Land Rover Lt230q Overhaul Rover Manual

TRANSFERBOX
14 OVERHAUL
Mainshaft
inputgearassembly
NOTE: Defender inputgearillustrated.
1.Secure handpress LRT-99-002 inavice.
2. Assemble collarsLRT-41-003 aroundbearing
to be removed.
3. Position mainshaft inhand press, remove and
discard bearing.
4. Repeat aboveprocedure forremaining
bearing. Differential
lockselector
1.Remove anddiscard self-locking nutretaining
selector lever.
2. Remove washerandselector lever.
3. Withdraw selectorfingerandshaft from
housing.
4. Remove anddiscard Oring.   

TRANSFERBOX
OVERHAUL 15
Differential
1. Secure differential inasoft-jawed vice.
2. Remove stakingfrombearing retaining nut.
3.Remove nutusing toolLRT-41-007; discard
nut.4. Secure handpress LRT-99-002 inavice.
5. Secure collarsLRT-41-001 aroundrear
bearing.
NOTE: Thisbearing isadjacent to
threaded endofdifferential shaft.
6.Position differential inhand press withthrust
button, partoftool LRT-41-001 betweenpress
mandrel anddifferential shaft.
7. Press differential outofbearing.
CAUTION:...

TRANSFERBOX
16 OVERHAUL
9.Remove highrange gearandbush taking care
not todisturb high/low selectorsleeve.
10. Make suitable alignment marksbetween
high/low selectorsleeveandhub.
11. Remove high/lowselectorsleeve.
12.Using asuitable pullerandthrust button, part
of tool LRT-41-001, removehigh/low huband
low range gear.   

TRANSFERBOX
OVERHAUL 17
13.Secure handpress LRT-99-002 inavice.
14. Assemble collarsLRT-41-002 aroundfront
bearing.
NOTE: Thisbearing isadjacent tosplined
end ofdifferential shaft.
15.Position differential inhand press withthrust
button, partoftool LRT-41-001 betweenpress
mandrel anddifferential shaft.
16. Press differential outofbearing.
CAUTION: Takecarethatdifferential does
not drop outofbearing.
17. Remove differential frompress, discard
bearing.
18. Secure rearhalfofdifferential carrierina...

TRANSFERBOX
18 OVERHAUL
INSPECTING
COMPONENTS
1. Clean allcomponents, removealltraces of
silicone sealantusingsolvent andaplastic
scraper.
2. Clean alltraces ofLoctite andsealant from
threads ofbolts andtapped holes.Ensure
holes areclean anddry.
CAUTION: Donot use atap toclear
threads intapped holes.
3.Check allcasings andcovers forcracks and
damage.
4. Replace anycomponent foundtobe worn or
damaged. Intermediate
gearsandshaft
1. Check gearteeth forcracks, chipping and
uneven wear.
2. Check shaftforwear...

TRANSFERBOX
OVERHAUL 19
Mainshaft
inputgear
1. Check gearteeth forcracks, chipping and
uneven wear.
2. Check thatcross drillings inshaft areclear.
Defender only
3.Check thatends ofdog teeth arenot
rounded-off orchipped. High/low
crossshaftandhousing
1. Check mating surfaces ofcross shaftand
drilling inhousing forwear.
2. Check corepluginhousing forsigns of
leakage orcorrosion, applyLoctite 326to
replacement plug.
3.Check high/low selectorfingerforwear.
4. Measure acrosswidestportion offinger:
Finger...

TRANSFERBOX
20 OVERHAUL
Front
output housing anddifferential lock
selector
1. Check bearing trackrecesses inhousing for
damage, rectifyorreplace housing as
necessary.
2. Check differential lockselector fingershaftand
drilling inhousing forwear.
3.Check differential lockselector fingerforwear.
4. Measure acrosswidestportion offinger:
Finger width=15.90 to15.95 mm(0.625 to
0.627 in)
5.Check differential lockselector fingergroove
width indifferential lockselector shaft:
Groove width=16.0 to16.1 mm(0.63...

TRANSFERBOX
OVERHAUL 21
13.
Check dogclutch internal teethandgrooves for
wear anddamage.
14. Check dogclutch selector forkgroove width:
Groove width=8.05 to8.20 mm(0.32 to0.33
in)
15. Check threads andsplines ofoutput shaftfor
damage andwear.
16. Check dogclutch teethonshaft forwear and
damage. Rear
output housing
1. Check bearing trackrecess inhousing for
damage, rectifyorreplace housing as
necessary.
2. Check speedometer driveanddriven gearsfor
damage andwear.
3. Check splines andthreads ofoutput...

TRANSFERBOX
22 OVERHAUL
Main
casing
1. Check bearing trackrecesses inmain casing
for damage, rectifyorreplace casingas
necessary.
2. Remove drainplug,discard sealingwasher.
3. Fitnew sealing washer, fitdrain plugand
tighten to30 Nm (22lbf.ft).
4. Remove fillerplug, check threads fordamage.
5. Fitbut donot fully tighten fillerplug.
6. Check thatlocating dowelsarefitted incasing
and thatblade offront output housing dowelis
positioned asshown.
7. Remove oiltemperature switch-if fitted,
remove...

TRANSFERBOX
OVERHAUL 23
High/low
selectorforkandshaft
NOTE: Thereisno need toremove
selector forkfrom shaft unless forkor
shaft isto be replaced. Iffork isremoved,
coat threads ofset screw withLoctite 290prior
to assembly.
1. Check detentgrooves inshaft forwear.
2. Check high/low selectorfingergroove widthin
shaft: Groove width=16.0 to16.1 mm(0.63 to0.64
in)
3. Check high/low selectorforkforcracks and
wear.
4. Check high/low selectorforkfinger width:
Finger width=7.37 to7.47 mm(0.290 to0.294
in)