
Go Back Previous
Next
Left lower cover removal
1.Open the finisher front door assembly.
2.Remove the two screws securing the left lower cover (A).
3.Remove the left lower cover (A).
A 

Repair information 4-293
  5058-030
Go Back Previous
Next
Left upper cover removal
1.Open the finisher front door assembly.
2.Remove the two screws securing the left upper cover (A).
3.Remove the left upper cover (A).
Lower media exit roll assembly removal
1.Remove the finisher front door assembly. See “Finisher front door assembly removal” on page 4-280.
2.Remove the rear upper cover. See “Rear upper cover removal” on page 4-313.
3.Remove the upper media bin assembly. See “Upper media bin assembly...

4-294  Service Manual 5058-030  
Go Back Previous
Next
18.Remove the belt (exit) (B) from the lower exit roll drive pulley 20T (C).
AB
Rear
C A
Tighten
first Tighten
second 

Repair information 4-295
  5058-030
Go Back Previous
Next
19.Release the hook of the lower exit roll drive pulley 20T (C) from the lower media exit roll assembly (F).
20.Remove the lower exit roll drive pulley 20T (C).
D
E
Front view
Rear view 

4-296  Service Manual 5058-030  
Go Back Previous
Next
21.Remove the 6 mm ball bearing (G).
22.Use a prying tool to remove the e-clip on the front of the finisher securing the lower media exit roll 
assembly (F) to the finisher.
F
G
C