Land Rover Discovery Series Ii 2002my Owners Handbook Nas Rover
Here you can view all the pages of manual Land Rover Discovery Series Ii 2002my Owners Handbook Nas Rover. The Land Rover manuals for Automobile are available online for free. You can easily download all the documents as PDF.
Page 211
Bulb Replacement 210 HEADLIGHT AND SIDELIGHT Light unit removal First remove the access panel set into the bonnet locking platform above each headlight.To replace either the headlight or sidelight bulb, remove the light unit as follows: Disengage the retaining clips ‘A’ and rotate them approximately 10 degrees (see inset) until they align with the slots in the headlight mounting panel. The light unit can now be released forward. NOTE: DO NOT screw or unscrew the retaining clips more than described...
Page 212
Bulb Replacement 211 Headlight bulb replacement Disconnect the electrical multi-plug and remove the rubber cover. Release the spring clip which holds the bulb and withdraw the bulb from the light unit. When replacing the bulb, ensure that the larger tab is pointing towards the top of the headlight. Replace the spring clip and rubber cover, ensuring the slit in the cover is at the top of the headlight, and pressing the centre firmly to seal around the electrical contacts of the bulb. NOTE: Do not...
Page 213
Bulb Replacement 212 FRONT DIRECTION INDICATOR AND SIDE MARKER LIGHT Remove the retaining screw ‘A’, then ease the light unit forward to release it from the vehicle. Both the small side marker light and larger direction indicator bulb holders are released from the light unit by twisting anti-clockwise. Pull the side marker bulb to remove. Push and twist the direction indicator bulb to remove. To replace the light unit, insert the two location pins (arrowed) on the outer side of the light unit into...
Page 214
Bulb Replacement 213 REAR LIGHT CLUSTER (Tail, stop & reverse lights) From outside the vehicle remove the four retaining screws to release the light unit from the vehicle, then detach the electrical multi-plug connector, by pressing the metal retaining spring. To gain access to the bulbs, remove the five screws from the rear of the light unit and detach the bulb holder. Push and twist to release each bulb. H2506
Page 215
Bulb Replacement 214 BUMPER MOUNTED LIGHTS (Fog guard lights & direction indicators) WARNING If the engine is warm, the exhaust system may be hot - to prevent personal injury, avoid contact with a hot exhaust system when reaching behind the bumper. Reach behind the bumper and press the spring clip ‘A’ to release the light unit. Squeeze both levers ‘B’ to release the bulb holder from the lens. Push and twist to release the bulbs. NOTE: If necessary, the light unit can first be detached from the...
Page 216
Bulb Replacement 215 FRONT FOG LIGHTS The front fog lights are mounted on the rear of the front bumpers and are shielded from behind by the lower wheelarch liners. Access is severely restricted and will entail lying beneath the centre of the vehicle at the front and reaching between the wheelarch liner and the back of the fog light. To access the bulb, remove the cover on the rear of the fog light by twisting it anti-clockwise.Spring clips (similar to those in the headlights) hold the bulb in...
Page 217
Bulb Replacement 216 HIGH MOUNTED STOP LIGHT Remove both retaining screws and the cover from the rear of the light unit. Twist the bulb holder anti-clockwise to remove. Push and twist anti-clockwise to release the bulb. GLOVEBOX LIGHT Insert a small flat-bladed screwdriver (preferably with a short handle, due to limited access) into the indent (arrowed in illustration) on the left hand side of the light unit, and carefully prise the unit from the glovebox panel. Remove the bulb from its...
Page 218
Bulb Replacement 217 INTERIOR COURTESY LIGHTS Insert a small flat-bladed screwdriver into the indent on the side of the lens and carefully prise the lens from the light unit, then pull the bulb to remove. When replacing the lens, first locate the lug (arrowed in illustration), then push the lens into position. INTERIOR LIGHT Insert a small flat-bladed screwdriver into the indent on the side of the lens (where arrowed) and prise the lens from the light unit, then pull the bulb out from the...
Page 220
219 Technical Data Technical Data LUBRICANTS AND FLUIDS . . . . . . . . . . . . . . . . 221 CAPACITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223 ENGINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . 224 STEERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 VEHICLE WEIGHTS . . . . . . . . . . . . . . . . . . . . . ....