Land Rover Lr3 Owners Handbook 2004 Rover

311
Fuses
R
Passenger Compartment Fuses
The fuse removal tweezers are located in the 
passenger compartment fuse box. Place the 
tweezers onto the head of the suspect fuse (as 
shown), squeeze the middle (arrowed) and pull 
to remove. A break in the wire inside the fuse 
indicates that the fuse has blown and must be 
replaced.Always replace a fuse with another of the same 
value, however, if the replacement fuse blows 
immediately the circuit MUST be checked by a 
qualified Land Rover Retailer....

Fuses
312
L
Fuse specification
Fuse 
numberRating 
(amps)Circuit protected
1 10 Interior lamps - glovebox lamp, vanity mirror lamp, map lamps, 
switchable roof lamps
2 10 RH sidelamps
3 10 Theater lamps
4 10 LH sidelamps
5 10 Reverse lamps
6 10 Tow reverse lamp
7 25 Driver’s window
8 30 Trailer pick-up (battery feed)
95SRS
10 - -
11 10 Washer pump
12 15 Horn
13 25 HRW
14 10 Tow side lamp
15 15 Brake lamps, Brake switch
16 10 Powerfold mirror
17 20 Rear RH window
18 5 Rain sensor, ambient light sensor...

313
Fuses
R
35 5 Air suspension ECU
36 5 Tire pressure monitoring/Park Distance Control
37 5 Dynamic Stability Control
38 15 Front fog lamps
39 5 Instrument pack
40 5 Key in sense
41 5 Electric park brake
42 30 Audio amp
43 10 RF receiver, tire pressure monitoring
44 5 PRNDS Auto transmission selector
45 - -
46 30 Driver electric seat
47 15 Socket accessory - Row 3
48 15 Rear wiper
49 30 Central door locking
50 10 Electric fuel flap actuator
51 10 HEVAC ECU
52 5 Telephone, traffic message center
53 15...

Fuses
314
L
Tow hitch fuses
The supplementary fuse box that protects the 
tow hitch circuits, is located behind the 
left-hand panel in the luggage compartment.
H5792G
1
2
3
4
5
6
1. Brake lamp 7.5 amp
2. Ignition feed 15 amp
3. Battery feed 15 amp
4. Rear fog lamps 7.5 amp
5. Right-hand tail 
lamp5 amp
6. Number plate 
and left-hand tail 
lamp5 amp 

315
Bulb Replacement
R
Bulb Replacement
REPLACING BULBS
Check the operation of all exterior lamps before 
you drive the vehicle.
Caution: Before replacing a bulb, always 
switch off the starter switch and appropriate 
lighting switch to prevent any possibility of a 
short circuit. Only replace bulbs with the 
same type and specification.
Replacement bulbs
Note: All bulbs must be rated at 12 volts
Note: In certain territories it is a legal 
requirement to carry spare bulbs, in case of 
bulb failure. A...

Bulb Replacement
316
L
HEADLAMP UNIT
The headlamp unit contains five lamps and it is 
necessary to completely remove the unit from 
the vehicle in order to change any of the bulbs.
WARNING
Do not attempt to change any bulb with the 
lighting switched on. If the lighting has just 
been switched off, give the bulbs time to cool 
down. Handling them in a hot condition could 
cause personal injury.
Removal of headlamp unit
1.Remove the grille by pressing down on the 
top four clips, and up on the bottom two,...

317
Bulb Replacement
R
Bulb access
The five bulbs within the headlamp unit, 
accessible under domed caps are:
1.Direction indicator
2.Dipped beam/xenon
3.Main beam
4.Side lamp and cornering lamp
*/static 
bending lamp
See Replacement bulbs, 315.Note: To access the direction indicator, the 
headlamp unit locking slide must be completely 
removed from the unit.
12
34
H5713G
H5714G 

Bulb Replacement
318
L
To change a main or dipped beam bulb 
(Halogen only)
Main beam
1.Twist and lift off the domed cap.
2.Pull off the electrical connector.
3.Release the spring clip holding the bulb in 
place and lift out the bulb.
4.Insert the new bulb and repeat the above 
procedure in reverse order. When replacing 
the cap, align the arrowheads on the cap 
and the body of the unit.
Note: After the replacement of any main or 
dipped beam bulb, the alignment of the 
headlamps should be checked by a...

319
Bulb Replacement
R
To change a xenon bulb
1.Twist and lift off the domed cap.
2.Twist the connector cap anticlockwise to 
unlock it. Pull clear of the bulb.
Note: After the replacement of any main or 
dipped beam bulb, the alignment of the 
headlamps should be checked by a Land Rover 
Retailer.3.Release the spring clip holding the bulb in 
place and lift out the bulb.
4.Insert the new bulb and repeat the above 
procedure in reverse order. When replacing 
the cap, ensure that the lugs are in contact...

Bulb Replacement
320
L
Changing a cornering lamp/static bending 
bulb
*
1.Twist and lift off the domed cap.
2.Pull out the bulb complete with electrical 
connector.
3.To release the bulb, squeeze the sides of 
the electrical connector.
4.Insert the new bulb and repeat the above 
procedure in reverse order.
When replacing the cap, align the 
arrowheads on the cap and the body of the 
unit.Changing a front side lamp bulb
1.Twist and lift off the domed cap.
2.Pull out the bulb complete with electrical...