Lexmark C 746 Service Manual
Have a look at the manual Lexmark C 746 Service Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 166 Lexmark manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Repair information4-115 5026 Go Back Previous Next High-voltage power supply (HVPS) removal See “High-voltage power supply” on page 7-13 for the part number. 1.Remove the left cover. See “Left cover removal” on page 4-31. 2.Remove the six mounting screws (A). 3.Release the locking tab (B) from the front, lower corner of the HVPS. A B
4-116Service Manual 5026 Go Back Previous Next 4.Disconnect the five connectors (C) from the HVPS. Installation notes: •Make sure to replace the spring when replacing the HVPS. •There are two types of spring forces on the cartridge contacts. Make sure to put the springs in their appropriate slots and are oriented properly. C
Repair information4-117 5026 Go Back Previous Next High-voltage power supply (HVPS) cable removal 1.Remove the rear upper cover. See “Rear upper cover removal” on page 4-50. 2.Disconnect the cable connector at JHVPS1 on the system board. 3.Disconnect the cable connector (B) from the HVPS. 4.Remove the cable from the hole through the frame (C), and from the two cable restraints (D).
4-118Service Manual 5026 Go Back Previous Next Left bell crank assembly removal See “Left bellcrank assembly, with spring” on page 7-7 for the part number. 1.Remove the left cover. See “Left cover removal” on page 4-31. 2.Remove the C-clip (A). 3.Remove the left bell crank assembly. A
Repair information4-119 5026 Go Back Previous Next Low-voltage power supply (LVPS) removal See “Low-voltage power supply” on page 7-9 for the part number. 1.Remove the right cover. See “Right cover removal” on page 4-51. 2.Remove the rear frame cover. See “Rear frame cover removal” on page 4-47. 3.Disconnect the connector at JLVPS1 connector (A) on the system board. 4.Remove the five LVPS mounting screws (B). 5.Disconnect the AC fuser cable (C) from the LVPS. A
4-120Service Manual 5026 Go Back Previous Next Installation note: •When installing the new LVPS, make sure the voltage switch (A) is set for the proper value (115 V or 230 V), depending on the country. Note: Not all LVPS FRUs have a switch. Others are switched automatically. •Install the LVPS, and make sure the AC fuser cable is in the cable guides, and not behind the LVPS. •Reconnect the AC fuser cable to the LVPS. •Replace the five LVPS mounting screws. •Reconnect the cable in connector JLVPS1 on the system board.
Repair information4-121 5026 Go Back Previous Next Motor driver card removal 1.Remove the right cover. See “Right cover removal” on page 4-51. 2.Disconnect the three cables (A). 3.Remove the two screws (B), and remove the motor driver card.
4-122Service Manual 5026 Go Back Previous Next Motor driver cable removal 1.Remove the LVPS. See “Low-voltage power supply (LVPS) removal” on page 4-119. 2.Disconnect the connector in JDVR1 (A) on the system board. 3.Disconnect the connector on the motor driver card (B). 4.Remove the cable from the cable from the four cable retainers (C). Installation note: Pay attention to the routing of the cable and the cable retainers.
Repair information4-123 5026 Go Back Previous Next Multipurpose feeder (MPF)/duplex gear and housing removal See the multipurpose feeder/duplex gear and housing kit for the part number. 1.Remove the paper pick mechanism assembly. See “Paper pick mechanism assembly removal” on page 4-137. 2.Remove the two E-clips (A) from the gears. 3.Remove the three screws (B). 4.Slide the front gear (C) off. A BC
4-124Service Manual 5026 Go Back Previous Next 5.Slide a flathead screwdriver up and under the front cover. 6.Slide the remaining two gears and housings off.