Lawn Mower 8211-7060-20 85 Combi, 95 Combi, 105 Combi For Mountfield 2000 And 4000 Series Instruction Manual

85 Combi, 95 Combi, 105 Combi for
8211-7060-20
INSTRUCTIONS FOR USEMODE D’EMPLOI
GEBRUIKSAANWIJZING
GEBRAUCHSANWEISUNG
ИНСТРУКЦИЯ  ПОЛЬЗОВАТЕЛЯ EN .... 5
FR... 10
NL ... 15
DE .. 20
RU .. 25
Mountfield 2000 and 4000 series 

2
2000-series, 4000-series 4WD
A B
C (D)
90°
A
B
C
4000-series 2WD
G F
E
P PQ
Q 45 Nm
R
3
5 
7 1
4
6 
8 2 

3
4000-series 4WD
2000-series
16”
4000-series 2WD
17”
11
13
15 9 
12
14
16 10  

4
1/3
19
 
  17
20
 
18  

5
ENGLISHEN
Original instructions for use
1 GENERAL
This symbol indicates WARNING. Seri-
ous personal injury and/or damage to 
property may result if the instructions 
are not followed carefully.
You must read these instructions for use 
and the machine’s safety instructions 
carefully.
1.1 SYMBOLSThe following symbols appear on the machine. 
They are there to remind  you of the care and atten-
tion required in use.
This is what the symbols mean:
Warning!
Read the instruction manual and the safety...

6
ENGLISHEN
Original instructions for use
3 ASSEMBLY
3.1 MACHINES WITH FIXED DECK CONNECTIONS
Example of fixed deck  connections, see 3:C and 
4:G.
1. Place the deck in position in front of the ma- chine.
2. Check that the deck mounts are installed on the  machine as follows.
4000-series 2WD
:
• Deck mount (4:G).
• Washer (4:F).
• Lock pin (4:E).
4000-series 4WD, 2000-series
:
• Washer (3:D). Only machines up to and in- cluding 2006.
• Deck mount (3:C).
• Washer (3:B).
• Circlip (3:A).
3. Remove pins and...

7
ENGLISHEN
Original instructions for use
4 USING THE MACHINE
Check that the grass that is to be cut is 
completely free of foreign objects such 
as stones etc.
4.1 CUTTING HEIGHTThe best cutting results are achieved when the 
when the top third of the grass is cut off. I.e. 2/3 of 
the length of the grass remains. See fig. 14.
If the grass is long and has to be cut significantly, 
cut twice using different cutting heights.
Do not use the lowest cutting heights if the lawn 
surface is uneven. This w ould...

8
ENGLISHEN
Original instructions for use
5. Release the belt tension as follows:4000-series 2WD:
Remove the tensioner from the belt. See fig. 10.
4000-series 4WD
:
Grip the belt tensioner’s lever with your left 
hand. Pull the lever and  remove the tensioner 
with your right hand. See fig. 9.
2000-series
:
Remove the tensioner from the belt. See fig. 11.
6. Force the belt off the machines’s pulley.
7. Grip the front edge of  the deck and lift up. Lift 
until the deck is completely vertical and rest the...

9
ENGLISHEN
Original instructions for use
5.5.3 Synchronising, blades
The deck has synchronised blades.
If one of the blades has struck a solid object (e.g. a 
stone), the synchronisation may be altered. This 
entails a risk of the blades colliding with each oth-
er.
Correctly synchronised blad es must be offset 90° 
from each other. See fig. 7.
Always check synchronisation after a collision.
If the blades are not sync hronised, one or more of 
the following faults may have occurred in the cut-
ting...

10
FRANÇAISFR
Traduction de la notice originale
1 GÉNÉRALITÉS
Ce symbole est un AVERTISSEMENT. 
Risque de blessure ou de dégât matériel 
en cas de non-respect des instructions.
Lire attentivement les instructions et les 
consignes de sécurité  avant d’utiliser la 
machine.
1.1 SYMBOLESLes symboles suivants figurent sur la machine. Ils 
attirent votre attention sur les dangers d’utilisation 
et les mesure s à respecter.
Explication des symboles:
Attention! 
Lire le mode d’emploi  et le manuel de sé-...