Land Rover Defender Workshop 1993 Rover Manual

BODY 
Refit REAR DOOR TRIM CASING 
Service repair no - 76.34.09 
Remove 
12.  With  assistance, position  rear headlining to roof 
and locate  rear corners in  cant rail. 
13.  Push headlining  rearwards and position  over 
rear  end lining  mounting brackets. 
14.  Locate  front corners  of headlining  in cant  rail. 
15.  Position front  edge of rear headlining  over front 
headlining  and secure  with trim studs. 
16.  Adjust rear  headlining to achieve  good fit at  all 
corners. 
17.  Fit  rear...

BODY 
4. Remove sun roof. 
5.  Starting  from centre  rear,  peel headlining finisher 
from  inner  frame. 
6. Remove  18 screws  securing  inner frame  to outer 
frame and detach  inner frame. 
7. Lift outer frame from roof. 
SUN ROOF 
Service  repair no - 76.82.15 
Remove 
NOTE: Assistance  may be required  to remove  the 
sun  roof  assembly. 1. Open  sun roof  fully. 
2. Disengage  spring lock  from operating handle 
catch. 
3.  Holding sun  roof at both sides,  release hinges 
from  locating...

BODY 
5. Remove caps and unscrew  front seat belt fixing 
bolts  from B/C  posts. 
6. Carefully  prise side trim panel  cap fastener  from 
B/C  posts. 
7. Carefully  prise 2 trim studs,  from both sides, 
securing  headlining  to body  at door  aperture. 
8. Carefully  prise out 5 trim studs  securing  front 
and  rear  headlinings  to roof. 
9.  From  both sides,  pull side  trim panel  inwards 
FRONT  HEADLINING 
Service  repair no 
- 76.64.10 
Remove 
1. Remove  sun roof  headlining  finisher. 
2....

BODY 
INTERIOR REAR VIEW MIRROR SUN VISORS 
Service repair no - 76.10.51 
Remove  Remove 
Service 
repair no - 76.10.17. 
1. Remove  retaining  screw securing mirror 
2. Slide adjustment arm up from mounting  slug and 
1. Raise sun visor. 
2. Remove 2 screws and  collect sun visor. 
adjustment  ann to mounting slug. 
remove  rear view mirror. 
J6053 2 
Ref it 
3. Position  sun visor  and secure with 2 screws. 
Refit 
3. Slide  mirror  adjustment  arm  over mounting  slug. 
4.  Secure  mirror with...

BODY 
base. 
3.  Prise  seat belt retaining clip  from side 
of seat 
mounting and remove trim  studs. 
4.  Unscrew  bolt and remove  seat belt inertia reel 
from  roll
-over bar mounting bracket. 
5. Remove seat  belt and  inertia reel  assembly. 
6. Unscrew bolt and  washer  and  remove seat  belt 
buckle  stalk from roll
-over mounting bracket. 
7. On the  drivers side,  disconnect harness plug 
connector of audible  warning circuit at buckle 
stalk. 
FRONT SEAT BELTS 
Service  repair no - 76.73.13...

BODY 
3. Remove two torx bolts, from both sides,  securing 
top  bar 
to roof  mounting. 
4. Slide  top bars  rearwards to disengage  from main 
roll
-over  bar assembly. 
5. Lift main  roll-over bar assembly  from vehicle 
6. If necessary,  remove 2 torx bolts and nuts,  from 
both  sides,  and detach  lower cross  bar from 
main  roll
-over bar. 
EXTERIOR  ROLL-OVER BAR 
Service repair no - 76.11.39 
Remove 
1. Remove  tom bolt,  from  both sides,  securing  top 
of  roll
-over  bar to roof mounted...

BODY 
2. Remove 4 bolts and spring washers securing 
tow  bar centre  mounting  bracket 
to chassis. 
3. Remove both bolts securing  the two  tow  bar 
locating  tubes in rear chassis  cross member. 
4. Remove 2 bolts securing  tow bar top  mounting 
brackets  to chassis. 
5. With assistance,  withdraw tow bar assembly 
from chassis. 
REAR TOW BAR 
Service  repair no 
- 76.11.41 
Remove 
1. Remove bolt,  washer and nut from  both sides, 
securing  tow bar lower mounting brackets and 
towing eyes  to...

ELECTRICAL 
REAR WIPER MOTOR Refit 
Service repair no - 84.35.12 
Remove 
8. Locate  wiper motor  drive spindle  through 
9. Position  wiper motor  mounting  bracket and 
aperture 
in rear  door. 
secure  to rear  door.  Tighten  bolt to 
23 Nm (17 
Ibf.ft). 
10.  Reconnect  harness multi
-plug. 
11.  Secure  drive spindle  to door. 
12.  Fit wiper  motor  cover. 
13.  Fit rear  wiper  arm. 
1. 
With  assistance,  unscrew 3 retaining  nuts and 
remove  spare wheel  from rear door  mounting 
studs. 
nut....

ELECTRICAL 
SWITCH PANEL-REAR DOOR SERVICES Refit 
Service repair no - 86.65.78 
Remove 
5. Feed harness  into switch  panel and reconnect 
6. Position  switch panel on fascia  and secure  with 
switch 
multi
- plugs. 
trim  studs. 
1. Carefully  prise out 4 trim studs  securing  switch 
panel 
to centre  of fascia. 
2. Withdraw  switch panel and disconnect 
multi
-plugs  from the three  switches. 
3.  Pull  harness  multi
-plugs through  aperture  in 
base  of panel. 
2  

ELECTRICAL 
SWITCHES - TAILGATE  FUNCTIONS  INTERIOR LAMP 
Service  repair no 
- 84.35.33  Rear wiper switch 
Service repair  no 
- 84.30.27 Rear wash  switch 
Service repair  no 
- 86.65.36 Heated rear screen 
switch 
and  roof  mounting  bracket. 
Remove harness plug. 
Service  repair no - 86.45.02 
Remove 
1. Carefully  prise lens cover  from lamp  unit. 
2.  Remove 
2 nuts  securing  lamp unit to headlining 
3. Release  lamp from bracket  studs and disconnect 
1. Carefully  prise out 4 trim studs...